When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.

This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.

Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes it possible to use some more advanced queuing
techniques with this driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the following sequence:

	dma_set_mask(dev, mask);
	dma_set_coherent_mask(dev, mask);

with a call to the new helper dma_set_mask_and_coherent().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Without this patch b44 always allocates the 2 bytes needed for aligned
access on every platform, now it uses netdev_alloc_skb_ip_align().
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The nvram functions are exported and used by some normal drivers. To
prevent name clashes with ofter parts of the kernel code add a bcm47xx_
prefix in front of the function names and the header file name.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4744/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: NKevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit a1c7fff7 (net: netdev_alloc_skb() use build_skb()) broke b44 on
some 64bit machines.

It appears b44 and b43 use __netdev_alloc_skb() instead of alloc_skb()
for their bounce buffers.

There is no need to add an extra NET_SKB_PAD reservation for bounce
buffers :

- In TX path, NET_SKB_PAD is useless

- In RX path in b44, we force a copy of incoming frames if
  GFP_DMA allocations were needed.
Reported-and-bisected-by: NStefan Bader <stefan.bader@canonical.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WARNING: drivers/net/ethernet/broadcom/built-in.o(.init.text+0x5d): Section mismatch in reference from the function b44_init() to the function .exit.text:b44_pci_exit()

module exits with b44_cleanup()
Signed-off-by: NNikola Pajkovsky <n.pajkovsky@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported issues when using dev_kfree_skb() on UP systems and
systems with low numbers of cores.  dev_kfree_skb_irq() will
properly save IRQ state before freeing the skb.

Tested on 3.1.1 and 3.2_rc2

Example of reproducible trace of kernel 3.1.1
------------[ cut here ]------------
   WARNING: at kernel/softirq.c:159 local_bh_enable+0x32/0x79()
   ...
   Pid: 0, comm: swapper Not tainted 3.1.1-gentoo #1
   Call Trace:
    [<c1022970>] warn_slowpath_common+0x65/0x7a
    [<c102699e>] ? local_bh_enable+0x32/0x79
    [<c1022994>] warn_slowpath_null+0xf/0x13
    [<c102699e>] local_bh_enable+0x32/0x79
    [<c134bfd8>] destroy_conntrack+0x7c/0x9b
    [<c134890b>] nf_conntrack_destroy+0x1f/0x26
    [<c132e3a6>] skb_release_head_state+0x74/0x83
    [<c132e286>] __kfree_skb+0xb/0x6b
    [<c132e30a>] consume_skb+0x24/0x26
    [<c127c925>] b44_poll+0xaa/0x449
    [<c1333ca1>] net_rx_action+0x3f/0xea
    [<c1026a44>] __do_softirq+0x5f/0xd5
    [<c10269e5>] ? local_bh_enable+0x79/0x79
    <IRQ>  [<c1026c32>] ? irq_exit+0x34/0x8d
    [<c1003628>] ? do_IRQ+0x74/0x87
    [<c13f5329>] ? common_interrupt+0x29/0x30
    [<c1006e18>] ? default_idle+0x29/0x3e
    [<c10015a7>] ? cpu_idle+0x2f/0x5d
    [<c13e91c5>] ? rest_init+0x79/0x7b
    [<c15c66a9>] ? start_kernel+0x297/0x29c
    [<c15c60b0>] ? i386_start_kernel+0xb0/0xb7
   ---[ end trace 583f33bb1aa207a9 ]---
Signed-off-by: NXander Hover <LKML@hover.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.

CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Convert a printk with a static to pr_<level>_once
Add and use DRV_DESCRIPTION to reduce string duplication.
Remove now unused version.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

b44_tx() is run from softirq handler, it can use dev_kfree_skb() instead
of dev_kfree_skb_irq()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two functions in ssb are using register_pci_controller() which is
__devinit. The functions ssb_pcicore_init_hostmode() and
ssb_gige_probe() should also be __devinit.

This fixes the following warning:
WARNING: vmlinux.o(.text+0x2727b8): Section mismatch in reference from the function ssb_pcicore_init_hostmode() to the function .devinit.text:register_pci_controller()
The function ssb_pcicore_init_hostmode() references
the function __devinit register_pci_controller().
This is often because ssb_pcicore_init_hostmode lacks a __devinit
annotation or the annotation of register_pci_controller is wrong.

WARNING: vmlinux.o(.text+0x273398): Section mismatch in reference from the function ssb_gige_probe() to the function .devinit.text:register_pci_controller()
The function ssb_gige_probe() references
the function __devinit register_pci_controller().
This is often because ssb_gige_probe lacks a __devinit
annotation or the annotation of register_pci_controller is wrong.
Reported-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.

For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.

All drivers compiled with make allyesconfig ion x86_64 have been
updated.

Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().

All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code for the b44_wap54g10_workaround was never included, because
the config option was wrong. The nvram_get function was never in
mainline kernel, only in external OpenWrt patches.

The code should be compiled in when CONFIG_BCM47XX is selected and not
when CONFIG_SSB_DRIVER_MIPS is selected, because nvram_getenv is only
available on bcm47xx platforms and now in the mainline kernel code.
Using an include is better than a second function declaration, to fix
this when the function signature changes.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On resume, call request_irq() after resetting the hardware rather than
before. It's a shared interrupt so the handler could be called
immediately if another device on the same irq interrupts (and will be
called immediately if CONFIG_DEBUG_SHIRQ=y), but unless the hardware is
reinitialised with b44_init_hw() the read of the interrupt status
register will hang the system.
Signed-off-by: NJames Hogan <james@albanarts.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For carrier detection to work properly when binding the driver with a cable
unplugged, netif_carrier_off() should be called after register_netdev(),
not before.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a simplified version of the original patch from James Courtier-Dutton.

>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note that dma_sync_single_for_device and dma_sync_single_for_cpu support a
partial sync.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Gary Zambrano <zambrano@broadcom.com>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conversion in bf0dcbd9 missed the
new allocation in b44_rx.
This patch was used in OpenWRT for a long time.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do a PHY reset to test if there is an active phy and set the PHY address
to B44_PHY_ADDR_NO_PHY in case of an not active phy. This is needed for
the Linksys WRTSL54GS and Asus WL-500W.
This patch was used in OpenWRT for a long time.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>