RSS context allocation and RSS indirection table setup are very different
on the new chip.  Refactor bnxt_setup_vnic() to call 2 different functions
to set up RSS for the vnic based on chip type.  On the new chip, the
number of RSS contexts and the indirection table size depends on the
number of RX rings.  Each indirection table entry is also different
on the new chip since ring groups are no longer used.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the new 57500 chips, we need to allocate one RSS context for every
64 RX rings.  In previous chips, only one RSS context per vnic is
required regardless of the number of RX rings.  So increase the max
RSS context array count to 8.

Hardware ring groups are not used on the new chips.  Note that the
software ring group structure is still maintained in the driver to
keep track of the rings associated with the vnic.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the new 57500 chips, we allocate/free one CP ring for each RX ring or
TX ring separately.  Using separate CP rings for RX/TX is an improvement
as TX events will no longer be stuck behind RX events.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware ring allocation semantics are slightly different for most
ring types on 57500 chips.  Allocation/deallocation for NQ rings are
also added for the new chips.

A CP ring handle is also added so that from the NQ interrupt event,
we can locate the CP ring.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the new 57500 chips, getting the associated CP ring ID associated with
an RX ring or TX ring is different than before.  On the legacy chips,
we find the associated ring group and look up the CP ring ID.  On the
57500 chips, each RX ring and TX ring has a dedicated CP ring even if
they share the MSIX.  Use these helper functions at appropriate places
to get the CP ring ID.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 57500 chips, the original bnxt_cp_ring_info struct now refers to the
NQ.  bp->cp_nr_rings refer to the number of NQs on 57500 chips.  There
are now 2 pointers for the CP rings associated with RX and TX rings.
Modify bnxt_alloc_cp_rings() and bnxt_free_cp_rings() accordingly.

With multiple CP rings per NAPI, we need to add a pointer in
bnxt_cp_ring_info struct to point back to the bnxt_napi struct.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ring reservation functions have to be modified for P5 chips in the
following ways:

- bnxt_cp_ring_info structs map to internal NQs as well as CP rings.
- Ring groups are not used.
- 1 CP ring must be available for each RX or TX ring.
- number of RSS contexts to reserve is multiples of 64 RX rings.
- RFS currently not supported.

Also, RX AGG rings are only used for jumbo frames, so we need to
unconditionally call bnxt_reserve_rings() in __bnxt_open_nic()
to see if we need to reserve AGG rings in case MTU has changed.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store the maximum MSIX capability in PCIe config. space earlier.  When
we call firmware to query capability, we need to compare the PCIe
MSIX max count with the firmware count and use the smaller one as
the MSIX count for 57500 (P5) chips.

The new chips don't use ring groups.  But previous chips do and
the existing logic limits the available rings based on resource
calculations including ring groups.  Setting the max ring groups to
the max rx rings will work on the new chips without changing the
existing logic.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 57500 series chips have a new 64-bit doorbell format.  Use a new
bnxt_db_info structure to unify the new and the old 32-bit doorbells.
Add a new bnxt_set_db() function to set up the doorbell addreses and
doorbell keys ahead of time.  Modify and introduce new doorbell
helpers to help abstract and unify the old and new doorbells.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

57500 series is a new chip class (P5) that requires some driver changes
in the next several patches.  This adds basic chip ID, doorbells, and
the notification queue (NQ) structures.  Each MSIX is associated with an
NQ instead of a CP ring in legacy chips.  Each NQ has up to 2 associated
CP rings for RX and TX.  The same bnxt_cp_ring_info struct will be used
for the NQ.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call firmware to configure the DMA addresses of all context memory
pages on new devices requiring context memory.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New device requires host context memory as a backing store.  Call
firmware to check for context memory requirements and store the
parameters.  Allocate host pages accordingly.

We also need to move the call bnxt_hwrm_queue_qportcfg() earlier
so that all the supported hardware queues and the IDs are known
before checking and allocating context memory.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer chips require the PTU_PTE_VALID bit to be set for every page
table entry for context memory and rings.  Additional bits are also
required for page table entries for all rings.  Add a flags field to
bnxt_ring_mem_info struct to specify these additional bits to be used
when setting up the pages tables as needed.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the DMA page table and vmem fields in bnxt_ring_struct to a new
bnxt_ring_mem_info struct.  This will allow context memory management
for a new device to re-use some of the existing infrastructure.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware spec. allows interrupt coalescing parameters, such as
maximums, timer units, supported features to be queried.  Update
the driver to make use of the new call to query these parameters
and provide the legacy defaults if the call is not available.

Replace the hard-coded values with these parameters.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the max_ext_req_len field from the HWRM_VER_GET_RESPONSE.
If this field is valid and greater than the mailbox size, use the
short command format to send firmware messages greater than the
mailbox size.  Newer devices use this method to send larger messages
to the firmware.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Latest firmware spec. has some additional rx extended port stats and new
tx extended port stats added.  We now need to check the size of the
returned rx and tx extended stats and determine how many counters are
valid.  New counters added include CoS byte and packet counts for rx
and tx.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.

If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.

Fixes: 30f52947 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.

This patch fixes the problem described above.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs.  This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs.  DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.

Fixes: 674f50a5 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events.  bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting.  In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.

We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.

Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: NSong Liu <songliubraving@fb.com>
Reviewed-by: NSong Liu <songliubraving@fb.com>
Tested-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older.  This
will cause the VF driver to fail during probe:

  bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
  bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
  bnxt_en 0000:00:03.0: Unable to initialize mac address.
  bnxt_en: probe of 0000:00:03.0 failed with error -99

We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.

Fixes: 707e7e96 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: NSeth Forshee <seth.forshee@canonical.com>
Reported-by: NSiwei Liu <loseweigh@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA.  There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA.  This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.

To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.

Fixes: ec86f14e ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused bnxt_subtract_ulp_resources().  Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0.  This will properly setup the
init sequence to initialize the default rings again.  We also need
to signal the RDMA driver to stop and clear its interrupts.  We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.

Fixes: 25e1acd6 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 114878 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CNP CoS queue is reserved for internal RDMA Congestion Notification
Packets (CNP) and should not be used for a TC.  Modify the CoS queue
discovery code to skip over the CNP CoS queue and to reduce
bp->max_tc accordingly.  However, if RDMA is disabled in NVRAM, the
the CNP CoS queue can be used for a TC.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export temperature sensor reading via hwmon sysfs.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flags field is almost getting full.  Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect.  Define a macro to perform
this check.
Signed-off-by: NMichael Chan <michael.chan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec.  With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets.  But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example  The PF driver
will provision guaranteed minimum resources of 0.  Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During hotplug, the driver's open function can be called almost
immediately after power on reset.  The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings.  Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hwrm_dbg_resp_addr and hwrm_dbg_resp_dma_addr are never used
and can be removed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bug in the error code path when bnxt_request_irq() returns failure.
bnxt_disable_napi() should not be called in this error path because
NAPI has not been enabled yet.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed.  The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L.  If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly.  This
problem shows up on VFs with very small number of MSIX.

There is no other logic that relies on the IRQ count excluding the ones
used by RDMA.  So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.

Fixes: a588e458 ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the driver assumes IFF_BROADCAST is always set and always sets
the broadcast filter.  Modify the code to set or clear the broadcast
filter according to the IFF_BROADCAST flag.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>