This patch implements handlers for the following NDO operations:

.ndo_set_vf_spoofchk
.ndo_set_vf_mac
.ndo_get_vf_config
.ndo_set_vf_trust
.ndo_set_vf_vlan
.ndo_set_vf_link_state
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.

Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Until now, all the VSI and queue management code supported only the PF
VSI type (ICE_VSI_PF). Update these flows to handle the VF VSI type
(ICE_VSI_VF) type as well.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements parts of ice_sriov_configure and VF reset flow.

To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.

VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.

Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Mailbox queue is a type of control queue that's used for communication
between PF and VF. This patch adds code to initialize, configure and
use mailbox queues.

This patch also adds support to detect and parse SR-IOV capabilities
returned by the hardware.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to other patches from ERic.

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

In netvsc driver it uses NAPI for TX completions. The default
poll_napi will do this for us now and avoid the capture.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns when one enumerated type is implicitly converted to another.

drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:390:4: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
                        IEEE_FAUX_SYNC(dev, dcb);
                        ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.h:70:10: note: expanded
from macro 'IEEE_FAUX_SYNC'
                                            CXGB4_DCB_STATE_FW_ALLSYNCED);
                                            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~

Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.

CXGB4_DCB_STATE_FW_ALLSYNCED = CXGB4_DCB_INPUT_FW_ALLSYNCED = 3
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns when one enumerated type is implicitly converted to another.

drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:303:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
                         ? CXGB4_DCB_STATE_FW_ALLSYNCED
                           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:304:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
                         : CXGB4_DCB_STATE_FW_INCOMPLETE);
                           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.

Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.

CXGB4_DCB_STATE_FW_INCOMPLETE = CXGB4_DCB_INPUT_FW_INCOMPLETE = 2
CXGB4_DCB_STATE_FW_ALLSYNCED = CXGB4_DCB_INPUT_FW_ALLSYNCED = 3
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns:

drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2734:34: warning:
tentative array definition assumed to have one element
static const struct of_device_id dpaa_match[];
                                 ^
1 warning generated.

Turns out that since this driver was introduced in commit 9ad1a374
("dpaa_eth: add support for DPAA Ethernet"), this declaration has been
unused. Remove it to silence the warning.
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Acked-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to obtain the correct table for the incoming interface was
missing for IPv6. This has been added along with the table creation
notification to fib rules for the RTNL_FAMILY_IP6MR address family.
Signed-off-by: NPatrick Ruddy <pruddy@vyatta.att-mail.com>
Signed-off-by: NMike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for inserting and deleting Rx flow classification
rules through ethtool.

We support classification based on some header fields for
flow-types ether, ip4, tcp4, udp4 and sctp4.

Rx queues are core affine, so the action argument effectively
selects on which cpu the matching frame will be processed.
Discarding the frame is also supported.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For firmware versions that support it, configure an Rx flow
classification key at probe time.

Hardware expects all rules in the classification table to share
the same key. So we setup a key containing all supported fields
at driver init and when a user adds classification rules through
ethtool, we will just mask out the unused header fields.

Since the key composition process is the same for flow
classification and hashing, reuse existing code where possible.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the array of supported header fields will be used for
Rx flow classification as well, rename it from "hash_fields" to
the more inclusive "dist_fields".
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Management Complex (MC) firmware initially allowed the
configuration of a single key to be used both for Rx flow hashing
and flow classification. This prevented us from supporting
Rx flow classification through ethtool.

Starting with version 10.7.0, the Management Complex(MC) offers
a new set of APIs for separate configuration of Rx hashing and
classification keys.

Update the Rx flow hashing support to use the new API, if available.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver_info field that is used for describing each of the usb-net
drivers using the usbnet.c core all declare their information as const
and the usbnet.c itself does not try and modify the struct.

It is therefore a good idea to make this const in the usbnet.c structure
in case anyone tries to modify it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add driver support for reading/configuring the 20G link speed via ethtool.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add driver support for configuring/reading the 20G link speed.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace "fallthru" with a proper "fall through" annotation.

This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver is unloaded when traffic is in progress, errors are
generated. Fix this by releasing qvectors and NAPI handler on remove.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:

1. Currently we are using multiple members to store the interrupt
   granularity (itr_gran_25/50/100/200). This is not necessary because
   we can query the device to determine what the interrupt granularity
   should be set to, done by a new function ice_get_itr_intrl_gran.

2. Added intrl to ice_q_vector structure to support interrupt rate
   limiting.

3. Added the function ice_intrl_usecs_to_reg for converting to a value
   in usecs that the device understands.

4. Added call to write to the GLINT_RATE register. Disable intrl by
   default for now.

5. Changed rx/tx_itr_setting to itr_setting because having both seems
   redundant because a ring is either Tx or Rx.

6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the ice_reset_req enum values have to be translated into
a different set of values that the hardware understands for the same
reset types. Avoid this translation by aligning ice_reset_req enum
values to the ones that the hardware understands.

Also add and else if block to check for ICE_RESET_EMPR and put a dev_dbg
message in the else case.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements ethtool hook for enabling/disabling
RSS. While disabling RSS, the LUT should be cleared. And
the LUT should be reconfigured while enabling RSS.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For the PF driver, when mapping interrupts to queues, we need to request
IRQs from the kernel and we also have to allocate interrupts from
the device.

Similarly, when the VF driver (iavf.ko) initializes, it requests the kernel
IRQs that it needs but it can't directly allocate interrupts in the device.
Instead, it sends a mailbox message to the ice driver, which then allocates
interrupts in the device on the VF driver's behalf.

Currently both these cases end up having to reserve entries in
pf->irq_tracker but irq_tracker itself is sized based on how many vectors
the PF driver needs. Under the right circumstances, the VF driver can fail
to get entries in irq_tracker, which will result in the VF driver failing
probe.

To fix this, sw_irq_tracker and hw_irq_tracker are introduced. The
sw_irq_tracker tracks only the PF's IRQ request and doesn't play any
role in VF init. hw_irq_tracker represents the device's interrupt space.
When interrupts have to be allocated in the device for either PF or VF,
hw_irq_tracker will be looked up to see if the device has run out of
interrupts.
Signed-off-by: NPreethi Banala <preethi.banala@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.

Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.

To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A VSI handle is just a number the driver maintains to uniquely identify
a VSI. A VSI handle is backed by a VSI number in the hardware. When
interacting when the hardware, VSI handles are converted into VSI numbers.

In commit 0f9d5027 ("ice: Refactor VSI allocation, deletion and
rebuild flow"), VSI handles were introduced but it was used only
when creating and deleting VSIs. This patch is part one of two patches
that expands the use of VSI handles across the rest of the driver. Also
in this patch, certain parts of the code had to be refactored to correctly
use VSI handles.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware

With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce driver-defined maximums for queue ring sizes. Devices
available for IBM vNIC today will likely not allow this amount,
but this should give us some leeway for future devices that may
support larger ring sizes.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase queue size limit to 16. Devices available for IBM vNIC today
will not allow this amount, but this should give us some leeway for
future devices that may support more RX or TX queues.
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Andrew Lunn <andrew@lunn.ch>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RSC feature -- a bit field "internal" was added here with total
size unchanged:
struct rndis_per_packet_info {
	u32 size;
	u32 type:31;
	u32 internal:1;
	u32 ppi_offset;
};

On TX path, we put rndis msg into skb head room, which is not zeroed
before passing to us. We do not use the "internal" field in TX path,
but it may impact older hosts which use the entire 32 bits as "type".

To fix the bug, this patch sets the field "internal" to zero.

Fixes: c8e4eff4 ("hv_netvsc: Add support for LRO/RSC in the vSwitch")
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using mod_delayed_work() allows to simplify handling delayed work and
removes the need for the sync parameter in phy_trigger_machine().
Also introduce a helper phy_queue_state_machine() to encapsulate the
low-level delayed work calls. No functional change intended.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When inserting the TSB, keep track of how many times we had to do it and
if there was a failure in doing so, this helps profile the driver for
possibly incorrect headroom settings.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During bcm_sysport_insert_tsb() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace path.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can turn on the RX/TX checksum offloads by default and make sure that
those are properly reflected back to e.g: stacked devices such as VLAN
or DSA.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During driver resume and open, the HW may have lost its context/state,
utilize bcm_sysport_set_features() to make sure we do restore the
correct set of features that were previously configured.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unconditionally enabling TX and RX checksum offloads,
refactor bcm_sysport_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure that
features are correctly programmed during network device registration.

Since we can now be called during register_netdev() with clocks gated,
we need to temporarily turn them on/off in order to have a successful
register programming.

We also move the CRC forward setting read into
bcm_sysport_set_features() since priv->crc_fwd matters while turning on
RX checksum offload, that way we are guaranteed they are in sync in case
we ever add support for NETIF_F_RXFCS at some point in the future.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds switch for flow director with ethtool command
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>