The ir_input_dev gets filled in by __ir_input_register, the one
allocated in mceusb_init_input_dev was being overwritten by the correct
one shortly after it was initialized (ultimately resulting in a memory
leak). This bug was inherited from imon.c, and was pointed out to me by
Maxim Levitsky.

v2: fix incorrect dev arg to dev_dbg
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The ir_input_dev gets filled in by __ir_input_register, the one
allocated in imon_init_idev was being overwritten by the correct one
shortly after it was initialized (ultimately resulting in a memory
leak). Additionally, there was an ill-advised memcpy into that
extraneous ir_input_dev which gets fixed by this.

Ill-advised memcpy pointed out by Dmitry Torokhov, bad usage of
ir_input_dev pointed out by Maxim Levitsky.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Per Dmitry Torokhov, following input_unregister_device with an
input_free_device is forbidden, the former is sufficient alone.
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The CX23885 and CX25840 modules were using their own simple
IR pulse width measurement record type which required conversion
when passing to the new IR core.  This change makes that record type
consistent with the new IR core and removes a data conversion.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of reporting an IR Rx timeout event as a ridiculously
long space, report it as a space of the lenght of the timeout.

This partially fixes operation with LIRC without breaking
interoperation with the in kernel decoders.  The gaps lengths
reported to LIRC are still not real however.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Compute and report the maximum IR pulse measurment width, even
if we are set to perform carrier modulation or demodulation and
the number is fixed by the carrier freq.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver no longer depends on the old IR functions selected by
VIDEO_IR.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The CX23885 IR controller was reported to cause an interrupt storm
on a TeVii S470 card, but was reported fine on an HVR-1250.  Keep
integrated IR disabled by default on CX2388[57] based cards to avoid
a bad user experience in the general case.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Interrupts from the AV Core are best handled by a workqueue handler
since many I2C transactions are required to service the AV Core
interrupt.  The AV_CORE PCI interrupt is disabled by the IRQ handler
and reenabled when the work handler is finished.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch encapsulates access to the PCI_INT_MSK register and
dev->pci_irqmask variable and protects them with a spinlock.
This is needed because both the hard IRQ handler and a workhandler
will need to manipulate the mask to disable the AV_CORE interrupt.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add initial IR Rx support using the intergrated IR controller in the
A/V core of the CX23885 bridge chip.

This initial support is flawed in that I2C transactions should not
be performed in a hard irq context.  That will be fixed in a
follow on patch.

The TeVii S470 support is reported to generate perptual interrupts
that renders a user' system nearly unusable.  The TeVii S470 IR
will be disabled by default in a follow on patch.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch is primarily a port of the integrated IR controller code in
cx23885/cx23888-ir.c.  Right now, only the CX2388[57] AV core will
really try to set up IR. This IR support, by design, still requires the
bridge driver to do final IO pin mux configuration and setup of the IR
controller parameters.

For the CX2388[578] chips, enabling the AV Core for IR also starts
sending Audio and Video interrupts to the bridge driver.  For
CX2388[578] chips audio and video interrupts are ignored and
acknowledged when they happen.

IR interrupt handling and status logging is exluded for the CX23888
which does not have an IR controller on the AV core.

Note that experimentation reveals that the IR irq enables on the
CX23885 have an inverted logic sense.  The CX23887 likely suffers from
the same quirk.  For these chips, those irq enable bits are handled
as interrupt disables.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources.  Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block.  This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Explicitly configure the IR Tx and IR Rx pins to be driven by the
IR Rx and Tx pads from the AV core for CX23888 IR.

For the HVR-1850 and HVR-1290 configure the IR Tx level inversion,
so the Tx LED is off when idle.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters.  This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a method to v4l2_sudev_core_ops to allow bridge drivers to
manage what signal pads/functions are routed out to multiplexed IO pins on a
pin by pin basis.  The interface also allows specifying initial output settings
for pins and disabling an IO pin altogether.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a simple log_status function for raw analog video capture device nodes,
to provide insight into the state of the CX2388[578] A/V decoder core.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0
vs. the standard 0x80.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There was a small window between writing the cx25840 register
address over the i2c bus and reading the register contents back from the
cx25840 device that the i2c adapter lock was released.  This change ensures the
adapter lock is not released until the register read is done.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Function i2c_wait_done() never returns negative values, so there is no
point in checking for them.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't just check for nacks on zero-length transactions. Check on
other transactions too.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Documentation/i2c/fault-codes says that i2c adapter drivers should
return -ENXIO when no slave acks an address byte.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On laptops, the webcam sometimes disconnects when writing the first main
register (b300). This patch prevents the creation of a new /dev/video<n>
on streaming start.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The added controls are exposure, gain, autogain and backlight compensation.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The JPEG format did not work fine. The Bayer format offers correct VGA (640x480)
resolution, but bad QQVGA (160x120). This last resolution is removed.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The bit 7 of the sensor gain register multiplies the 7bits value by two.
It is now always set with half the user gain value.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The start_1 exchange must be done by (reg, val) * 5 and not 8.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The sensor enum definition was not at the right place.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: check kmalloc() result
  arch/tile: catch up on various minor cleanups.
  arch/tile: avoid erroneous error return for PTRACE_POKEUSR.
  tile: set ARCH_KMALLOC_MINALIGN
  tile: remove homegrown L1_CACHE_ALIGN macro
  arch/tile: Miscellaneous cleanup changes.
  arch/tile: Split the icache flush code off to a generic <arch> header.
  arch/tile: Fix bug in support for atomic64_xx() ops.
  arch/tile: Shrink the tile-opcode files considerably.
  arch/tile: Add driver to enable access to the user dynamic network.
  arch/tile: Enable more sophisticated IRQ model for 32-bit chips.
  Move list types from <linux/list.h> to <linux/types.h>.
  Add wait4() back to the set of <asm-generic/unistd.h> syscalls.
  Revert adding some arch-specific signal syscalls to <linux/syscalls.h>.
  arch/tile: Do not use GFP_KERNEL for dma_alloc_coherent(). Feedback from fujita.tomonori@lab.ntt.co.jp.
  arch/tile: core support for Tilera 32-bit chips.
  Fix up the "generic" unistd.h ABI to be more useful.

* 'for-linus' of git://www.jni.nu/cris: (51 commits)
  CRIS: Fix alignment problem for older ld
  CRIS: Always dump registers for segfaulting process.
  CRIS: Add config for pausing a seg-faulting process
  CRIS: Don't take faults while in_atomic
  CRIS: Fixup lookup for delay slot faults
  CRIS: Discard exit.text and .data at runtime
  CRIS: Add cache aligned and read mostly data sections
  CRIS: Return something from profile write
  CRIS: Add ARTPEC-3 and timestamps for sync-serial
  CRIS: Better ARTPEC-3 support for gpio
  CRIS: Add include guard
  CRIS: Better handling of pinmux settings
  CRIS: New DMA defines for ARTPEC-3
  CRIS: __do_strncpy_from_user: Don't read the byte beyond the nil
  CRIS: Pagetable for ARTPEC-3
  CRIS: Machine dependent memmap.h
  CRIS: Check if pointer is set before using it
  CRIS: Machine dependent dma.h
  CRIS: Define __read_mostly for CRISv32
  CRIS: Discard .note.gnu.build-id section
  ...

* 'for-linus' of git://android.kernel.org/kernel/tegra:
  [ARM] tegra: add MAINTAINERS entry
  [ARM] tegra: harmony: Add harmony board file
  [ARM] tegra: add pinmux support
  [ARM] tegra: add GPIO support
  [ARM] tegra: Add timer support
  [ARM] tegra: SMP support
  [ARM] tegra: Add clock support
  [ARM] tegra: Add IRQ support
  [ARM] tegra: initial tegra support

* 'for-linus' of git://github.com/schandinat/linux-2.6:
  drivers/video/via/via-gpio.c: fix warning
  viafb: Depends on X86
  fbdev: section cleanup in viafb driver
  viafb: fix accel_flags check_var bug
  viafb: probe cleanups
  viafb: remove ioctls which break the framebuffer interface
  viafb: update fix before calculating depth
  viafb: PLL value cleanup
  viafb: simplify lcd size "detection"
  viafb: fix PCI table
  viafb: add lcd scaling support for some IGPs
  viafb: improve lcd code readability
  viafb: remove duplicated scaling code
  MAINTAINERS: update viafb entry