Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 17 7月, 2021 3 次提交
  3. 07 7月, 2021 1 次提交
    • T
      ixgbevf: use xso.real_dev instead of xso.dev in callback functions of struct xfrmdev_ops · 2de7e4f6
      由 Taehee Yoo 提交于 
      There are two pointers in struct xfrm_state_offload, *dev, *real_dev.
These are used in callback functions of struct xfrmdev_ops.
The *dev points whether bonding interface or real interface.
If bonding ipsec offload is used, it points bonding interface If not,
it points real interface.
And real_dev always points real interface.
So, ixgbevf should always use real_dev instead of dev.
Of course, real_dev always not be null.

Test commands:
    ip link add bond0 type bond
    #eth0 is ixgbevf interface
    ip link set eth0 master bond0
    ip link set bond0 up
    ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in

Splat looks like:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 6 PID: 688 Comm: ip Not tainted 5.13.0-rc3+ #1168
RIP: 0010:ixgbevf_ipsec_find_empty_idx+0x28/0x1b0 [ixgbevf]
Code: 00 00 0f 1f 44 00 00 55 53 48 89 fb 48 83 ec 08 40 84 f6 0f 84 9c
00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02
84 c0 74 08 3c 01 0f 8e 4c 01 00 00 66 81 3b 00 04 0f
RSP: 0018:ffff8880089af390 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: ffff8880089af4f8 R08: 0000000000000003 R09: fffffbfff4287e11
R10: 0000000000000001 R11: ffff888005de8908 R12: 0000000000000000
R13: ffff88810936a000 R14: ffff88810936a000 R15: ffff888004d78040
FS:  00007fdf9883a680(0000) GS:ffff88811a400000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055bc14adbf40 CR3: 000000000b87c005 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 ixgbevf_ipsec_add_sa+0x1bf/0x9c0 [ixgbevf]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? ixgbevf_ipsec_parse_proto_keys.isra.9+0x280/0x280 [ixgbevf]
 ? lock_acquire+0x191/0x720
 ? bond_ipsec_add_sa+0x48/0x350 [bonding]
 ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0
 ? rcu_read_lock_held+0x91/0xa0
 ? rcu_read_lock_sched_held+0xc0/0xc0
 bond_ipsec_add_sa+0x193/0x350 [bonding]
 xfrm_dev_state_add+0x2a9/0x770
 ? memcpy+0x38/0x60
 xfrm_add_sa+0x2278/0x3b10 [xfrm_user]
 ? xfrm_get_policy+0xaa0/0xaa0 [xfrm_user]
 ? register_lock_class+0x1750/0x1750
 xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? find_held_lock+0x3a/0x1c0
 ? mutex_lock_io_nested+0x1210/0x1210
 ? sched_clock_cpu+0x18/0x170
 netlink_rcv_skb+0x121/0x350
[ ... ]

Fixes: 272c2330 ("xfrm: bail early on slave pass over skb")
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2de7e4f6
  5. 02 7月, 2021 11 次提交
  7. 26 6月, 2021 4 次提交
  9. 25 6月, 2021 7 次提交
  11. 19 6月, 2021 2 次提交
  13. 18 6月, 2021 9 次提交
  15. 11 6月, 2021 3 次提交
    • J
      ice: enable transmit timestamps for E810 devices · ea9b847c
      由 Jacob Keller 提交于 
      Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.

The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.

Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.

To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.

In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.

For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.

Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.

This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.

It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.

Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.

Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.

With this change, E810 devices should be able to perform basic PTP
functionality.

Future changes will extend the support to cover the E822-based devices.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
      ea9b847c
    • J
      ice: enable receive hardware timestamping · 77a78115
      由 Jacob Keller 提交于 
      Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.

Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.

The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.

If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is

  PHC - (lower_32_bits(PHC) - timestamp)

If the Rx timestamp was captured after the PHC time, then the real
timestamp is

  PHC + (timestamp - lower_32_bits(PHC))

These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.

In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.

Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.

Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.

To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.

Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.

With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
      77a78115
    • J
      ice: report the PTP clock index in ethtool .get_ts_info · 67569a7f
      由 Jacob Keller 提交于 
      Now that the driver registers a PTP clock device that represents the
clock hardware, it is important that the clock index is reported via the
ethtool .get_ts_info callback.

The underlying hardware resource is shared between multiple PF
functions. Only one function owns the hardware resources associated with
a timer, but multiple functions may be associated with it for the
purposes of timestamping.

To support this, the owning PF will store the clock index into the
driver shared parameters buffer in firmware. Other PFs will look up the
clock index by reading the driver shared parameter on demand when
requested via the .get_ts_info ethtool function.

In this way, all functions which are tied to the same timer are able to
report the clock index. Userspace software such as ptp4l performs
a look up on the netdev to determine the associated clock, and all
commands to control or configure the clock will be handled through the
controlling PF.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
      67569a7f