The A5XX GPU powers on in "secure" mode. In secure mode the GPU can
only render to buffers that are marked as secure and inaccessible
to the kernel and user through a series of hardware protections. In
practice secure mode is used to draw things like a UI on a secure
video frame.

In order to switch out of secure mode the GPU executes a special
shader that clears out the GMEM and other sensitve registers and
then writes a register. Because the kernel can't be trusted the
shader binary is signed and verified and programmed by the
secure world. To do this we need to read the MDT header and the
segments from the firmware location and put them in memory and
present them for approval.

For targets without secure support there is an out: if the
secure world doesn't support secure then there are no hardware
protections and we can freely write the SECVID_TRUST register from
the CPU. We don't have 100% confidence that we can query the
secure capabilities at run time but we have enough calls that
need to go right to give us some confidence that we're at least doing
something useful.

Of course if we guess wrong you trigger a permissions violation
which usually ends up in a system crash but thats a problem
that shows up immediately.

[v2: use child device per Bjorn]
[v3: use generic MDT loader per Bjorn]
[v4: use managed dma functions and ifdefs for the MDT loader]
[v5: Add depends for QCOM_MDT_LOADER]
Signed-off-by: NJordan Crouse <jcrouse@codeaurora.org>
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
[robclark: fix Kconfig to use select instead of depends + #if IS_ENABLED()]
Signed-off-by: NRob Clark <robdclark@gmail.com>

Linux 4.12-rc5 for nouveau fixes

imx-drm: cleanups and YUV 4:2:0 memory read/write reduction support

- Remove counter load enable form PRE, which has no effect.
- Add support for setting the double read/write reduction flag in channel
  parameter memory. This can be used to save some memory bandwidth when
  capturing in YUV 4:2:0 chroma subsampled formats.
- Allocate DMA channel structures as needed, most of the 64 channels are
  unused or even reserved.
- Remove unused interrupt busy waiting routine.
- Set VDIC field order for both AUTO and MAN inputs simultaneously as
  both can't be active at the same time.

* tag 'imx-drm-next-2017-06-08' of git://git.pengutronix.de/git/pza/linux:
  gpu: ipu-v3: vdic: include AUTO field order bit in ipu_vdi_set_field_order
  gpu: ipu-v3: remove interrupt busy waiting routine
  gpu: ipu-v3: allocate ipuv3_channels as needed
  gpu: ipu-v3: Add support for double read/write reduction
  gpu: ipu-v3: prg: remove counter load enable

some fsl-dcu cleanups

* tag 'drm-fsl-dcu-for-v4.13' of http://git.agner.ch/git/linux-drm-fsl-dcu:
  drm/fsl-dcu: use new drm_atomic_helper_shutdown
  drm/fsl-dcu: implement irq_preinstall/uninstall callbacks
  drm/fsl: Drop drm_vblank_cleanup

The series interleaves DRM and V4L2 patches due to dependencies between the R-
Car DU and VSP drivers. Mauro has acked all the V4L2 patches to go through
your tree, and they don't conflict with anything queued for v4.13 in his tree.
If I need to send any conflicting patches through Mauro's tree for v4.13, I'll
make sure to base them on this branch.

* 'drm/next/du' of git://linuxtv.org/pinchartl/media:
  drm: rcar-du: Map memory through the VSP device
  v4l: vsp1: Add API to map and unmap DRM buffers through the VSP
  v4l: vsp1: Map the DL and video buffers through the proper bus master
  v4l: rcar-fcp: Add an API to retrieve the FCP device
  v4l: rcar-fcp: Don't get/put module reference
  drm: rcar-du: Register a completion callback with VSP1
  v4l: vsp1: Extend VSP1 module API to allow DRM callbacks
  v4l: vsp1: Postpone frame end handling in event of display list race
  drm: rcar-du: Arm the page flip event after queuing the page flip

Merge tag 'sunxi-drm-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next

sun4i-drm changes for 4.13

An unusually big pull request for this merge window, with three notable
features:
  - V3s display engine support. This is especially notable because it uses
    a different display engine used on the newer Allwinner SoCs (H3, A64
    and the likes) that will be quite easily supported now.
  - HDMI support for the old Allwinner SoCs. This is enabled only on the
    A10s for now, but should be really easy to extend to deal with A10, A20
    and A31
  - Preliminary work to deal with dual-pipeline SoCs (A10, A20, A31, H3,
    etc.). It currently ignores the second pipeline, but we can use the
    dual-pipelines bindings. This will be useful to enable the display
    pipeline while we work on the dual-pipeline.

* tag 'sunxi-drm-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits)
  drm/sun4i: Add compatible for the A10s pipeline
  drm/sun4i: Add HDMI support
  dt-bindings: display: sun4i: Add allwinner,tcon-channel property
  dt-bindings: display: sun4i: Add HDMI display bindings
  drm/sun4i: Ignore the generic connectors for components
  drm/sun4i: tcon: multiply the vtotal when not in interlace
  drm/sun4i: tcon: Change vertical total size computation inconsistency
  drm/sun4i: tcon: Fix tcon channel 1 backporch calculation
  drm/sun4i: tcon: Switch mux on only for composite
  drm/sun4i: tcon: Move the muxing out of the mode set function
  drm/sun4i: tcon: Add channel debug
  drm/sun4i: tcon: add support for V3s TCON
  drm/sun4i: Add compatible string for V3s display engine
  drm/sun4i: add support for Allwinner DE2 mixers
  drm/sun4i: add a Kconfig option for sun4i-backend
  drm/sun4i: abstract a engine type
  drm/sun4i: return only planes for layers created
  dt-bindings: add bindings for DE2 on V3s SoC
  drm/sun4i: backend: Clarify sun4i_backend_layer_enable debug message
  drm/sun4i: Set TCON clock inside sun4i_tconX_mode_set
  ...

New radeon and amdgpu features for 4.13:
- Lots of Vega10 bug fixes
- Preliminary Raven support
- KIQ support for compute rings
- MEC queue management rework from Andres
- Audio support for DCE6
- SR-IOV improvements
- Improved module parameters for controlling radeon vs amdgpu support
  for SI and CIK
- Bug fixes
- General code cleanups

[airlied: dropped drmP.h header from one file was needed and build broke]

* 'drm-next-4.13' of git://people.freedesktop.org/~agd5f/linux: (362 commits)
  drm/amdgpu: Fix compiler warnings
  drm/amdgpu: vm_update_ptes remove code duplication
  drm/amd/amdgpu: Port VCN over to new SOC15 macros
  drm/amd/amdgpu: Port PSP v10.0 over to new SOC15 macros
  drm/amd/amdgpu: Port PSP v3.1 over to new SOC15 macros
  drm/amd/amdgpu: Port NBIO v7.0 driver over to new SOC15 macros
  drm/amd/amdgpu: Port NBIO v6.1 driver over to new SOC15 macros
  drm/amd/amdgpu: Port UVD 7.0 over to new SOC15 macros
  drm/amd/amdgpu: Port MMHUB over to new SOC15 macros
  drm/amd/amdgpu: Cleanup gfxhub read-modify-write patterns
  drm/amd/amdgpu: Port GFXHUB over to new SOC15 macros
  drm/amd/amdgpu: Add offset variant to SOC15 macros
  drm/amd/powerplay: add avfs control for Vega10
  drm/amdgpu: add virtual display support for raven
  drm/amdgpu/gfx9: fix compute ring doorbell index
  drm/amd/amdgpu: Rename KIQ ring to avoid spaces
  drm/amd/amdgpu: gfx9 tidy ups (v2)
  drm/amdgpu: add contiguous flag in ucode bo create
  drm/amdgpu: fix missed gpu info firmware when cache firmware during S3
  drm/amdgpu: export test ib debugfs interface
  ...

Cross-subsystem Changes:
- dt-bindings: add vendor prefix for NLT Technologies, Ltd. (Lucas)
- dt-bindings: Add support for samsung s6e3hf2 panel (Hoegeun)

Core Changes:
- Add drm_panel_bridge to avoid connector boilerplate in drivers (Eric)
- Trival fixes for dupe forward decl and reduce scope of variable (Dawid)

Driver Changes:
- dw-hdmi: Use mode_valid hook on bridge instead of connector (Jose)
- vc4,atmel-hlcdc: Use drm_panel_bridge where appropriate (Eric)
- panel: Add Innolux P079ZCA panel driver (Chris)
- panel-simple: Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels (Lucas)
- panel-samsung-s6e3ha2: Add s6e3hf2 panel support (Hoegeun)
- zte,vc4,pl111,panel,mxsfb: Miscellaneous fixes

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Chris Zhong <zyw@rock-chips.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Cc: Dawid Kurek <dawikur@gmail.com>

* tag 'drm-misc-next-2017-06-15' of git://anongit.freedesktop.org/git/drm-misc: (26 commits)
  drm: Reduce scope of 'state' variable
  drm: mxsfb_crtc: Reset the eLCDIF controller
  drm: Remove duplicate forward declaration
  drm/panel: s6e3ha2: Add support for s6e3hf2 panel on TM2e board
  dt-bindings: Add support for samsung s6e3hf2 panel
  drm/panel: add backlight dependency for sitronix-st7789v
  drm/panel: S6E3HA2 needs backlight code
  drm/panel: simple: add support for AUO P320HVN03
  drm/panel: simple: add support for NLT NL192108AC18-02D
  dt-bindings: add vendor prefix for NLT Technologies, Ltd.
  drm/panel: simple: add support for NEC NL12880B20-05
  drm/panel: add Innolux P079ZCA panel driver
  dt-bindings: Add INNOLUX P079ZCA panel bindings
  drm/vc4: Fix resource leak in 'vc4_get_hang_state_ioctl()' in error handling path
  drm/vc4/vc4_bo.c: always set bo->resv
  drm: Add const to name field declaration in struct drm_prop_enum_list
  drm/pl111: Fix offset calculation for the primary plane.
  drm/atmel-hlcdc: Fix panel registration
  drm/bridge: Build the panel wrapper in drm_kms_helper
  drm/atmel-hlcdc: Replace the panel usage with drm_panel_bridge.
  ...

Smaller scope reduces visibility of variable and makes usage of
uninitialized variable less possible.

Changes in v2:
	- separate declaration and initialization
Changes in v3:
	- add missing signed-off-by tag
Signed-off-by: NDawid Kurek <dawikur@gmail.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615174556.GA8872@gmail.com

According to the eLCDIF initialization steps listed in the MX6SX
Reference Manual the eLCDIF block reset is mandatory.

Without performing the eLCDIF reset the display shows garbage content
when the kernel boots.

In earlier tests this issue has not been observed because the bootloader
was previously showing a splash screen and the bootloader display driver
does properly implement the eLCDIF reset.

Add the eLCDIF reset to the driver, so that it can operate correctly
independently of the bootloader.

Tested on a imx6sx-sdb board.

Cc: <stable@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1494007301-14535-1-git-send-email-fabio.estevam@nxp.com

Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NHarish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

CPU and GPU paths were mostly the same.
Acked-by: NChristian König <christian.koenig@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NHarish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Allows reading/writing via SOC15 macros with offset for
various register banks.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NEric Huang <JinHuiEric.Huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Same as other asics.  If enabled, exposes a user selectable
number of virtual displays.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This got lost when the code was revamped.  Copy/paste bug from
gfx8.
Reported-by: NEvan Quan <evan.quan@amd.com>
Fixes: 78c16834 (drm/amdgpu: allow split of queues with kfd at queue granularity v4)
Reviewed-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Swap space for underscore in ring name.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

A couple of simple tidy ups to register programming.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

(v2): Avoid using 'data' uninitialized
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Under VF environment, the ucode would be settled to the visible VRAM,
As it would be pinned to the visible VRAM, it's better to add
contiguous flag,otherwise it need to move gpu address during the pin
process. This movement is not necessary.
Signed-off-by: Nhorchen <horace.chen@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

gpu_info firmware is released after data is used. But when system enters into
suspend, upper class driver will cache all firmware names. At that time,
gpu_info will be failing to load. It seems an upper class issue, that we should
not release gpu_info firmware until device finished.

[  903.236589] cache_firmware: amdgpu/vega10_sdma1.bin
[  903.236590] fw_set_page_data: fw-amdgpu/vega10_sdma1.bin buf=ffff88041eee10c0 data=ffffc90002561000 size=17408
[  903.236591] cache_firmware: amdgpu/vega10_sdma1.bin ret=0
[  903.464160] __allocate_fw_buf: fw-amdgpu/vega10_gpu_info.bin buf=ffff88041eee2c00
[  903.471815] (NULL device *): loading /lib/firmware/updates/4.11.0-custom/amdgpu/vega10_gpu_info.bin failed with error -2
[  903.482870] (NULL device *): loading /lib/firmware/updates/amdgpu/vega10_gpu_info.bin failed with error -2
[  903.492716] (NULL device *): loading /lib/firmware/4.11.0-custom/amdgpu/vega10_gpu_info.bin failed with error -2
[  903.503156] (NULL device *): direct-loading amdgpu/vega10_gpu_info.bin
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

As Christian and David's suggestion, submit the test ib ring debug interfaces.
It's useful for debugging with the command submission without VM case.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NEric Huang <JinHuiEric.Huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NEric Huang <JinHuiEric.Huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

No need to clear it.  The values are set explicitly.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Forward declarations in C are great but I'm pretty sure one is enough.
Signed-off-by: NDawid Kurek <dawikur@gmail.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170614213518.GA3554@gmail.com

This patch supports TM2e panel and the panel has 1600x2560 resolution
in 5.65" physical.

This identify panel type with compatibility string, also invoke
display mode that matches the type. So add the check code for s6e3ha2
compatibility and s6e3hf2 type and select the drm_display_mode of
default and edge type.
Signed-off-by: NHoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NInki Dae <inki.dae@samsung.com>
[treding@nvidia.com: fixup checkpatch warnings]
Signed-off-by: NThierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1492504836-19225-3-git-send-email-hoegeun.kwon@samsung.com

The samsung s6e3hf2 panel is a 5.65" 1600x2560 AMOLED panel connected
using MIPI-DSI interfaces.

The s6e3hf2 is add to samsung,s6e3ha2.txt binding because it is a
panel similar to the s6e3ha2. So add the compatible string and
comments.
Signed-off-by: NHoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1492504836-19225-2-git-send-email-hoegeun.kwon@samsung.com

Without the dependency, we run into a link error:

drivers/gpu/drm/panel/panel-sitronix-st7789v.o: In function `st7789v_probe':
panel-sitronix-st7789v.c:(.text.st7789v_probe+0xc0): undefined reference to `of_find_backlight_by_node'

Fixes: 7142afb3 ("drm/panel: Add driver for sitronix ST7789V LCD controller")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170419180326.303994-1-arnd@arndb.de

The new S6E3HA2 driver fails to link when backlight is disabled:

ERROR: "backlight_device_register" [drivers/gpu/drm/panel/panel-samsung-s6e3ha2.ko] undefined!
ERROR: "backlight_device_unregister" [drivers/gpu/drm/panel/panel-samsung-s6e3ha2.ko] undefined!

This adds a Kconfig dependency like we have it for some other panel drivers.

Fixes: ed29f942 ("drm/panel: Add support for S6E3HA2 panel driver on TM2 board")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170419175939.189098-2-arnd@arndb.de

This adds support for the AU Optronics Corporation 31.5"
FHD (1920x1080) LVDS TFT LCD panel, which can be supported
by the simple panel driver
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608180758.31020-4-l.stach@pengutronix.de