Due to recent changes to the way that the MITM requirement is set for
outgoing pairing attempts we can no longer rely on the hcon->auth_type
variable (which is actually good since it was formed from BR/EDR
concepts that don't really exist for SMP).

To match the logic that BR/EDR now uses simply rely on the local IO
capability and/or needed security level to set the MITM requirement for
outgoing pairing requests.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Default values for various channel settings were missing. This
way channel users do not need to set default values themselves.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The universal/local bit handling was incorrectly done in the code.

So when setting EUI address from BD address we do this:
- If BD address type is PUBLIC, then we clear the universal bit
  in EUI address. If the address type is RANDOM, then the universal
  bit is set (BT 6lowpan draft chapter 3.2.2)
- After this we invert the universal/local bit according to RFC 2464

When figuring out BD address we do the reverse:
- Take EUI address from stateless IPv6 address, invert the
  universal/local bit according to RFC 2464
- If universal bit is 1 in this modified EUI address, then address
  type is set to RANDOM, otherwise it is PUBLIC

Note that 6lowpan_iphc.[ch] does the final toggling of U/L bit
before sending or receiving the network packet.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

When checking whether we need to request authentication or not we should
include HCI_SECURITY_FIPS to the levels that always need authentication.
This patch fixes check for it in the hci_outgoing_auth_needed()
function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

In case there are new LTK types in the future we shouldn't just blindly
assume that != MGMT_LTK_UNAUTHENTICATED means that the key is
authenticated. This patch adds explicit checks for each allowed key type
in the form of a switch statement and skips any key which has an unknown
value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: NAdam Lee <adam8157@gmail.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

On the mgmt level we have a key type parameter which currently accepts
two possible values: 0x00 for unauthenticated and 0x01 for
authenticated. However, in the internal struct smp_ltk representation we
have an explicit "authenticated" boolean value.

To make this distinction clear, add defines for the possible mgmt values
and do conversion to and from the internal authenticated value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Now that smp_confirm() is called "inline" we can have it return a
response code and have the sending of it be done in the shared place for
command handlers. One exception is when we're entering smp.c from mgmt.c
when user space responds to authentication, in which case we still need
our own code to call smp_failure().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since we're now calling smp_random() "inline" we can have it directly
return a response code and have the shared command handler send the
response.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There's no reason to have "smp" in this variable name since it is
already part of the SMP struct which provides sufficient context.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the SMP code was initially created (mid-2011) parts of the
Bluetooth subsystem were still not converted to use workqueues. This
meant that the crypto calls, which could sleep, couldn't be called
directly. Because of this the "confirm" and "random" work structs were
introduced.

These days the entire Bluetooth subsystem runs through workqueues which
makes these structs unnecessary. This patch removes them and converts
the calls to queue them to use direct function calls instead.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There is no reason to have the initial local value conditional to
whether the remote value has bonding set or not. We can either way start
off with the value we received.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There are no users of the smp_chan struct outside of smp.c so move it
away from smp.h. The addition of the l2cap.h include to hci_core.c,
hci_conn.c and mgmt.c is something that should have been there already
previously to avoid warnings of undeclared struct l2cap_conn, but the
compiler warning was apparently shadowed away by the mention of
l2cap_conn in the struct smp_chan definition.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

conn_info_age value is calculated in ms, so need to be converted to
jiffies.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for max_tx_power in Get Connection Information
request. Value is read only once for given connection and then always
returned in response as parameter.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support to store local maximum TX power level for
connection when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

TX power for LE links is immutable thus we do not need to query for it
if already have value.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for Get Connection Information mgmt command
which can be used to query for information about connection, i.e. RSSI
and local TX power level.

In general values cached in hci_conn are returned as long as they are
considered valid, i.e. do not exceed age limit set in hdev. This limit
is calculated as random value between min/max values to avoid client
trying to guess when to poll for updated information.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds conn_info_min_age and conn_info_max_age parameters to
debugfs which determine lifetime of connection information. Actual
lifetime will be random value between min and max age.

Default values for min and max age are 1000ms and 3000ms respectively.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support to store local TX power level for connection
when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch increments the management interface revision due to the
changes with the Device Found management event and other fixes.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

After hardware reset, some BCM Bluetooth adapters obtain their initial firmware
from OTPROM chip. Once this initial firmware is running, the firmware can be
further upgraded over HCI interface with .hcd files provided by Broadcom. This
is also known as "patch RAM" support. This change implements that.

If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues
to operate with the initial firmware. Sample kernel log:
  hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
  Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found

If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and
it starts using the new firmware. Sample kernel log:
  hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
  Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e
  Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e

Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support to store RSSI for connection when reply for
HCI_Read_RSSI is received.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Invalid Parameters error code is used to indicate that the command
length is invalid or that a parameter is outside of the specified range.
This error code wasn't clearly specified in the Bluetooth 4.0
specification but since 4.1 this has been fixed.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Enabling CONFIG_DEBUG_ATOMIC_SLEEP has shown that some rfcomm functions
acquiring spinlocks call sleeping locks further in the chain.  Converting
the offending spinlocks into mutexes makes sleeping safe.
Signed-off-by: NLibor Pechacek <lpechacek@suse.cz>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

H4 states are not used anymore.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Change subcmd parameter from int to u8 to match its use:
btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1);
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The HCISETRAW ioctl command is not really useful. To utilize raw and
direct access to the HCI controller, the HCI User Channel feature has
been introduced. Return EOPNOTSUPP to indicate missing support for
this command.

For legacy reasons hcidump used to use HCISETRAW for permission check
to return proper error codes to users. To keep backwards compability
return EPERM in case the caller does not have CAP_NET_ADMIN capability.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The GAP Specification gives the flexibility to decide whether MITM
Protection is requested or not (Bluetooth Core Specification v4.0
Volume 3, part C, section 6.5.3) when replying to an
HCI_EV_IO_CAPA_REQUEST event.

The recommendation is *not* to set this flag "unless the security
policy of an available local service requires MITM Protection"
(regardless of the bonding type). However, the kernel doesn't
necessarily have this information and therefore the safest choice is
to always use MITM Protection, also for General Bonding.

This patch changes the behavior for the General Bonding initiator
role, always requesting MITM Protection even if no high security level
is used. Depending on the remote capabilities, the protection might
not be actually used, and we will accept this locally unless of course
a high security level was originally required.

Note that this was already done for Dedicated Bonding. No-Bonding is
left unmodified because MITM Protection is normally not desired in
these cases.
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NTimo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When responding to a remotely-initiated pairing procedure, a MITM
protected SSP associaton model can be used for pairing if both local
and remote IO capabilities are set to something other than
NoInputNoOutput, regardless of the bonding type (Dedicated or
General).

This was already done for Dedicated Bonding but this patch proposes to
use the same policy for General Bonding as well.

The GAP Specification gives the flexibility to decide whether MITM
Protection is used ot not (Bluetooth Core Specification v4.0 Volume 3,
part C, section 6.5.3).

Note however that the recommendation is *not* to set this flag "unless
the security policy of an available local service requires MITM
Protection" (for both Dedicated and General Bonding). However, as we are
already requiring MITM for Dedicated Bonding, we will follow this
behaviour also for General Bonding.
Signed-off-by: NTimo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Do not always set the MITM protection requirement by default in the
field conn->auth_type, since this will be added later in
hci_io_capa_request_evt(), as part of the requirements specified in
HCI_OP_IO_CAPABILITY_REPLY.

This avoids a hackish exception for the auto-reject case, but doesn't
change the behavior of the code at all.
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Refactor the code without changing its behavior by handling the
no-bonding cases first followed by General Bonding.
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NTimo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When sending out a device found event caused by an advertising report in
the situation where we couldn't store the report as a pending one, the
code was incorrectly trying to use the address and address type from the
pending data. Since the pending data is cleared in the previous line
this causes a potentially incorrect address type and an address of
BDADDR_ANY. This patch fixes the call to use the address information
correctly from the received advertising report.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To be consistent, lets use msec for this timeout as well.

Note: This define value is a minimum scan time taken from BT Core spec 4.0,
Vol 3, Part C, chapter 9.2.6
Signed-off-by: NLukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With this patch it is possible to control discovery interleaved
timeout value from debugfs.

It is for fine tuning of this timeout.
Signed-off-by: NLukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Keep msec instead of jiffies in this define. This is needed by following
patch where we want this timeout to be exposed in debugfs.

Note: Value of this timeout comes from recommendation in BT Core Spec.4.0,
Vol 3, Part C, chapter 13.2.1.
Signed-off-by: NLukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch improves readability and makes future changes easier.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ssp parameter is supposed to be a mandatory one and there are no
callers that would pass NULL to this function. Removing this unnecessary
NULL check also makes (false positive) static analyzer warnings go away.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When sending a pending device found event triggered by disabling LE
scanning we should use the stored RSSI instead of sending a zero value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>