Only rx_usec and tx_usec options for ethtool -C are settable as those
are the only settings that make sense to HW.  Adds driver reporting of
intr coalescing timer value in usec units rather than HW units.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous driver was aligning ring sizes to 16 descs, but hardware actually
wants desc ring sizes to be aligned to 32 descs.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In set_multicast(), only push pkt filter changes down to firmware if
pkt filter actually changes.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During dev->open(), make sure we get at least one skb on the Rx ring.
Otherwise abort the interface load.  Also, if we get skb allocation
failures in NAPI poll while trying to replenish the ring, try again
later so we don't end up starving out the Rx ring completely.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix dev->stop shutdown bug where driver was stopping xmit queue and then
disabling intrs.  Fix is to disable intrs first and then stop the xmit
queue, otherwise an interrupt could cause the queue to be rewoken.  Also,
no need to explicitly do queue servicing because queues are cleaned and
reset back to initial state at end of dev->stop.  Servicing queues also
had the side-effect of also rewakening the xmit queue, which is not what
we want.
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. remove address argument since we use same address IWMC_SDIO_DATA_ADDR in
    all cases
2. add __iwmct_tx - non locking tx function for already locked contexts
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. add TRACE level
2. use TRACE where needed to reduce the noise
3  don't INFOEX from driver
4. add DUMP level for packets dumps
5. use correct context for the log messages
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. removed redundant NULL-pointers checks in iwmct_fw_load
as release_firmware and kfree are NULL pointer friendly
2. remove redundant memset of the parser since the structure
is fully initialized in iwmct_fw_parser_init function
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Unified firmware image size can be < 1 MB
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Support pci error detection and recovery.
o Refactor suspend and resume code, to share with io_error_detected,
  and slot_reset callbacks
o NX_NEED_AER device state added, to synchronize with firmware
  recovery.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o In case of tx timeout, firmare may be healthy, but some pci-func may
  see no response from it. Force firmware reset, if some pci-func
  explicitly requests so.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o pci device should be disable at the end and it should be enable first.
o Interface should be attached(netif_device_attach()) irrespective
  of its state.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.

Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.

Fixed that.  Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: Npancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I made this patch for usbserial driver to add the support for EVDO modem
Haier CE100. The bugs report for this is here:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/490068

This patch based on these post:
http://blankblondtank.wordpress.com/2009/09/04/mengoptimalkan-koneksi-modem-haier-ce-100-cdma-di-linux/
http://tantos.web.id/blogs/how-to-internet-connection-using-cdma-evdo-modem-and-karmic-koala-ubuntu-9-10

I hope this patch can help other that have the Haier C100 modem, mostly in my country, Indonesia.
Signed-off-by: NDonny Kurnia <donnykurnia@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The wTotalLength should contain the sum of the interface and unit
descriptor sizes per the Audio Device Class specification 1.0.
Reported-by: NSergey Lapin <slapin@ossfans.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

commit 91c8a5a9 broke
compilation of this driver after it introduced
otg_init() as a static inline in <linux/usb/otg.h>
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some of these workarounds are already in place, but labeled as affecting
all BF52x parts.  Since we have official anomaly numbers now, use those
defines.  And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below array index out of bounds issue.

Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84

The data stored in 'aInfo' array exceeds the array size of 78.

This patch increases the size of this array to hold the string
correctly without any memory corruption.

This issue was reported by Klockwork tool.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the following NULL pointer dereference issue.

Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.

============
Code Snippet
============

748:  request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
	csr &= ~(MUSB_RXCSR_AUTOCLEAR
			| MUSB_RXCSR_DMAENAB
			| MUSB_RXCSR_DMAMODE);
	musb_writew(epio, MUSB_RXCSR,
		MUSB_RXCSR_P_WZC_BITS | csr);

792:	 request->actual += musb_ep->dma->actual_len;
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gadget stalling a zero-length SETUP request results in this error message:

SetupEnd came in a wrong ep0stage idle

In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request.  Add the missing '\n' to the error message itself as well...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO.  Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.

Update over previous patch to avoid taking the lock if already
taken.  Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.

Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: NArnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a null-pointer dereference bug.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
                                             pointer types lacks a cast

So switch to min_t(size_t, ...).
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

probe() already was on __init, so moving remove() to __exit.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 7723de7e (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.

Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.

Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).

Compile-tested, based on latest mainline git.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix new kernel-doc warnings in usb core:

Warning(drivers/usb/core/usb.c:79): No description found for parameter 'config'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'iface_num'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'alt_num'
Warning(drivers/usb/core/hcd.c:1622): No description found for parameter 'udev'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hi!

$ lsusb -v
Bus 001 Device 008: ID 05ac:921c Apple, Inc. 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x05ac Apple, Inc.
  idProduct          0x921c 
  bcdDevice            1.15
  iManufacturer           1 
  iProduct                2 
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      92
         Report Descriptors: 
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              16
Signed-off-by: Npancho horrillo <pancho@pancho.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 91777826 removed __init from
ehci_wait_for_port(), but left it in place on ehci_reset_port(), which
is being called from the former function.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Acked-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While converting emi62 to use request_firmware(), the driver was also
changed to use the ihex helper functions.  However, this broke the loading
of the FPGA firmware because the code tries to access the addr field of
the EOF record which works with a plain array that has an empty last
record but not with the ihex helper functions where the end of the data is
signaled with a NULL record pointer, resulting in:

BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f80d248c>] emi62_load_firmware+0x33c/0x740 [emi62]

This can be fixed by changing the loop condition to test the return value
of ihex_next_binrec() directly (like in emi26.c).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: NDer Mickster <retroeffective@gmail.com>
Acked-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NBlaise Gassend <blaise.gasend_linux@m4x.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch corrects a problem where drivers/usb/otg is linked twice
if CONFIG_USB_ULPI is selected, resulting in a build error (symbol
conflict). The files in that directory are properly linked already
as part of CONFIG_USB, and need not be indicated specifically for
CONFIG_USB_ULPI.
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use ERR_PTR and IS_ERR rather than mixing integers and pointers.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression *E;
@@

* E < 0
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1315) fixes some bugs in the USB core authorization
code:

	usb_deauthorize_device() should deallocate the device strings
	instead of leaking them, and it should invoke
	usb_destroy_configuration() (which does proper reference
	counting) instead of freeing the config information directly.

	usb_authorize_device() shouldn't change the device strings
	until it knows that the authorization will succeed, and it should
	autosuspend the device at the end (having autoresumed the
	device at the start).

	Because the device strings can be changed, the sysfs routines
	to display the strings must protect the string pointers by
	locking the device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Acked-by: NDavid Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1314) renames usb_configure_device() and
usb_configure_device_otg() in the hub driver.  Neither name is
appropriate because these routines enumerate devices, they don't
configure them.  That's handled by usb_choose_configuration() and
usb_set_configuration().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>