This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated
and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant
function declarations and data structures.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>

Signed-off-by: NEdwin Peer <epeer@tmtservices.co.za>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This adds support for Raumfeld's 'Controller', 'Connector', 'Speaker S'
and 'Speaker M' devices. They're all based on PXA303 SoCs.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Due to the naming mess in Kconfig and Makefile, I'd like to get them sorted
in the following order:

 1. By category:
    Intel/Marvell Dev Platforms, followed by 3rd party platforms, followed
    by end-user products (this is to ensure the commonly referenced platforms
    will appear first)

 2. By vendor name in alphabetic within each category
    (this is to ensure code reuse and similar platforms can be grouped as
     much as possible)

	   VENDOR        BOARD
	Intel/Marvell   Lubbock
	Intel/Marvell   Mainstone
	Intel/Marvell   Zylonite
	Intel/Marvell   Littleton
	Intel/Marvell   TavorEVB
	Intel/Marvell   SAAR

	Accelent        IDP
	Arcom/Eurotech  VIPER
	Community       Balloon3
	Cogent          CSB726
	CompuLab        EM_X270
	CompuLab        EXEDA
	CompuLab        ARMCORE
	CompuLab        CM_X300
	Gumstix         Gumstix
	Intel Research  MOTE2
	Intel research  Stargate2
	Iskratel        XCEP
	Keith and Koep  Trizeps4
	LogicPD         LPD270
	Phytec          PCM027
	Toradex         Colibri

	HP              HX4700
	HP              H5000
	HTC             Himalaya
	HTC             Magician
	Mitac           MioA701
	Motorola        EZX
	NEC             MP900C
	Palm            Palm PDA
	Palm            Palm GSM
	Sharp           Zaurus
	Toshiba         E-Series
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NTomáš Čech <sleep_walker@suse.cz>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

So, again against latest pxa-linux-2.6/devel, with the following
changes:

 * Move to __raw_readl/__raw_writel for FPGA/CPLD register access
 * Change Toppoly LCD config to be selectable at run time rather than
   compile time.
 * Remove currently unused irq device suspend/resume functions.
 * Strip out unnecessary/duplicated #includes.
 * Some code style cleanups.

Balloon3 (http://balloonboard.org/) base machine support
Signed-off-by: NJonathan McDowell <noodles@earth.li>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Added support for the Iskratel XCEP single board computer, embedded in
instruments used in particle accelerators.

The patch contains the platform specific code, Makefile and Kconfig
changes for platform arm-pxa.
Signed-off-by: NAleš Bardorfer <ales.bardorfer@i-tech.si>
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: NMatej Kenda <matej.kenda@i-tech.si>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds basic support for Palm Tungsten|C handheld.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NTomáš Čech <sleep_walker@suse.cz>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This includes
- IrDA (pxafixp_ir),
- Buttons (gpio-keys),
- ASIC3 IRQ/GPIOs (asic3),
- EGPIOs (htc-egpio),
- ATI Imageon w3220 framebuffer (w100fb),
- Backlight (pwm-backlight),
- StrataFlash (physmap),
- Battery monitor (ds1wm,w1_ds2760,ds2760_battery)
- USB gadget support (pxa27x_udc,gpio_vbus).
- bq24022 battery charger (pda_power,bq24022)
- TSC2046 touchscreen (ads7846)
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

The PXA_PWM config option is really redundant since the introduction
of HAVE_PWM, replace that with HAVE_PWM to avoid confusion.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This contains support for keypad, MMC, AC97, LCD and backlight.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

1. add common GPIO handling code into [arch/arm/plat-pxa]

2. common code in <mach/gpio.h> moved into <plat/gpio.h>, new processors
   should implement its own <mach/gpio.h>, provide the following required
   definitions and '#include <plat/gpio.h>' in the end:

   - GPIO_REGS_VIRT for mapped virtual address of the GPIO registers'
     physical I/O memory

   - macros of GPLR(), GPSR(), GPDR() for constant optimization for
     functions gpio_{set,get}_value() (so that bit-bang code can still
     have tolerable performance)

   - NR_BUILTIN_GPIO for the number of onchip GPIO

   - definitions of __gpio_is_inverted() and __gpio_is_occupied(), they
     can be either macros or inlined functions
Signed-off-by: NEric Miao <eric.miao@marvell.com>

1. introduce folder of 'arch/arm/plat-pxa' for common code across different
   PXA processor families

2. initially moved DMA code into plat-pxa

3. common code in <mach/dma.h> moved into <plat/dma.h>, new processors
   should implement its own <mach/dma.h>, provide the following required
   definitions and '#include <plat/dma.h>' in the end:

   - DMAC_REGS_VIRT for mapped virtual address of the DMA registers'
     physical I/O memory
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This adds basic support for Colibri PXA320 modules.
The file colibri-320.c only contains settings specific to this module,
such as the Ethernet interface.

Cc: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

- Move common function for all Colibri PXA3xx boards to the newly
  added colibri-pxa3xx.c
- Drop some unnecessary defines from colibri.h
- Make Kconfig reflect the fact that code for colibri 300 module does
  also work for the 310 model
- Give up on the huge pin config table which was messed up with lots of
  #ifdefs and switch over to locally defined tables for configured
  functions

Cc: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This patch add basic support for Toradex' Colibri PXA300 module.
Ethernet is enabled conditionally, depdending on CONFIG_AX88796.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Namespace cleanup: rename colibri.c to colibri-pxa270.c and change
some names in colibri.h.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

CSB701 is one of baseboards that can be used with CSB726 SOM.
This currently adds support for button and LED on the board.
More to come later.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Patch adds support for the HTC Himalaya device. It includes hardware definitions and w100fb support.
Signed-off-by: NZbynek Michl <Zbynek.Michl@seznam.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the AM300 platform driver which uses the
E-Ink broadsheetfb display driver.

Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Changes made as suggested by Eric Miao (including fix to map_io
silly mistake!).

Originally designed by Intel, now sold by Crossbow (www.xbow.com).

Very little actually on board. The patch includes sensors and
similar as found on commonly occurring daughter boards.

Some of the drivers are not in mainline as yet as they are either
part of the IIO subsystem or need a lot of work before submission.
What is the position wrt to putting them in i2c board configs etc?

Support for these boards has been maintained outside the kernel
for a long time, but now that there is a good da9030 pmic driver
available the last major hurdle no longer exists.

All comments welcomed.

The Imote2's big brother (stargate2) will follow once any problems
with this one have been cleaned up and a few bits and bobs have
been added to the da903x driver. Hopefully the cc2420 driver will
get cleaned up and submitted in the not too distant future as
well.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: Andre Puschmann <andre.puschmann@imms.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.

Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).

Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.

This machine will be used as "real user" for these new drivers.

This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NMilan Plzik <milan.plzik@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.

This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRuss Dill <russ.dill@gmail.com>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRuss Dill <russ.dill@gmail.com>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRuss Dill <russ.dill@gmail.com>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>