DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.

Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Propagate errors returned by drivers from the s_filter callback back to
userland when updating scancode filters. This allows userland to see
when the filter couldn't be updated, usually because it's not a valid
filter for the hardware.

Previously the filter was being updated conditionally on success of
s_filter, but the write always reported success back to userland.
Reported-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a device id to support for PX-S1UD (PLEX ISDB-T usb dongle) which
has sms2270.
Signed-off-by: NSatoshi Nagahama <sattnag@aim.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since the introduction of the new OMAP DSS DVI connector driver in
commit 348077b1 ("OMAPDSS: Add new DVI
Connector driver"), DVI outputs report a new display type of
OMAP_DISPLAY_TYPE_DVI instead of OMAP_DISPLAY_TYPE_DPI. Handle the new
type in the IRQ handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

New board addition. No other changes.

[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: NPojar George <geoubuntu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

These chips makes use of the media_entity in the v4l2_subdev struct
and is therefor dependent of the  MEDIA_CONTROLLER config.
Signed-off-by: NMarcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix this linker warning:
WARNING: "__divdi3" [media_build/v4l/drx39xyj.ko] undefined!

[m.chehab@samsung.com: add include for asm/div64.h]
Signed-off-by: NGianluca Gennari <gennarone@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

try_fmt should just set field to NONE and not return an error if
a different field was passed.

buf_prepare should check if the field passed in from userspace has a
supported field value. At the moment only NONE is supported and ANY
is mapped to NONE.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

- Set the sequence counters correctly.
- Copy timestamps, timecode, relevant buffer flags and field from
  the received buffer to the outgoing buffer.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

To keep the vb2 buffer administration in balance stop_streaming() must
return any pending buffers to the vb2 framework.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is no reason why we shouldn't enable this here.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

v4l2_compliance fix.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This resolves an issue raised by v4l2-compliance: if the given format does
not exist, then pick a default format.

While there is an exception regarding this for TV capture drivers, this
m2m driver should do the right thing.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The default of 1 second is a bit painful, switch to a 25 Hz framerate.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch removes meaningless assignment of memory bank to itself.
Signed-off-by: NSeung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is no any reason to use comma here.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for async device registration to the adv7180 driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The device driver core already prints out a very similar message when a driver
fails to probe. No need to print one in the driver itself.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The device can't possibly be registered at this point, so no need to to call
v4l2_device_unregister_subdev().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Make sure to free the control handler when the device is removed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The mutex is used in the subdev callbacks, so unregister the subdev before the
mutex is destroyed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Document that it is now possible to call G/S_EDID from video nodes, not
just sub-device nodes. Add a note that -EINVAL will be returned if
the pad does not support EDIDs.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Support this ioctl as part of the v4l2 core. Use the new ioctl
name and struct v4l2_edid type in the existing core code.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Struct v4l2_subdev_edid and the VIDIOC_SUBDEV_G/S_EDID ioctls were
specific for subdevices, but for hardware with a simple video pipeline
you do not need/want to create subdevice nodes to just get/set the EDID.

Move the v4l2_subdev_edid struct to v4l2-common.h and rename as
v4l2_edid. Add the same ioctls to videodev2.h as well, thus allowing
this API to be used with both video nodes and v4l-subdev nodes.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The wrong ioctl numbers were used due to a copy-and-paste error.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org      # for v3.7 and up
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdfSigned-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Three Flash fault are added. V4L2_FLASH_FAULT_UNDER_VOLTAGE for the case low
voltage below the min. limit. V4L2_FLASH_FAULT_INPUT_VOLTAGE for the case
falling input voltage and chip adjust flash current not occur under voltage
event. V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE for the case the temperature
exceed the maximun limit
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Descriptions for flash faults V4L2_FLASH_FAULT_UNDER_VOLTAGE,
V4L2_FLASH_FAULT_INPUT_VOLTAGE, and V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE.

Removed spaces before tabs.
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If we have no pdata defined and driver fails to register we leak memory.
Converting to devm_kzalloc prevents this to happen.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Let's keep the style for all comments in the code, namely using small letters
whenever it's possible.

There is no functional change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is no need to keep the FSF address inside each file. Moreover, it might
change in future which will make this one obsolete.

There is no functional change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Empty port nodes are allowed but currently unsupported as the
v4l2_of_get_next_endpoint() function assumes that all port nodes have at
least an endpoint. Fix this.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since I'm currently unable to dedicate sufficient time to the maintainership
of these two drivers update their status to "orphan" until new maintainers
appear.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for MBUS YUV10 BT656 and BT601 formats at rcar driver.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes memory leak introduced by
commit 47d8c881.
Signed-off-by: NDean Anderson <linux-dev@sensoray.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Set permissions on the debug module parameter to make it appear in sysfs.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch fixes the following warning:

drivers/media/i2c/tvp5150.c: In function '__tvp5150_try_crop':
include/linux/kernel.h:762:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__min);  \
                 ^
drivers/media/i2c/tvp5150.c:886:16: note: in expansion of macro 'clamp'
  rect->width = clamp(rect->width,
                ^
include/linux/kernel.h:763:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__max);  \
                 ^
drivers/media/i2c/tvp5150.c:886:16: note: in expansion of macro 'clamp'
  rect->width = clamp(rect->width,
                ^
include/linux/kernel.h:762:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__min);  \
                 ^
drivers/media/i2c/tvp5150.c:904:17: note: in expansion of macro 'clamp'
  rect->height = clamp(rect->height,
                 ^
include/linux/kernel.h:763:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
  (void) (&__val == &__max);  \
                 ^
drivers/media/i2c/tvp5150.c:904:17: note: in expansion of macro 'clamp'
  rect->height = clamp(rect->height,
                 ^
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>