Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.

In mmc_rescan(), the ->card_event() and the ->get_cd() callback are being
invoked without claiming the host, let's fix this.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ->card_event() callback may be called when re-scan is disabled and for
non-removable cards, which both cases are unnecessary.

Instead let's move the call later in mmc_rescan() where these constraints
have been validated.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".

This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.

A problem could occur with the existing RTC driver if:

A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
    ret = devm_request_threaded_irq()
comes before
    rtc->rtc_dev = devm_rtc_device_register();

In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call

    rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);

which in turn tries to access the unavailable rtc->rtc_dev.

The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.

This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: NJames Chen <james.chen@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 8520f380 ("USB: change hub initialization sleeps to
delayed_work") changed the hub_activate() routine to make part of it
run in a workqueue.  However, the commit failed to take a reference to
the usb_hub structure or to lock the hub interface while doing so.  As
a result, if a hub is plugged in and quickly unplugged before the work
routine can run, the routine will try to access memory that has been
deallocated.  Or, if the hub is unplugged while the routine is
running, the memory may be deallocated while it is in active use.

This patch fixes the problem by taking a reference to the usb_hub at
the start of hub_activate() and releasing it at the end (when the work
is finished), and by locking the hub interface while the work routine
is running.  It also adds a check at the start of the routine to see
if the hub has already been disconnected, in which nothing should be
done.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NAlexandru Cornea <alexandru.cornea@intel.com>
Tested-by: NAlexandru Cornea <alexandru.cornea@intel.com>
Fixes: 8520f380 ("USB: change hub initialization sleeps to delayed_work")
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The code expects the loop to end with "retries" set to zero but, because
it is a post-op, it will end set to -1.  I have fixed this by moving the
decrement inside the loop.

Fixes: 014aa2a3 ('USB: ipaq: minor ipaq_open() cleanup.')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Driver requested device firmware version string during probe using
only 24 byte long buffer. That buffer is too small for newer firmware
versions, which causes device firmware hang - device stops responding
to any commands after that. Increase buffer size to 128 which should
be enough for any current and future version strings.

Link: https://github.com/airspy/host/issues/27

Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: NBenjamin Vernoux <bvernoux@gmail.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Used Avago MGA-81563 RF amplifier could be destroyed pretty easily
with too strong signal or transmitting to bad antenna.
Add module parameter 'enable_rf_gain_ctrl' which allows enabling
RF gain control - otherwise, default without the module parameter,
RF gain control is set to 'grabbed' state which prevents setting
value to the control.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/usb/hackrf/hackrf.c:1533 hackrf_probe()
error: we previously assumed 'dev' could be null (see line 1366)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch broke ivtv logic, as reported at
 https://bugzilla.redhat.com/show_bug.cgi?id=1278942

This reverts commit 09290cc8.

Cc: stable@vger.kernel.org # for v4.1 and upper
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When allocating a pciback device fails, clear the private
field. This could lead to an use-after free, however
the 'really_probe' takes care of setting
dev_set_drvdata(dev, NULL) in its failure path (which we would
exercise if the ->probe function failed), so we we
are OK. However lets be defensive as the code can change.

Going forward we should clean up the pci_set_drvdata(dev, NULL)
in the various code-base. That will be for another day.
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reported-by: NJonathan Creekmore <jonathan.creekmore@gmail.com>
Signed-off-by: NDoug Goldstein <cardoe@cardoe.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

If CONFIG_BITREVERSE is not built-in, the sht15 driver fails to link:

drivers/built-in.o: In function `sht15_crc8':
drivers/hwmon/sht15.c:195: undefined reference to `byte_rev_table'

This adds a Kconfig 'select' statement, like all other users of
bitrev.h have it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 33836ee9 ("hwmon:change sht15_reverse()")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way")
teaches us that dealing with MSI-X can be troublesome.

Further checks in the MSI-X architecture shows that if the
PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we
may not be able to access the BAR (since they are memory regions).

Since the MSI-X tables are located in there.. that can lead
to us causing PCIe errors. Inhibit us performing any
operation on the MSI-X unless the MEMORY bit is set.

Note that Xen hypervisor with:
"x86/MSI-X: access MSI-X table only after having enabled MSI-X"
will return:
xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3!

When the generic MSI code tries to setup the PIRQ without
MEMORY bit set. Which means with later versions of Xen
(4.6) this patch is not neccessary.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Otherwise just continue on, returning the same values as
previously (return of 0, and op->result has the PIRQ value).

This does not change the behavior of XEN_PCI_OP_disable_msi[|x].

The pci_disable_msi or pci_disable_msix have the checks for
msi_enabled or msix_enabled so they will error out immediately.

However the guest can still call these operations and cause
us to disable the 'ack_intr'. That means the backend IRQ handler
for the legacy interrupt will not respond to interrupts anymore.

This will lead to (if the device is causing an interrupt storm)
for the Linux generic code to disable the interrupt line.

Naturally this will only happen if the device in question
is plugged in on the motherboard on shared level interrupt GSI.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Otherwise an guest can subvert the generic MSI code to trigger
an BUG_ON condition during MSI interrupt freeing:

 for (i = 0; i < entry->nvec_used; i++)
        BUG_ON(irq_has_action(entry->irq + i));

Xen PCI backed installs an IRQ handler (request_irq) for
the dev->irq whenever the guest writes PCI_COMMAND_MEMORY
(or PCI_COMMAND_IO) to the PCI_COMMAND register. This is
done in case the device has legacy interrupts the GSI line
is shared by the backend devices.

To subvert the backend the guest needs to make the backend
to change the dev->irq from the GSI to the MSI interrupt line,
make the backend allocate an interrupt handler, and then command
the backend to free the MSI interrupt and hit the BUG_ON.

Since the backend only calls 'request_irq' when the guest
writes to the PCI_COMMAND register the guest needs to call
XEN_PCI_OP_enable_msi before any other operation. This will
cause the generic MSI code to setup an MSI entry and
populate dev->irq with the new PIRQ value.

Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY
and cause the backend to setup an IRQ handler for dev->irq
(which instead of the GSI value has the MSI pirq). See
'xen_pcibk_control_isr'.

Then the guest disables the MSI: XEN_PCI_OP_disable_msi
which ends up triggering the BUG_ON condition in 'free_msi_irqs'
as there is an IRQ handler for the entry->irq (dev->irq).

Note that this cannot be done using MSI-X as the generic
code does not over-write dev->irq with the MSI-X PIRQ values.

The patch inhibits setting up the IRQ handler if MSI or
MSI-X (for symmetry reasons) code had been called successfully.

P.S.
Xen PCIBack when it sets up the device for the guest consumption
ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device).
XSA-120 addendum patch removed that - however when upstreaming said
addendum we found that it caused issues with qemu upstream. That
has now been fixed in qemu upstream.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The guest sequence of:

  a) XEN_PCI_OP_enable_msix
  b) XEN_PCI_OP_enable_msix

results in hitting an NULL pointer due to using freed pointers.

The device passed in the guest MUST have MSI-X capability.

The a) constructs and SysFS representation of MSI and MSI groups.
The b) adds a second set of them but adding in to SysFS fails (duplicate entry).
'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that
in a) pdev->msi_irq_groups is still set) and also free's ALL of the
MSI-X entries of the device (the ones allocated in step a) and b)).

The unwind code: 'free_msi_irqs' deletes all the entries and tries to
delete the pdev->msi_irq_groups (which hasn't been set to NULL).
However the pointers in the SysFS are already freed and we hit an
NULL pointer further on when 'strlen' is attempted on a freed pointer.

The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard
against that. The check for msi_enabled is not stricly neccessary.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The guest sequence of:

 a) XEN_PCI_OP_enable_msi
 b) XEN_PCI_OP_enable_msi
 c) XEN_PCI_OP_disable_msi

results in hitting an BUG_ON condition in the msi.c code.

The MSI code uses an dev->msi_list to which it adds MSI entries.
Under the above conditions an BUG_ON() can be hit. The device
passed in the guest MUST have MSI capability.

The a) adds the entry to the dev->msi_list and sets msi_enabled.
The b) adds a second entry but adding in to SysFS fails (duplicate entry)
and deletes all of the entries from msi_list and returns (with msi_enabled
is still set).  c) pci_disable_msi passes the msi_enabled checks and hits:

BUG_ON(list_empty(dev_to_msi_list(&dev->dev)));

and blows up.

The patch adds a simple check in the XEN_PCI_OP_enable_msi to guard
against that. The check for msix_enabled is not stricly neccessary.

This is part of XSA-157.

CC: stable@vger.kernel.org
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Double fetch vulnerabilities that happen when a variable is
fetched twice from shared memory but a security check is only
performed the first time.

The xen_pcibk_do_op function performs a switch statements on the op->cmd
value which is stored in shared memory. Interestingly this can result
in a double fetch vulnerability depending on the performed compiler
optimization.

This patch fixes it by saving the xen_pci_op command before
processing it. We also use 'barrier' to make sure that the
compiler does not perform any optimization.

This is part of XSA155.

CC: stable@vger.kernel.org
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The copy of the ring request was lacking a following barrier(),
potentially allowing the compiler to optimize the copy away.

Use RING_COPY_REQUEST() to ensure the request is copied to local
memory.

This is part of XSA155.

CC: stable@vger.kernel.org
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Since indirect descriptors are in memory shared with the frontend, the
frontend could alter the first_sect and last_sect values after they have
been validated but before they are recorded in the request.  This may
result in I/O requests that overflow the foreign page, possibly
overwriting local pages when the I/O request is executed.

When parsing indirect descriptors, only read first_sect and last_sect
once.

This is part of XSA155.

CC: stable@vger.kernel.org
Signed-off-by: NRoger Pau Monné <roger.pau@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

A compiler may load a switch statement value multiple times, which could
be bad when the value is in memory shared with the frontend.

When converting a non-native request to a native one, ensure that
src->operation is only loaded once by using READ_ONCE().

This is part of XSA155.

CC: stable@vger.kernel.org
Signed-off-by: NRoger Pau Monné <roger.pau@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Instead of open-coding memcpy()s and directly accessing Tx and Rx
requests, use the new RING_COPY_REQUEST() that ensures the local copy
is correct.

This is more than is strictly necessary for guest Rx requests since
only the id and gref fields are used and it is harmless if the
frontend modifies these.

This is part of XSA155.

CC: stable@vger.kernel.org
Reviewed-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The last from guest transmitted request gives no indication about the
minimum amount of credit that the guest might need to send a packet
since the last packet might have been a small one.

Instead allow for the worst case 128 KiB packet.

This is part of XSA155.

CC: stable@vger.kernel.org
Reviewed-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Commit 2910ff17
introduced a regression which would remove a recently added spare via
slot_store. Revert part of the patch which touches slot_store() and add
the disk directly using pers->hot_add_disk()

Fixes: 2910ff17 ("md: remove_and_add_spares() to activate specific
rdev")
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NPawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

The patch c7bfced9 committed to 4.4-rc
causes crash in LVM test shell/lvchange-raid.sh. The kernel crashes with
this BUG, the reason is that we attempt to suspend a device that is
already suspended. See also
https://bugzilla.redhat.com/show_bug.cgi?id=1283491

This patch fixes the bug by changing functions mddev_suspend and
mddev_resume to always nest.
The number of nested calls to mddev_nested_suspend is kept in the
variable mddev->suspended.
[neilb: made mddev_suspend() always nest instead of introduce mddev_nested_suspend]

kernel BUG at drivers/md/md.c:317!
CPU: 3 PID: 32754 Comm: lvm Not tainted 4.4.0-rc2 #1
task: 0000000047076040 ti: 0000000047014000 task.ti: 0000000047014000

     YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001000000000000001111 Not tainted
r00-03  000000000804000f 00000000102c5280 0000000010c7522c 000000007e3d1810
r04-07  0000000010c6f000 000000004ef37f20 000000007e3d1dd0 000000007e3d1810
r08-11  000000007c9f1600 0000000000000000 0000000000000001 ffffffffffffffff
r12-15  0000000010c1d000 0000000000000041 00000000f98d63c8 00000000f98e49e4
r16-19  00000000f98e49e4 00000000c138fd06 00000000f98d63c8 0000000000000001
r20-23  0000000000000002 000000004ef37f00 00000000000000b0 00000000000001d1
r24-27  00000000424783a0 000000007e3d1dd0 000000007e3d1810 00000000102b2000
r28-31  0000000000000001 0000000047014840 0000000047014930 0000000000000001
sr00-03  0000000007040800 0000000000000000 0000000000000000 0000000007040800
sr04-07  0000000000000000 0000000000000000 0000000000000000 0000000000000000

IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000102c538c 00000000102c5390
 IIR: 03ffe01f    ISR: 0000000000000000  IOR: 00000000102b2748
 CPU:        3   CR30: 0000000047014000 CR31: 0000000000000000
 ORIG_R28: 00000000000000b0
 IAOQ[0]: mddev_suspend+0x10c/0x160 [md_mod]
 IAOQ[1]: mddev_suspend+0x110/0x160 [md_mod]
 RP(r2): raid1_add_disk+0xd4/0x2c0 [raid1]
Backtrace:
 [<0000000010c7522c>] raid1_add_disk+0xd4/0x2c0 [raid1]
 [<0000000010c20078>] raid_resume+0x390/0x418 [dm_raid]
 [<00000000105833e8>] dm_table_resume_targets+0xc0/0x188 [dm_mod]
 [<000000001057f784>] dm_resume+0x144/0x1e0 [dm_mod]
 [<0000000010587dd4>] dev_suspend+0x1e4/0x568 [dm_mod]
 [<0000000010589278>] ctl_ioctl+0x1e8/0x428 [dm_mod]
 [<0000000010589518>] dm_compat_ctl_ioctl+0x18/0x68 [dm_mod]
 [<0000000040377b88>] compat_SyS_ioctl+0xd0/0x1558

Fixes: c7bfced9 ("md: suspend i/o during runtime blk_integrity_unregister")
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

Neil pointed out setting journal disk role to raid_disks will confuse
reshape if we support reshape eventually. Switching the role to 0 (we
should be fine as long as the value >=0) and skip sysfs file creation to
avoid error.
Signed-off-by: NShaohua Li <shli@fb.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

The commit c31df25f ("md/raid10: make sync_request_write() call
bio_copy_data()") replaced manual data copying with bio_copy_data() but
it doesn't work as intended. The source bio (fbio) is already processed,
so its bvec_iter has bi_size == 0 and bi_idx == bi_vcnt.  Because of
this, bio_copy_data() either does not copy anything, or worse, copies
data from the ->bi_next bio if it is set.  This causes wrong data to be
written to drives during resync and sometimes lockups/crashes in
bio_copy_data():

[  517.338478] NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [md126_raid10:3319]
[  517.347324] Modules linked in: raid10 xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter ip_tables x86_pkg_temp_thermal coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul cryptd shpchp pcspkr ipmi_si ipmi_msghandler tpm_crb acpi_power_meter acpi_cpufreq ext4 mbcache jbd2 sr_mod cdrom sd_mod e1000e ax88179_178a usbnet mii ahci ata_generic crc32c_intel libahci ptp pata_acpi libata pps_core wmi sunrpc dm_mirror dm_region_hash dm_log dm_mod
[  517.440555] CPU: 0 PID: 3319 Comm: md126_raid10 Not tainted 4.3.0-rc6+ #1
[  517.448384] Hardware name: Intel Corporation PURLEY/PURLEY, BIOS PLYDCRB1.86B.0055.D14.1509221924 09/22/2015
[  517.459768] task: ffff880153773980 ti: ffff880150df8000 task.ti: ffff880150df8000
[  517.468529] RIP: 0010:[<ffffffff812e1888>]  [<ffffffff812e1888>] bio_copy_data+0xc8/0x3c0
[  517.478164] RSP: 0018:ffff880150dfbc98  EFLAGS: 00000246
[  517.484341] RAX: ffff880169356688 RBX: 0000000000001000 RCX: 0000000000000000
[  517.492558] RDX: 0000000000000000 RSI: ffffea0001ac2980 RDI: ffffea0000d835c0
[  517.500773] RBP: ffff880150dfbd08 R08: 0000000000000001 R09: ffff880153773980
[  517.508987] R10: ffff880169356600 R11: 0000000000001000 R12: 0000000000010000
[  517.517199] R13: 000000000000e000 R14: 0000000000000000 R15: 0000000000001000
[  517.525412] FS:  0000000000000000(0000) GS:ffff880174a00000(0000) knlGS:0000000000000000
[  517.534844] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  517.541507] CR2: 00007f8a044d5fed CR3: 0000000169504000 CR4: 00000000001406f0
[  517.549722] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  517.557929] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  517.566144] Stack:
[  517.568626]  ffff880174a16bc0 ffff880153773980 ffff880169356600 0000000000000000
[  517.577659]  0000000000000001 0000000000000001 ffff880153773980 ffff88016a61a800
[  517.586715]  ffff880150dfbcf8 0000000000000001 ffff88016dd209e0 0000000000001000
[  517.595773] Call Trace:
[  517.598747]  [<ffffffffa043ef95>] raid10d+0xfc5/0x1690 [raid10]
[  517.605610]  [<ffffffff816697ae>] ? __schedule+0x29e/0x8e2
[  517.611987]  [<ffffffff814ff206>] md_thread+0x106/0x140
[  517.618072]  [<ffffffff810c1d80>] ? wait_woken+0x80/0x80
[  517.624252]  [<ffffffff814ff100>] ? super_1_load+0x520/0x520
[  517.630817]  [<ffffffff8109ef89>] kthread+0xc9/0xe0
[  517.636506]  [<ffffffff8109eec0>] ? flush_kthread_worker+0x70/0x70
[  517.643653]  [<ffffffff8166d99f>] ret_from_fork+0x3f/0x70
[  517.649929]  [<ffffffff8109eec0>] ? flush_kthread_worker+0x70/0x70
Signed-off-by: NArtur Paszkiewicz <artur.paszkiewicz@intel.com>
Reviewed-by: NShaohua Li <shli@kernel.org>
Cc: stable@vger.kernel.org (v4.2+)
Fixes: c31df25f ("md/raid10: make sync_request_write() call bio_copy_data()")
Signed-off-by: NNeilBrown <neilb@suse.com>

Currently the Tx flow control is based on reading the hardware state,
which is not accurate since it may not reflect the descriptors that
are not yet reached the memory.

To accurately control the Tx flow, changing it to be software based.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit e20538b8
("gpio: Propagate errors from chip->get()")
started to propagate errors from the .get() functions since
we can get errors from the infrastructure of e.g. slowbus
GPIO expanders.

However it turns out a bunch of drivers relied on the core
to clamp the value, so we need to revert to the old behaviour
and go over all drivers and fix them to conform to the
expectations of the core before we go back to propagating
the error code.

Cc: stable@vger.kernel.org # 4.3+
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Fixes: e20538b8 ("gpio: Propagate errors from chip->get()")
Reported-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The bgpio_get_set() call should return a value clamped to [0,1],
the current code will return a negative value if reading
bit 31, which turns the value negative as this is a signed value
and thus gets interpreted as an error by the gpiolib core.
Found on the gpio-mxc but applies to any MMIO driver.

Cc: stable@vger.kernel.org # 4.3+
Cc: kernel@pengutronix.de
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Fixes:  e20538b8 ("gpio: Propagate errors from chip->get()")
Reported-by: NClemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The patch fixes FCC port lock-up, which occurs as a result of a bug
during underrun/collision handling. Within the tx_startup() function
in mac-fcc.c, the address of last BD is not calculated correctly.
As a result of wrong calculation of the last BD address, the next
transmitted BD may be set to an area out of the transmit BD ring.
This actually causes to port lock-up and it is not recoverable.
Signed-off-by: NMartin Roth <martin.roth@motorolasolutions.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 15bf176d ("gianfar: Don't enable the Filer w/o the
Parser"), 'TSEC' model controllers (for example as seen on MPC8541E)
always have 8 bytes stripped from the front of received frames.
Only 'eTSEC' gianfar controllers have the RX Filer capability (amongst
other enhancements). Previously this was treated as always enabled
for both 'TSEC' and 'eTSEC' controllers.
In commit 15bf176d ("gianfar: Don't enable the Filer w/o the Parser")
a subtle change was made to the setting of 'uses_rxfcb' to effectively
always set it (since 'rx_filer_enable' was always true). This had the
side-effect of always stripping 8 bytes from the front of received frames
on 'TSEC' type controllers.

We now only enable the RX Filer capability on controller types that
support it, thereby avoiding the issue for 'TSEC' type controllers.
Reviewed-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: NMark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: NHamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix parent-device reference leak due to SPI-core taking an unnecessary
reference to the parent when allocating the master structure, a
reference that was never released.

Note that driver core takes its own reference to the parent when the
master device is registered.

Fixes: 49dce689 ("spi doesn't need class_device")
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

We use the spi_lock spinlock to protect against races between the device
being removed and file operations on the spidev.  This means that in the
removal path all references to the device need to be done under lock as
in removal we dropping references to the device.
Reported-by: NVegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: NMark Brown <broonie@kernel.org>