This patch adds opcodes in thecompletion path that were
missed out earlier
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch will link the current allocated wrb with the next
 wrb that will be allocated. This is a requirement from the chip.
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

We need to hold on to ep resources untill invalidate and
  close connection are completed
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch enablesi be2iscsi to use the start number and number
 of cids/icd provided by FW rather than hard coded values.
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

converted using this script..

 perl -p -i -e 's|ulong32|u32|g' drivers/scsi/gdth*
 perl -p -i -e 's|ulong64|u64|g' drivers/scsi/gdth*
 perl -p -i -e 's|ushort|u16|g' drivers/scsi/gdth*
 perl -p -i -e 's|unchar|u8|g' drivers/scsi/gdth*
 perl -p -i -e 's|ulong|unsigned long|g' drivers/scsi/gdth*
 perl -p -i -e 's|PACKED|__attribute__((packed))|g' drivers/scsi/gdth*

sha1sum of the generated code was identical before and after.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Further to the lsml thread titled:
"does scsi_io_completion need to dump sense data for ata pass through (ck_cond =
1) ?"

This is a patch to skip logging when the sense data is
associated with a SENSE_KEY of "RECOVERED_ERROR" and the
additional sense code is "ATA PASS-THROUGH INFORMATION
AVAILABLE". This only occurs with the SAT ATA PASS-THROUGH
commands when CK_COND=1 (in the cdb). It indicates that
the sense data contains ATA registers.

Smartmontools uses such commands on ATA disks connected via
SAT. Periodic checks such as those done by smartd cause
nuisance entries into logs that are:
    - neither errors nor warnings
    - pointless unless the cdb that caused them are also logged
Signed-off-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The check on MAX_SCSI_TAR should be >= instead of > or we could go past the
end of the array.

Joe Eykholt aslo correctly points out that the check on MAX_LUN should be
>= as well.  That matches with how it is used in the rest of the file.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Stanse found that c3cn is poked many times around in
cxgb3i_conn_pdu_ready, there is no need to check if it is NULL.

Remove the test.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NKaren Xie <kxie@chelsio.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use kzalloc rather than kcalloc(1,...)

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The mac_esp PIO algorithm no longer works in 2.6.31 and crashes my Centris
660av. So here's a better one.

Also, force async with esp_set_offset() rather than esp_slave_configure().

One of the SCSI drives I tested still doesn't like the PIO mode and fails
with "esp: esp0: Reconnect IRQ2 timeout" (the same drive works fine in
PDMA mode).

This failure happens when esp_reconnect_with_tag() tries to read in two
tag bytes but the chip only provides one (0x20). I don't know what causes
this. I decided not to waste any more time trying to fix it because the
best solution is to rip out the PIO mode altogether and use the DMA
engine.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently dev_loss_tmo is capped by SCSI_DEVICE_BLOCK_MAX_TIMEOUT.
This causes problem with multipathing when the 'no_path_retry' setting
exceeds the dev_loss_tmo setting, as then the system might run into
a deadlock when all paths have been removed temporarily for longer
than dev_loss_tmo.
The principal reasons for the capping has been that we should
not allow a remote port to remain in status 'blocked' indefinitely,
so the capping is there to ensure that the port status is being reset
eventually.
However, the fast_io_fail_tmo will also move the remote port out of
the 'blocked' state, so for any HBA driver implementing both the
capping should really be on the fast_io_fail_tmo, and not on the
dev_loss_tmo.
This patch implements just that, ie the fast_io_fail_tmo is capped
to SCSI_DEVICE_BLOCK_TIMEOUT and the capping is removed from
dev_loss_tmo when fast_io_fail_tmo is set.
This allows us to synchronize the dev_loss_tmo setting to the
'no_path_retry' setting from multipathing thus avoiding the deadlock.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NJames Smart  <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Allows i == IM_MAX_HOSTS, which is out of range.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This allows i == MAX_INT_PARAM, which is out of range for ints[]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Allows i == MAX_INT_PARAM, which is out of range.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NBart Van Assche <bart.vanassche@gmail.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fixed a typo in libsrp.c: replaced two occurrences of 'RDAM' by 'RDMA'.
Signed-off-by: NBart Van Assche <bart.vanassche@gmail.com>
Acked-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The best way to fix this is to eliminate the intenal kmalloc() and
make the caller allocate the required amount of storage.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When removing several devices aic79xx will occasionally Oops
in ahd_handle_nonpkt_busfree during rescan. Looking at the
code I found that we're indeed not checking if the scb in
question is NULL. So check for it before accessing it.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The hardware used with zfcp cannot abort a currently pending CT or ELS
request. Therefore we need the option to postpone the timeout
triggered request abort within the fc layer, since there is nothing
zfcp can do to stop the request at this point.

Cc: James Smart <James.Smart@emulex.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The driver did not account for non-tape devices needing to employ
proper FCP2 recovery.  Driver now checks the FCP2-capable flag
only, rather than using a midlayer-determined flag (TYPE_TAPE).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Because of the terrible structuring of scsi-bidi-commands
it breaks some of the life time rules of a scsi-command.
It is now not allowed to free up the block-request before
cleanup and partial deallocation of the scsi-command. (Which
is not so for none bidi commands)

The right fix to this problem would be to make bidi command
a first citizen by allocating a scsi_sdb pointer at scsi command
just like cmd->prot_sdb. The bidi sdb should be allocated/deallocated
as part of the get/put_command (Again like the prot_sdb) and the
current decoupling of scsi_cmnd and blk-request should be kept.

For now make sure scsi_release_buffers() is called before the
call to blk_end_request_all() which might cause the suicide of
the block requests. At best the leak of bidi buffers, at worse
a crash, as there is a race between the existence of the bidi_request
and the free of the associated bidi_sdb.

The reason this was never hit before is because only OSD has the potential
of doing asynchronous bidi commands. (So does bsg but it is never used)
And OSD clients just happen to do all their bidi commands synchronously, up
until recently.

CC: Stable Tree <stable@kernel.org>
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

These particular problems were reported by Cisco and SAP and customers
as well. Cisco reported on RHEL4 U6 and SAP reported on SLES9 SP4 and
SLES10 SP2. We added these fixes on RHEL4 U6 and gave a private build
to IBM and Cisco. Cisco and IBM tested it for more than 15 days and
they reported that they did not see the issue so far. Before the fix,
Cisco used to see the issue within 5 days. We generated a patch for
SLES9 SP4 and SLES10 SP2 and submitted to Novell. Novell applied the
patch and gave a test build to SAP. SAP tested and reported that the
build is working properly.

We also tested in our lab using the tools "dishogsync", which is IO
stress tool and the tool was provided by Cisco.

Issue1:  File System going into read-only mode

Root cause: The driver tends to not free the memory (FIB) when the
management request exits prematurely. The accumulation of such
un-freed memory causes the driver to fail to allocate anymore memory
(FIB) and hence return 0x70000 value to the upper layer, which puts
the file system into read only mode.

Fix details: The fix makes sure to free the memory (FIB) even if the
request exits prematurely hence ensuring the driver wouldn't run out
of memory (FIBs).


Issue2: False Raid Alert occurs

When the Physical Drives and Logical drives are reported as deleted or
added, even though there is no change done on the system

Root cause: Driver IOCTLs is signaled with EINTR while waiting on
response from the lower layers. Returning "EINTR" will never initiate
internal retry.

Fix details: The issue was fixed by replacing "EINTR" with
"ERESTARTSYS" for mid-layer retries.
Signed-off-by: NPenchala Narasimha Reddy <ServeRAIDDriver@hcl.in>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

lpfc_hbadisc.c and lpfc_hw4.h accidentally got set executable.
Reported-by: NThomas Backlund <tmb@mandriva.org>
Cc: James Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).

This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: NBryn M. Reeves <bmr@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As noticed by Stephen Rothwell.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update Driver version to 8.3.7
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix discovery failures:
- Move all accesses to the fc_flag field inside the host lock.
- Restore link state after going through linkdown processing for FCF DEAD event.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix SCSI protocol related errors:
- Avoid I/O failures during EEH and HBA/CNA reset by correcting when
  we block the targets on the adapter.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix hardware/SLI relates issues:
- Fix CNA uses more than one EQ when in INTx interrupt mode.
- Fix driver tries to process failed read FCF record mailbox request.
- Fix allocating single receive buffer breaks FCoE receive queue.
- Support new read FCF record mailbox error case.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix NPIV operation errors:
- Fix vport not logging out of fabric when being deleted
- Fix vport fails to discover targets after devloss timeout.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix FC protocol errors:
- Fix multi-frame unsolicited sequences not queued properly
- Fix frames for unsolicited sequences not being associated with sequence.
- Fix unsolicited frame buffer sizes are not set properly
- Fix Sequence count for unsolicited frame headers not byte swapped.
- Fix Multi-frame sequence response frames go to wrong DID.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

During a manual scan, a user can send command to a nonexistent
lun, precisely at the point of max_lun. Normally it's possible
(but not required) that the firmware has the knowledge that it
is an invalid lun. In the particular case when max_lun is 256,
however, the nonexistent lun 256 will be confused with lun 0,
because the lun member in a request message is only u8, and 256
will become 0. So we need to fix the problem, at least, at the
driver level.
Signed-off-by: NEd Lin <ed.lin@promise.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix a target login issue, when parent interface is vlan and we are using cxgb3i sepecific
private ip address in '/etc/iscsi/ifaces/' iface file.
Acked-by: NKaren Xie <kxie@chelsio.com>
Signed-off-by: NRakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For a particular driver error condition, driver was doing double
scsi_dma_unmaps. Driver was calling scsi_dma_unmap in
pmcraid_error_handler and return 0. This pmcraid_error_handler is called
by pmcraid_io_done which will do scsi_dma_unmap again when it has
return 0 from pmcraid_error_handler.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added fundamental reset and pci save state.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Hold the hardware lock while do the response completion in work queue threads as
it involves sharing a common request queue among multiple threads.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>