This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 38ae92dc "fec: Add support for reading
RMON registers" causes the imx6Q to crash.

This fixes it by only enabling the RMON registers, the
registers are already cleared by the MAC being reset.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tx_bytes field was not being updated so the
network card statistics showed 0.0B transmitted.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: NChristoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool operation to read RMON registers.

Tested against net-next on i.MX28.

v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.

fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)

Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.

Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool operation to restart autonegotiation via the PHY.

Tested on i.MX28EVK.
Signed-off-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 75096579 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
CC: netdev@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to save power, let's disable the regulator in the suspend function and
enable it in resume.

Tested on a mx28evk board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During probe the clocks are enabled prior than the acquiring the interrupts.

In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case of error during probe, disable the PHY regulator.

Do the same in fec_drv_remove().
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.

This is wrong because at this point the interrupts have not even been acquired.

Swap failed_init/failed_irq to fix the error path.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().

This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the standard DIV_ROUND_UP macro in order to provide better readability.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MVF is a family while MVF600 is a particular SoC in the family.  We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device.  And this is how fec_dt_ids
works for all those IMX fec variants.  Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug cable many times")
introduced the following 'if' block in the beginning of fec_start():

	if (netif_running(ndev)) {
		netif_device_detach(ndev);
		napi_disable(&fep->napi);
		netif_stop_queue(ndev);
		netif_tx_lock_bh(ndev);
	}

Then later in the end of fec_restart() there is another block that calls the
opposite of each one of these functions.

The correct approach would be to also call them with in the reverse order, so
that we have as result:

	if (netif_running(ndev)) {
		netif_tx_unlock_bh(ndev);
		netif_wake_queue(ndev);
		napi_enable(&fep->napi);
		netif_device_attach(ndev);
	}
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_restart() runs in softirq context and we should use the
netif_tx_lock_bh/netif_tx_unlock_bh() variants to avoid the following warning
that happens since commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug
cable many times"):

[    9.753168] =================================
[    9.757540] [ INFO: inconsistent lock state ]
[    9.761921] 3.10.0-rc1-next-20130514 #13 Not tainted
[    9.766897] ---------------------------------
[    9.771264] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    9.777288] swapper/0 [HC0[0]:SC1[3]:HE1:SE0] takes:
[    9.782261]  (_xmit_ETHER#2){+.?...}, at: [<c03c24a4>] sch_direct_xmit+0xa0/0x2d4
[    9.789879] {SOFTIRQ-ON-W} state was registered at:
[    9.794769]   [<c0059c60>] __lock_acquire+0x528/0x1bc0
[    9.799953]   [<c005b838>] lock_acquire+0xa0/0x108
[    9.804780]   [<c0441320>] _raw_spin_lock+0x28/0x38
[    9.809702]   [<c02f9fc8>] fec_restart+0x5d0/0x664
[    9.814542]   [<c02fa738>] fec_enet_adjust_link+0xa8/0xc0
[    9.819978]   [<c02f7a28>] phy_state_machine+0x2fc/0x370
[    9.825323]   [<c0035ee0>] process_one_work+0x1c0/0x4a0
[    9.830589]   [<c0036594>] worker_thread+0x138/0x394
[    9.835587]   [<c003c620>] kthread+0xa4/0xb0
[    9.839890]   [<c000e820>] ret_from_fork+0x14/0x34
[    9.844728] irq event stamp: 185984
[    9.848226] hardirqs last  enabled at (185984): [<c00232b0>] local_bh_enable_ip+0x84/0xf0
[    9.856450] hardirqs last disabled at (185983): [<c0023270>] local_bh_enable_ip+0x44/0xf0
[    9.864667] softirqs last  enabled at (185966): [<c0023470>] irq_enter+0x64/0x68
[    9.872099] softirqs last disabled at (185967): [<c0023510>] irq_exit+0x9c/0xd8
[    9.879440]
[    9.879440] other info that might help us debug this:
[    9.885981]  Possible unsafe locking scenario:
[    9.885981]
[    9.891912]        CPU0
[    9.894364]        ----
[    9.896814]   lock(_xmit_ETHER#2);
[    9.900259]   <Interrupt>
[    9.902884]     lock(_xmit_ETHER#2);
[    9.906500]
[    9.906500]  *** DEADLOCK ***
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants.  This is inappropriate, because some variants like imx5 have
no such support on hardware.  Consequently, fec is broken on these
platforms.  Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

reproduce steps
 1. flood ping from other machine
 	ping -f -s 41000 IP
 2. run below script
    while [ 1 ]; do ethtool -s eth0 autoneg off;
    sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;

You can see oops in one hour.

The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.

Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.

The feature is enabled by default but can be
enabled/disabled by ethtool.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is nothing in the driver that requires <asm/coldfire.h> and
<asm/mcfsim.h>.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.

Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging message style.

Convert the printks where a struct net_device is available to
netdev_<level>.  Convert the other printks to pr_<level> and
add pr_fmt where appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when booting a mx6 device we get the following on boot:

registered PHC device on eth%d

Fix it by printing the network device name only after it gets registered, so
that the following can be read now:

fec 2188000.ethernet eth0: registered PHC device 0
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freescale Vybrid platform implentments MAC-ENET core
providing compatibility with half- or full-duplex
10/100 Mbit/s Ethernet LANs.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since of_get_mac_address() is now defined even if CONFIG_OF_NET
is not configured, the ifdef around the code calling it is no longer
necessary and can be removed.

Similar, since of_get_phy_mode() is now defined as dummy function
if OF_NET is not configured, it is no longer necessary to provide
an OF dependent function as front-end. Also, the function depends
on OF_NET, not on OF, so the conditional code was not correct anyway.
Drop the front-end function and call of_get_phy_mode() directly.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TX Buffer in fec_enet_alloc_buffers was being initialized
with the receive register define BD_ENET_RX_INT instead of
the transmit register define BD_ENET_TX_INT
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_ptp.ko can't run individually
rename fec.c to fec_main.c
Build fec.o and fec_ptp.o into one fec.ko
Remove unnessary EXPORT_SYMBOL in fec_ptp
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_poll_controller() was not declared. It should be static.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following warnings that happen when building with W=1 option:

drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_free_buffers':
drivers/net/ethernet/freescale/fec.c:1337:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_alloc_buffers':
drivers/net/ethernet/freescale/fec.c:1361:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_init':
drivers/net/ethernet/freescale/fec.c:1631:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit dc975382 introduces napi support
but never calls napi_disable. This will generate a kernel oops
(kernel BUG at include/linux/netdevice.h:473!) every time, when
ndo_stop is called followed by ndo_start.
Add the missing napi_diable call.
Signed-off-by: NGeorg Hofmann <georg@hofmannsweb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.

Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI header is not needed, so get rid of it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.

Other trivial changes around these removals:

Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>