This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Whereas most Orion 5x machine support code would initialise the PCI
subsystem with nr_controllers in their struct hw_pci set to 2, the
DNS323 and Kurobox Pro machine support code had nr_controllers set
to 1.

This was presumably done because on those two machines, the PCI(-X)
controller (nr == 1) isn't used, requiring initialisation of only
the PCIe controller (nr == 0.)  However, not initialising the PCI(-X)
controller on boards that don't use it leads to a situation where
both the PCIe and the PCI(-X) controller think that their root bus is
zero, and it messes up IRQ assignment.

This patch changes the DNS323 and Kurobox Pro support code to always
use nr_controllers == 2.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The CPU's dma_flush_range() operation needs to clean+invalidate the
given memory area if the cache is in writeback mode, or do just the
invalidate part if the cache is in writethrough mode, but the current
proc-arm{925,926,940,946} (incorrectly) do a cache clean in the
latter case.  This patch fixes that.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Martin Michlmayr reported that fuse complains:
  ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!

so export the needed function.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5033/1: Unbreak corgi_ssp by registering ssp drivers earlier.
  [ARM] Orion: clean up addr-map.c after window setting code purge
  [ARM] Orion: pass proper t_clk into mv643xx_eth
  [ARM] Orion: use mv643xx_eth driver mbus window handling
  [ARM] pxa: Fix RCSR handling
  [ARM] lubbock: fix compilation
  [ARM] 5032/1: Added cpufreq support for pxa27x CPU
  [ARM] 5031/1: Indentation correction in cpu-pxa.c.
  [ARM] 5028/1: pxafb: fix broken "backward compatibility way" in framebuffer
  [ARM] 4882/2: Correction for S3C2410 clkout generation
  [ARM] 5027/1: Fixed random memory corruption on pxa suspend cycle.
  [ARM] 5024/1: Fix some minor clk issues in the MMCI PL18x driver
  [ARM] 5023/1: Fix broken gpio interrupts on ep93xx
  ns9xxx: fix sparse warning
  ns9xxx: check for irq lockups
  ns9xxx: fix handle_prio_irq to unmask irqs with lower priority

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  x86: rdc: leds build/config fix
  x86: sysfs cpu?/topology is empty in 2.6.25 (32-bit Intel system)
  x86: revert commit 709f744f ("x86: bitops asm constraint fixes")
  x86: restrict keyboard io ports reservation to make ipmi driver work
  x86: fix fpu restore from sig return
  x86: remove spew print out about bus to node mapping
  x86: revert printk format warning change which is for linux-next
  x86: cleanup PAT cpu validation
  x86: geode: define geode_has_vsa2() even if CONFIG_MGEODE_LX is not set
  x86: GEODE: cache results from geode_has_vsa2() and uninline
  x86: revert geode config dependency

The generic semaphore rewrite had a huge performance regression on AIM7
(and potentially other BKL-heavy benchmarks) because the generic
semaphores had been rewritten to be simple to understand and fair.  The
latter, in particular, turns a semaphore-based BKL implementation into a
mess of scheduling.

The attempt to fix the performance regression failed miserably (see the
previous commit 00b41ec2 'Revert
"semaphore: fix"'), and so for now the simple and sane approach is to
instead just go back to the old spinlock-based BKL implementation that
never had any issues like this.

This patch also has the advantage of being reported to fix the
regression completely according to Yanmin Zhang, unlike the semaphore
hack which still left a couple percentage point regression.

As a spinlock, the BKL obviously has the potential to be a latency
issue, but it's not really any different from any other spinlock in that
respect.  We do want to get rid of the BKL asap, but that has been the
plan for several years.

These days, the biggest users are in the tty layer (open/release in
particular) and Alan holds out some hope:

  "tty release is probably a few months away from getting cured - I'm
   afraid it will almost certainly be the very last user of the BKL in
   tty to get fixed as it depends on everything else being sanely locked."

so while we're not there yet, we do have a plan of action.
Tested-by: NYanmin Zhang <yanmin_zhang@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alexander Viro <viro@ftp.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit bf726eab, as it has
been reported to cause a regression with processes stuck in __down(),
apparently because some missing wakeup.

Quoth Sven Wegener:
 "I'm currently investigating a regression that has showed up with my
  last git pull yesterday.  Bisecting the commits showed bf726e
  "semaphore: fix" to be the culprit, reverting it fixed the issue.

  Symptoms: During heavy filesystem usage (e.g.  a kernel compile) I get
  several compiler processes in uninterruptible sleep, blocking all i/o
  on the filesystem.  System is an Intel Core 2 Quad running a 64bit
  kernel and userspace.  Filesystem is xfs on top of lvm.  See below for
  the output of sysrq-w."

See

	http://lkml.org/lkml/2008/5/10/45

for full report.

In the meantime, we can just fix the BKL performance regression by
reverting back to the good old BKL spinlock implementation instead,
since any sleeping lock will generally perform badly, especially if it
tries to be fair.
Reported-by: NSven Wegener <sven.wegener@stealer.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

..instead of cooking up its own uglier local version of it.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It actually makes much more sense there, and we do tend to need it for
non-RCU usage too.  Moving it to <linux/compiler.h> will allow some
other cases that have open-coded the same logic to use the same helper
function that RCU has used.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

select NEW_LEDS for now until the Kconfig dependencies have been
fixed.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

System topology on intel based system needs to be exported
for non-numa case as well.

All parts of asm-i386/topology.h has come under
#ifdef CONFIG_NUMA after the merge to asm-x86/topology.h

/sys/devices/system/cpu/cpu?/topology/* is populated based on
ENABLE_TOPO_DEFINES

The sysfs cpu topology is not being populated on my dual socket
dual core xeon 5160 processor based (x86 32 bit) system.

CONFIG_NUMA is not set in my case yet the topology is relevant
and useful.

irqbalance daemon application depends on topology to build the
cpus and package list and it fails on Fedora9 beta since the
sysfs topology was not being populated in the 2.6.25 kernel.

I am not sure if it was intentional to not define ENABLE_TOPO_DEFINES
for non-numa systems.

This fix has been tested on the above mentioned dual core, dual socket
system.
Signed-off-by: NVaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org

709f744f causes my computer to freeze during the start up of X and my
login manger (GDM). It gets to the point where it has shown the default
X mouse cursor logo (a big X / cross) and does not respond to anything
from that point on.

This worked fine before 709f744f, and it works fine with 709f744f
reverted on top of Linus' current tree (f74d505b). The revert had
conflicts, as far as I can tell due to white space changes. The diff I
ended up with is below.

It is 100% reproducible.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

On some of our (single board computer) boards (x86) we are using an
IPMI controller that uses I/O ports 0x62 and 0x66 for a KCS (keyboard
controller style) IPMI system interface.

Trying to load the openipmi driver fails, because the ports
(0x62/0x66) are reserved for keyboard. keyboard reserves the full
range 0x60-0x6F while it doesn't need to.

Reserve only ports 0x60 and 0x64 for the legacy PS/2 i8042 keyboad
controller instead of 0x60-0x6F to allow the openipmi driver to work.

[ tglx: added 64bit fixup ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

If the task never used fpu, initialize the fpu before restoring the FP
state from the signal handler context. This will allocate the fpu
state, if the task never needed it before.
Reported-and-bisected-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Tested-by: NEric Sesterhenn <snakebyte@gmx.de>
Cc: Frederik Deweerdt <deweerdt@free.fr>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Jeff Garzik pointed out that this printout is not needed.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

commit 62179849
    x86: fix setup printk format warning

is for linux-next and not for .26
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

A lot of stuff in spitz/akita/etc. depends on corgi_ssp to be initialised
early. However corgi_ssp initialisation fails, because at that time pxa*-ssp
devices don't have drivers. Move ssp earlier in the makefile so they are
registered before corgi-ssp.

Also move sleep/suspend and cpu-freq to more logical places
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (21 commits)
  Blackfin Serial Driver: abstract away DLAB differences into header
  Blackfin Serial Driver: macro away the IER differences between processors
  [Blackfin] arch: remove useless IRQ_SW_INT defines
  [Blackfin] arch: protect linux/usb/musb.h include until the driver gets mainlined
  [Blackfin] arch: protect linux/usb/isp1362.h include until the driver gets mainlined
  [Blackfin] arch: add EBIU supporting for BF54x EZKIT SMSC LAN911x/LAN921x families embedded ethernet driver
  [Blackfin] arch: Set spi flash partition on bf527 as like bf548.
  [Blackfin] arch: fix bug - Remove module will not free L1 memory used
  [Blackfin] arch: fix wrong header name in comment
  [Blackfin] arch: Fix BUG - spi flash on bf527 ezkit would fail at mount
  [Blackfin] arch: add twi_lcd and twi_keypad i2c board info to bf527-ezkit
  [Blackfin] arch: Add physmap partition for BF527-EZkit
  [Blackfin] arch: fix gdb testing regression
  [Blackfin] arch: disable single stepping when delivering a signal
  [Blackfin] arch: Delete unused (copied from m68k) entries in asm-offsets.c.
  [Blackfin] arch: In the double fault handler, set up the PT_RETI slot
  [Blackfin] arch: Support for CPU_FREQ and NOHZ
  [Blackfin] arch: Functional power management support: Add CPU and platform voltage scaling support
  [Blackfin] arch: fix bug -  breaking the atomic sections code.
  [Blackfin] arch: Equalize include files: Add VR_CTL masks
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] fix build warning
  [CIFS] Fixed build warning in is_ip
  [CIFS] cleanup cifsd completion
  [CIFS] Remove over-indented code in find_unc().
  [CIFS] fix typo
  [CIFS] Remove duplicate call to mode_to_acl
  [CIFS] convert usage of implicit booleans to bool
  [CIFS] fixed compatibility issue with samba refferal request
  [CIFS] Fix statfs formatting
  [CIFS] Adds to dns_resolver checking if the server name is an IP addr and skipping upcall in this case.
  [CIFS] Fix spelling mistake
  [CIFS] Update cifs version number

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (37 commits)
  SH: catch negative denormal_subf1() retval in denormal_add()
  sh: Fix DMAC base address for SH7709S
  sh: update smc91x platform data for se7206.
  sh: Stub in cpu_to_node() and friends for NUMA build.
  sh: intc register modify fix
  sh: no high level trigger on some sh3 cpus
  sh: clean up sh7710 and sh7720 intc tables
  sh: add interrupt ack code to sh3
  sh: unify external irq pin code for sh3
  sh-sci: avoid writing to nonexistent registers
  sh-sci: sh7722 lacks scsptr registers
  sh-sci: improve sh7722 support
  sh: reset hardware from early printk
  sh: drain and wait for early printk
  sh: use sci_out() for early printk
  sh: add memory resources to /proc/iomem
  sh: add kernel bss resource
  sh: fix sh7705 interrupt vector typo
  sh: update smc91x platform data for se7722
  sh: update smc91x platform data for MigoR
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] hmac: Avoid calling virt_to_page on key

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
  [POWERPC] Remove leftover printk in isa-bridge.c
  [POWERPC] Remove duplicate #include
  [POWERPC] Initialize lockdep earlier
  [POWERPC] Document when printk is useable
  [POWERPC] Fix bogus paca->_current initialization
  [POWERPC] Fix of_i2c include for module compilation
  [POWERPC] Make default cputable entries reflect selected CPU family
  [POWERPC] spufs: lockdep annotations for spufs_dir_close
  [POWERPC] spufs: don't requeue victim contex in find_victim if it's not in spu_run
  [POWERPC] 4xx: Fix PCI mem in sequoia DTS
  [POWERPC] 4xx: Add endpoint support to 4xx PCIe driver
  [POWERPC] 4xx: Fix problem with new TLB storage attibute fields on 440x6 core
  [POWERPC] spufs: spu_create should send inotify IM_CREATE event
  [POWERPC] spufs: handle faults while the context switch pending flag is set
  [POWERPC] spufs: fix concurrent delivery of class 0 & 1 exceptions
  [POWERPC] spufs: try to route SPU interrupts to local node
  [POWERPC] spufs: set SPU_CONTEXT_SWITCH_PENDING before synchronising SPU irqs
  [POWERPC] spufs: don't acquire state_mutex interruptible while performing callback
  [POWERPC] spufs: update master runcntl with context lock held
  [POWERPC] spufs: fix post-stopped update of MFC_CNTL register
  ...

m32r can use the generic sys_pipe implementation.

The current sys_pipe implementation on m32r only differes from the
generic one by passing a lot of additional unused registers to sys_pipe.

Reviewed and tested by Hirokazu Takata.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The cris implementation of sys_pipe only differs from the generic one
by taking the BKL before calling do_pipe which isn't not nessecary.

Just kill the cris implementation and use the generic one.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  sit: Add missing kfree_skb() on pskb_may_pull() failure.
  tipc: Increase buffer header to support worst-case device

Linus found a logic bug: we ignore the version number in a module's
vermagic string if we have CONFIG_MODVERSIONS set, but modversions
also lets through a module with no __versions section for modprobe
--force (with tainting, but still).

We should only ignore the start of the vermagic string if the module
actually *has* crcs to check.  Rather than (say) having an
entertaining hissy fit and creating a config option to work around the
buggy code.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We allow missing __versions sections, because modprobe --force strips
it.  It makes less sense to allow sections where there's no version
for a specific symbol the module uses, so disallow that.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Don't allow a module built without versions altogether to be inserted
into a kernel which expects modversions.

modprobe --force will strip vermagic as well as modversions, so it
won't be effected, but this will make sure that a
non-CONFIG_MODVERSIONS module won't be accidentally inserted into a
CONFIG_MODVERSIONS kernel.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch cleans up Orion's addr-map.c a bit after all peripheral
window programming code has been moved out into the relevant drivers.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Pass the Orion TCLK tick rate into the ethernet driver.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Make the Orion 5x platform code use the mbus window handling code
that's in the mv643xx_eth driver, instead of programming the GigE
block's mbus window registers by hand.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

'ix' is unsigned but denormal_subf1() may return a negative int.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This printk() appears twice in the same function.  Only the latter one
in the inval_range: section appears to be legitimate.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove duplicate #include of <asm/prom.h> in
arch/powerpc/kernel/btext.c.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This moves lockdep_init() to before udbg_early_init() as the later
can call things that acquire spinlocks etc...  This also makes printk
safer to use earlier.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When debugging early boot problems, it's common to sprinkle printk's
all over the place.  However, on 64-bit powerpc, this can lead to
memory corruption if done too early due to the PACA pointer and
lockdep core not being initialized.

This adds some comments to early_setup() that document when it is
safe to do so in order to save time for whoever has to debug that
stuff next.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When doing lockdep, I had two patches to initialize paca->_current
early, one bogus, and one correct.  Unfortunately both got merged
as the bad one ended up being part of the main lockdep patch by
mistake.  This causes memory corruption at boot.  This removes
the offending code.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove #ifdef CONFIG_OF_I2C as this breaks module compilation.
Drivers using this header should depend on OF_I2C anyways, so
there's no need to make this conditional.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>