Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Dillow took my suggestions and improved on them.
Here is this latest version.

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Remove #define ERR_PFX
Remove now unused member name from struct typhoon
Use pr_<level>
Use netdev_<level>
Coalesce long formats
Remove version information
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conversion in bf0dcbd9 missed the
new allocation in b44_rx.
This patch was used in OpenWRT for a long time.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do a PHY reset to test if there is an active phy and set the PHY address
to B44_PHY_ADDR_NO_PHY in case of an not active phy. This is needed for
the Linksys WRTSL54GS and Asus WL-500W.
This patch was used in OpenWRT for a long time.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PowerPC architecture does not require loads to independent bytes to be
ordered without adding an explicit barrier.

In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.

The problem occurs with packet split enabled where the TCP/IP header and data
are in different descriptors. If the reads go out of order we may have data
that doesn't match the TCP/IP header. Since we use hardware checksumming this
bad data is never verified and it makes it all the way to the application.

This bug was found during stress testing and adding this barrier has been shown
to fix it.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix commit 4cd24eaf (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For certain skews of the BE adapter, H/W Tx and Rx
counters could be common for more than one interface.
Add Tx and Rx counters in the adapter structure
(to maintain stats on a per interfae basis).
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently use of 64-bit DMA is disabled in r8169 unless the user passes the
use_dac module option. This is reasonable for conventional PCI devices where
broken chipsets may not handle dual-address-cycle transfers properly for
32-bit slots and so this may not be safe. However, PCI Express should not have
this problem and not using 64-bit DMA results in DMA transfers needlessly using
the IOMMU or SWIOTLB. Set the use_dac module parameter to a new default value of
-1 which results in 64-bit DMA being enabled by default for PCI Express devices
only.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are only two users of the dma_sync_single_range_for_cpu/device
API in mainline (mlx4 and ssb). The
dma_sync_single_range_for_cpu/device API has never been documented and
the dma_sync_single_for_cpu/device API also support a partial sync.

This converts mlx4 to use the dma_sync_single_for_cpu/device API
(preparations for the removal of the dma_sync_single_range_for_cpu/device API).
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Fri, Feb 19, 2010 at 13:51 +0100, Jiri Pirko wrote:
>
> <snip>
> >>@@ -1031,7 +1029,7 @@ static void greth_set_multicast_list(struct net_device *dev)
> >> 			return;
> >> 		}
> >>
> >>-		if (dev->mc_count == 0) {
> >>+		if (!netdev_mc_count(dev)) {
> also please use netdev_mc_empty() here.
Some driver cleanups:
* convert to use phy_find_first/phy_direct_connect
* convert to use netdev_mc_* helpers
* fixed missing validate_addr hook
* removed netdev_priv castings
Signed-off-by: NDenis Kirjanov <kirjanov@gmail.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removed fill_multicast_tbl function in smc91c92_cs and do the work inline

rewritten set_addresses function in xirc2ps_cs. This was kinda headache.
Simulated the original and new functions and they bahave the same.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To see the effect make sure you have an empty SPD.
On window1 "ip xfrm mon" and on window2 issue "ip xfrm policy flush"
You get prompt back in window2 and you see the flush event on window1.
With this fix, you still get prompt on window1 but no event on window2.

Thanks to Alexey Dobriyan for finding a bug in earlier version
when using pfkey to do the flushing.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To see the effect make sure you have an empty SAD.
On window1 "ip xfrm mon" and on window2 issue "ip xfrm state flush"
You get prompt back in window2 and you see the flush event on window1.
With this fix, you still get prompt on window1 but no event on window2.

Thanks to Alexey Dobriyan for finding a bug in earlier version
when using pfkey to do the flushing.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 2367 says flushing behavior should be:
1) user space -> kernel: flush
2) kernel: flush
3) kernel -> user space: flush event to ALL listeners

This is not realistic today in the presence of selinux policies
which may reject the flush etc. So we make the sequence become:
1) user space -> kernel: flush
2) kernel: flush
3) kernel -> user space: flush response to originater from #1
4) if there were no errors then:
kernel -> user space: flush event to ALL listeners
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 3bc38712 (handle NF_STOP and unknown verdicts in
nf_reinject) was a partial fix to packet leaks.

If user asks NF_STOLEN status, we must free the skb as well.
Reported-by: NAfi Gjermund <afigjermund@gmail.com>
Signed-off-by: NEric DUmazet <eric.dumazet@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

This patch fixes a bug that triggers an assertion if you create
a conntrack entry with a helper and netfilter debugging is enabled.
Basically, we hit the assertion because the confirmation flag is
set before the conntrack extensions are added. To fix this, we
move the extension addition before the aforementioned flag is
set.

This patch also removes the possibility of setting a helper for
existing conntracks. This operation would also trigger the
assertion since we are not allowed to add new extensions for
existing conntracks. We know noone that could benefit from
this operation sanely.

Thanks to Eric Dumazet for initial posting a preliminary patch
to address this issue.
Reported-by: NDavid Ramblewski <David.Ramblewski@atosorigin.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Reported by Stephen Rothwell.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2249065f ("netfilter: get rid of the grossness in netfilter.h")
inverted the logic for conditional hook invocation, breaking the
POST_ROUTING hook invoked by ip_output().

Correct the logic and remove an unnecessary initialization.
Reported-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level> and netif_msg_<test>
Remove local #define net_<test> macros
Remove periods from formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Remove periods from most formats
Coalesce long formats
Use printk_once
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to lack of time, space, motivation, hardware and probably expertise,
I have reluctantly decided to orphan the DECnet code in the kernel.

Judging by the deafening silence on the linux-decnet mailing list I
suspect it's either not being used anyway, or the few people that are
using it are happy with their older kernels.
Signed-Off-By: NChristine Caulfield <christine.caulfield@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net: free tx buffers when completions never arrive

In cases like when a pci device is disconnected on an error,
pending tx completions will never arrive. Unmap and free such
buffers in the tx cleanup path.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XFRMINHDRERROR counter is ambigous when validating forwarding
path. It makes it tricky to debug when you have both in and fwd
validation.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables fast retransmissions after one dupACK for
TCP if the stream is identified as thin. This will reduce
latencies for thin streams that are not able to trigger fast
retransmissions due to high packet interarrival time. This
mechanism is only active if enabled by iocontrol or syscontrol
and the stream is identified as thin.
Signed-off-by: NAndreas Petlund <apetlund@simula.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will make TCP use only linear timeouts if the
stream is thin. This will help to avoid the very high latencies
that thin stream suffer because of exponential backoff. This
mechanism is only active if enabled by iocontrol or syscontrol
and the stream is identified as thin. A maximum of 6 linear
timeouts is tried before exponential backoff is resumed.
Signed-off-by: NAndreas Petlund <apetlund@simula.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inline function to dynamically detect thin streams based on
the number of packets in flight. Used to dynamically trigger
thin-stream mechanisms if enabled by ioctl or sysctl.
Signed-off-by: NAndreas Petlund <apetlund@simula.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removed needless checks in arlan-main.c and slicoss.c
fixed bug in et131x_netdev.c to actually fill addresses in.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also removed needless checks in smsc95xx
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also bug in de2104x.c was corrected:
for (i = 0; i < 32; i++) loop should be outside mc_list iteration.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

also removed unnecessary checks
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>