Unlike other sorts of endpoint queues, Isochronous queues don't stop
when an error is encountered.  This patch (as772) fixes the scanning
routine in uhci-hcd, to make it keep on going when it finds an Iso
error.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Apparently some UHCI controllers change the value of the Short Packet
Detect (SPD) bit in the TD status word -- presumably when they receive a
short packet.  This patch (as759) changes uhci-hcd to avoid assuming
that the bit is unchanged; in fact, the driver no longer looks at SPD at
all.

This fixes the second problem reported in Bugzilla #6752.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as707) improves the FSBR operation in uhci-hcd by turning it
off more quickly when it isn't needed.  FSBR puts a noticeable load on a
computer's PCI bus, so it should be disabled as soon as possible when it
isn't in use.  The patch leaves it running for only 10 ms after the last
URB stops using it, on the theory that this should be long enough for a
driver to submit another URB if it wants keep FSBR going.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as705) contains a small set of updates for uhci-hcd written
mostly by Dave Brownell:

  * Root hub suspend messages come out labeled as root hub messages;
    PCI messages should only come out when the pci device suspends.

  * Rename the reset() method to better match its init() role

  * Behave more like the other HCDs by returning -ESHUTDOWN for root-hub
    suspend/resume errors.

  * When an URB fails, associate the message with the usb device not
    the host controller (it still hides endpoint and direction)

From: David Brownell <david-b@pacbell.net>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as690) does the same thing for ISO TDs as as680 did for
non-ISO TDs: free them as they are used rather than all at once when an
URB is complete.  At the same time it fixes a minor buglet (I'm not
aware of it ever affecting anyone): An ISO TD should be retired when its
frame is over, regardless of whether or not the hardware has marked it
inactive.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as689) stores the period for periodic transfers (interrupt
and ISO) in the queue header.  This is necessary for proper bandwidth
tracking (not yet implemented).  It also makes the scheduling of ISO
transfers a bit more rigorous, with checks for out-of-bounds frame
numbers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as688) fixes a small race in uhci-hcd.  Because ISO queues
aren't controlled by queue headers, they can't be unlinked.  Only
individual URBs can.  So whenever multiple ISO URBs are dequeued, it's
necessary to make sure the hardware is done with each one.  We can't
assume that dequeuing the first URB will suffice to unlink the entire
queue.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some old Intel UHCI controllers have a bug that has shown up in a few
systems (the PIIX3 "Neptune" chip set).  Until now there has not been
any simple way to work around the bug, but the lastest changes in
uhci-hcd have made it easy.  This patch (as684) adds the work-around.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as683) re-implements Full-Speed Bandwidth Reclamation (FSBR)
properly.  It keeps track of which endpoint queues have advanced, and
when none have advanced for a sufficiently long time, FSBR is turned
off.  The next TD on each of the non-moving queues is modified to
generate an interrupt on completion, so that FSBR can be re-enabled as
soon as the hardware starts to make some progress.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as682) gets rid of the TD-removal list in uhci-hcd.  It is
no longer needed because now TDs are not freed until we know the
hardware isn't using them.  It also simplifies the code for adding and
removing TDs to/from URBs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as681) moves some code for cleaning up after unlinked URBs
out of the general completion pathway into the unlinking pathway.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as680) frees non-isochronous TDs as they are used, rather
than all at once when an URB is complete.  Although not a terribly
important change in itself, it opens the door to a later enhancement
that will reduce storage requirements by allocating only a limited
number of TDs at any time for each endpoint queue.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as679) combines the result routine for Control URBs with the
routine for Bulk/Interrupt URBs.  Along the way I eliminated the
debugging printouts for Control transfers unless the debugging level is
set higher than 1.  I also eliminated a long-unused (#ifdef'ed-out)
section that works around some buggy old APC BackUPS devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as676) fixes a small bug in uhci-hcd's enqueue routine.  When
an URB is unlinked or gets an error and the completion handler queues
another URB for the same endpoint, the queue shouldn't be allowed to start
up again until the handler returns.  Not even if the new URB is the only
one on its queue.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as675) simplifies uhci-hcd slightly by storing each endpoint's
type in the corresponding Queue Header structure.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as640) removes several put_device and the corresponding
get_device calls from the USB core and HCDs.  Some of the puts were done
in atomic contexts, and none of them are needed since the core now
guarantees that every endpoint will be disabled and every URB completed
before a USB device is released.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A recent update to the uhci-hcd driver invoked the list_prepare_entry
macro incorrectly.  This patch (as646) corrects it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Even when the URB_SHORT_NOT_OK flag is set, a short transfer shouldn't
generate a debugging log message.  Especially not one with the confusing
claim that the transfer "failed with status 0".  This patch (as627)
fixes that behavior in uhci-hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as626) makes some improvements to the debugging code in
uhci-hcd.  The main change is that now the code won't get compiled if
CONFIG_USB_DEBUG isn't set.  But there are other changes too, like
adding a missing .owner field and printing a debugging dump if the
controller dies.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As part of reorienting uhci-hcd away from URBs and toward endpoint
queues, this patch (as625) eliminates the driver's main list of URBs.
The list wsa used mainly in checking for URB completions; now the driver
goes through the list of active endpoints and checks the members of the
queues.

As a side effect, I had to remove the code that looks for FSBR timeouts.
For now, FSBR will remain on so long as any URBs on a full-speed control
or bulk queue request it, even if the queue isn't advancing.  A later
patch can add more intelligent handling.  This isn't a huge drawback;
it's pretty rare for an URB to get stuck for more than a fraction of a
second.  (And it will help the people trying to use those insane HP USB
devices.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as624) fixes a hardware race in uhci-hcd by adding a dummy
TD to the end of each endpoint's queue.  Without the dummy the host
controller will effectively turn off the queue when it reaches the end,
which happens asynchronously.  This leads to a potential problem when
new transfer descriptors are added to the end of the queue; they may
never get used.

With a dummy TD present the controller never turns off the queue;
instead it just stops at the dummy and leaves the queue on but inactive.
When new TDs are added to the end of the queue, the first new one gets
written over the dummy.  Thus there's never any question about whether
the queue is running or needs to be restarted.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as623) changes the uhci-hcd driver to make it use one QH per
device endpoint, instead of a QH per URB as it does now.  Numerous areas
of the code are affected by this.  For example, the distinction between
"queued" URBs and non-"queued" URBs no longer exists; all URBs belong to
a queue and some just happen to be at the queue's head.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some USB devices don't enumerate well with FSBR turned on.  This patch
keeps devices on the low-speed part of the schedule (which doesn't use
FSBR) until they have been fully configured.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as615b) edits a large number of comments in the uhci-hcd code,
mainly removing excess apostrophes.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as616) changed the uhci_explen macro in uhci-hcd.h so that
it now accepts the desired length, rather than length - 1 with special
handling for 0.  This also fixes a minor bug that would show up only
when a driver submits a 0-length bulk URB.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The uhci-hcd driver is fairly lax about the way it handles isochronous
transfers.  This patch (as579) improves it in three respects:

	TDs for a new URB aren't added to the schedule until all of
	them have been allocated.  This way there's no risk of the
	controller executing some of them when an allocation fails.

	TDs for an unlinked URB are removed from the schedule as soon
	as the URB is unlinked, rather than waiting until the URB is
	given back.  This way there's no risk of the controller still
	executing a TD after the URB completes.

	The urb->error_count values are now reported correctly.
	Although since they aren't used in any drivers except for
	debug messages in the system log, probably nobody cares.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces.  This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages.  It also allows
the logical array to be allocated in non-DMA-coherent memory.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL.  In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen.  Hence there's no longer any need to check for partial
initialization.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR).  The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Greg,

This patch fixes the kmalloc() flags argument type in USB
subsystem; hopefully all of its occurences. The patch was
made against patch-2.6.12-git2 from Jun 20.

Cleanup of flags for kmalloc() in USB subsystem.
Signed-off-by: NOlav Kongas <ok@artecdesign.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch simplifies the uhci-hcd driver by removing the device pointer
currently stored in the QH and TD structures.  Those pointers weren't
being used for anything other than to increment the device's reference
count, which is unnecessary since the device is used only when an URB
completes, and outstanding URBs take their own reference to the device.
As a useful side effect, this change means that uhci-hcd no longer needs
to have the root-hub device available in the start routine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch, which has as478b as a prerequisite, enables the uhci-hcd
driver to take advantage of root-hub IRQs rather than polling during the
time it is suspended.  (Unfortunately the hardware doesn't support
port-change interrupts while the controller is running.)  It also turns
off the driver's private timer while the controller is suspended, as it
isn't needed then.  The combined elimination of polling interrupts and
timer interrupts ought to be enough to allow some systems to save a
noticeable amount of power while they are otherwise idle.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes a few small improvements in the UHCI driver.  Some
code is moved between different source files and a more useful pointer
is passed to a callback routine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!