delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MSIEnable bit is only available for the 8169.

Avoid Config2 writes for the post-8169 8168 and 810x.
Reported-by: NSu Kang Yin <cantona@cantona.net>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 92fc43b4, rtl8169_tx_timeout ends up
resetting Rx and Tx indexes and thus racing with the NAPI handler via
-> rtl8169_hw_reset
   -> rtl_hw_reset
      -> rtl8169_init_ring_indexes

What about returning to the original state ?

rtl_hw_reset is only used by rtl8169_hw_reset and rtl8169_init_one.

The latter does not need rtl8169_init_ring_indexes because the indexes
still contain their original values from the newly allocated network
device private data area (i.e. 0).

rtl8169_hw_reset is used by:
1. rtl8169_down
   Helper for rtl8169_close. rtl8169_open explicitely inits the indexes
   anyway.
2. rtl8169_pcierr_interrupt
   Indexes are set by rtl8169_reinit_task.
3. rtl8169_interrupt
   rtl8169_hw_reset is needed when the device goes down. See 1.
4. rtl_shutdown
   System shutdown handler. Indexes are irrelevant.
5. rtl8169_reset_task
   Indexes must be set before rtl_hw_start is called.
6. rtl8169_tx_timeout
   Indexes should not be set. This is the job of rtl8169_reset_task anyway.

The removal of rtl8169_hw_reset in rtl8169_tx_timeout and its move in
rtl8169_reset_task do not change the analysis.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Realtek has specified that the post 8168c gigabit chips and the post
8105e fast ethernet chips recover automatically from a Rx FIFO overflow.
The driver does not need to clear the RxFIFOOver bit of IntrStatus and
it should rather avoid messing it.

The implementation deserves some explanation:
1. events outside of the intr_event bit mask are now ignored. It enforces
   a no-processing policy for the events that either should not be there
   or should be ignored.

2. RxFIFOOver was already ignored in rtl_cfg_infos[RTL_CFG_1] for the
   whole 8168 line of chips with two exceptions:
   - RTL_GIGA_MAC_VER_22 since b5ba6d12
     ("use RxFIFO overflow workaround for 8168c chipset.").
     This one should now be correctly handled.
   - RTL_GIGA_MAC_VER_11 (8168b) which requires a different Rx FIFO
     overflow processing.

   Though it does not conform to Realtek suggestion above, the updated
   driver includes no change for RTL_GIGA_MAC_VER_12 and RTL_GIGA_MAC_VER_17.
   Both are 8168b. RTL_GIGA_MAC_VER_12 is common and a bit old so I'd rather
   wait for experimental evidence that the change suggested by Realtek really
   helps or does not hurt in unexpected ways.

   Removed case statements in rtl8169_interrupt are only 8168 relevant.

3. RxFIFOOver is masked for post 8105e 810x chips, namely the sole 8105e
   (RTL_GIGA_MAC_VER_30) itself.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Round-up some wayward "N/A" fw_version dust bunnies as part of that
clean-up.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the number of #defines, use the normal #define from if_ether.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.

Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.

Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for reporting ring sizes via ethtool -g to the 8139cp driver.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- fix features : jumbo frames and checksumming can not be used at the
  same time.

- introduce hw_jumbo_{enable / disable} helpers. Their content has been
  creatively extracted from Realtek's own drivers. As an illustration,
  it would be nice to know how/if the MaxTxPacketSize register operates
  when the device can work with a 9k jumbo frame as its documentation
  (8168c) can not be applied beyond ~7k.

- rtl_tx_performance_tweak is moved forward. No change.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

8168d and above allow jumbo frames beyond 8k. Bump the received
packet length check before enabling jumbo frames on these chipsets.

Frame length indication covers bits 0..13 of the first Rx descriptor
32 bits for the 8169 and 8168. I only have authoritative documentation
for the allowed use of the extra (13) bit with the 8169 and 8168c.
Realtek's drivers use the same mask for the 816x and the fast ethernet
only 810x.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Support new chips of RTL8111F.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>

For RTL8111EVL, the register of MaxTxPacketSize doesn't acctually
limit the tx size. It influnces the feature of early tx.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>

MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well.  It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled.  This caused a dependency error.

Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.

This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers.  In
addition, by enabling all the new Kconfig options does not add
any un-expected options.

CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the Realtek drivers into drivers/net/ethernet/realtek/ and make
the necessary Kconfig and Makefile changes.

CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Jeff Garzik <jgarzik@pobox.com>
CC: Donald Becker <becker@scyld.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>