The T10 SBC UNMAP command does not provide any hard guarantees that
blocks will return zeroes on a subsequent READ. This is due to the fact
that the device server is free to silently ignore all or parts of the
request.

The only way to ensure that a block consistently returns zeroes after
being unmapped is to use WRITE SAME with the UNMAP bit set. Should the
device be unable to unmap one or more blocks described by the command it
is required to manually write zeroes to them.

Until now we have preferred UNMAP over the WRITE SAME variants to
accommodate thinly provisioned devices that predated the final SBC-3
spec. This patch changes the heuristic so that we favor WRITE SAME(16)
or (10) over UNMAP if these commands are marked as supported in the
Logical Block Provisioning VPD page.

The patch also disables discard_zeroes_data for devices operating in
UNMAP mode.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

No need to verify the passthrough ioctls, the real handler will
take care of that.  Also make sure not to block for resets on
O_NONBLOCK fds.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

The calling conventions for this function are bad as it could return
-ENODEV both for a device not currently online and a not recognized ioctl.

Add a new scsi_ioctl_block_when_processing_errors function that wraps
scsi_block_when_processing_errors with the a special case for the
SG_SCSI_RESET ioctl command, and handle the SG_SCSI_RESET case itself
in scsi_ioctl.  All callers of scsi_ioctl now must call the above helper
to check for the EH state, so that the ioctl handler itself doesn't
have to.
Reported-by: NRobert Elliott <Elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Pull the common code from the two callers into the function,
and rename it to scsi_ioctl_reset.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Modify scsi_find_tag() and scsi_host_find_tag() such that these
functions can translate a tag generated by blk_mq_unique_tag().
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Allow a SCSI LLD to declare how many hardware queues it supports
by setting Scsi_Host.nr_hw_queues before calling scsi_add_host().
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The queuecommand() callback functions in SCSI low-level drivers
need to know which hardware context has been selected by the
block layer. Since this information is not available in the
request structure, and since passing the hctx pointer directly to
the queuecommand callback function would require modification of
all SCSI LLDs, add a function to the block layer that allows to
query the hardware context index.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Acked-by: NJens Axboe <axboe@kernel.dk>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There can be quite a lot of I/O error messages, even on smaller
machines. So we need to ratelimit them to not overwhelm logging.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Tested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The .eh_abort_handler needs to return SUCCESS, FAILED, or
FAST_IO_FAIL. So fixup all callers to adhere to this requirement.
Reviewed-by: NRobert Elliott <elliott@hp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

scsi_try_to_abort_cmd() should only return SUCCESS, FAILED, or
FAST_IO_FAIL. So document that in the function description and simplify
the logging message.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Suggested-by: NChristoph Hellwig <hch@infradead.org>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The EH statistics are per host, so we should be using
shost_printk() here.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Suggested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use the matching scope for logging messages to allow for
better command tracing.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Suggested-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Simplify scsi_log_(send|completion) by externalizing
scsi_mlreturn_string() and always print the command address.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Open-code scsi_print_result in sd.c, and cleanup logging to
not print duplicate informations.
Also remove the call to scsi_show_result() in ufshcd.c
to be consistent with other callers of scsi_execute().

With that we can remove scsi_show_result in constants.c
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Export functions for later use.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Calling scsi_print_command should not be necessary during abort;
if the information is required one should enable scsi logging.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

print_opcode_name() was only ever called with a '0' argument
from LLDDs and ULDs which were _not_ supporting variable length
CDBs, so the 'if' clause was never triggered.
Instead we should be using the last argument to specify
the cdb length to avoid accidental overflow when reading
the cdb buffer.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Consolidate the CDB opcode lookup in scsi_opcode_sa_name(),
so that we don't have to call several functions to figure
out the CDB opcode string.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Instead of having two versions of print_opcode_name() we
should be consolidating them into one version.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Implement a lookup array for SERVICE ACTION commands instead
of hardcoding it in a large switch statement.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Last caller is gone, so we can remove it.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert scsi_normalize_sense() and friends to return 'bool'
instead of an integer.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NYoshihiro Yunomae <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Currently we're only decoding sense extras for tape devices.
And even there only for fixed format sense formats.
As this is of rather limited use in the general case we should
be stop trying to decode sense extras; the tape driver does
its own decoding anyway.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If scsi_normalize_sense() fails we couldn't decode the sense
buffer, and the scsi_sense_hdr fields are invalid.
For those cases we should rather dump the sense buffer
and not try to decode invalid fields.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The 53c700 driver would be using scsi_print_sense() in a debug
statement, which was never compiled in. Plus the same information
can get retrieved with logging. So remove it.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update logging messages to use dev_printk() variants for correct
device annotations.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

fas216 returns DID_BAD_TARGET for an incomplete data
transfer. The midlayer uses DID_BAD_TARGET to signal
a non-existing or not reachable target. So we should
rather be using DID_ERROR here.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update acornscsi to use scsi_print_command() instead of the
underscore version and use scmd_printk() in acornscsi_done().
This will add correct device annotations in the resulting message.
And we should be using set_host_byte() for setting the
final result.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

We should be using the standard dev_printk() variants for
sense code printing.

[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Like scmd_printk(), but the device name is passed in as
a string. Can be used by eg ULDs which do not have access
to the scsi_cmnd structure.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Remove all uncommented debugging code and move all
printk() statements over to dev_printk().
And while we're at it we should be doing a whitespace
cleanup, too.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

sd_done() was calling scsi_print_sense() for a sense code
of 'NO_SENSE'.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Unused.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Some SES devices give non-unique Element Descriptors as part of the
Element Descriptor diag page. Since we use these for creating sysfs
entries, they need to be unique. The specification doesn't require
these to be unique.

Eg:
$ sg_ses -p 7 /dev/sg0
  FTS CORP  TXS6_SAS20BPX12   0500
    enclosure services device
Element descriptor In diagnostic page:
  generation code: 0x0
  element descriptor by type list
    Element type: Array device, subenclosure id: 0
      Overall descriptor: ArrayDevicesInSubEnclsr0
      Element 1 descriptor: ArrayDevice00
      Element 2 descriptor: ArrayDevice01
      Element 3 descriptor: ArrayDevice02
      Element 4 descriptor: ArrayDevice03
      Element 5 descriptor: ArrayDevice03
      Element 6 descriptor: ArrayDevice03
      Element 7 descriptor: ArrayDevice03
      Element 8 descriptor: ArrayDevice03
      Element 9 descriptor: ArrayDevice03
      Element 10 descriptor: ArrayDevice03
      Element 11 descriptor: ArrayDevice03
      Element 12 descriptor: ArrayDevice03

Based on http://thread.gmane.org/gmane.linux.scsi/69289. This
version implements James' ideas about the naming convention
Signed-off-by: NMarkus Stockhausen <stockhausen@collogia.de>
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch adds a debug_flag parameter that can be set on module load, and allows the DEBUG facility without a module recompile.
Note that now DEBUG 1 is the default with this patch.

Usage: modprobe st debug_flag=1
Signed-off-by: NLaurence Oberman <loberman@redhat.com>
Acked-by: NKai M??kisara <kai.makisara@kolumbus.fi>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Further to a January 2013 thread titled: "[PATCH] SG_SCSI_RESET ioctl
should only perform requested operation" by Jeremy Linton a patch (v3)
is presented that expands the existing ioctl to include "no_escalate"
versions to the existing resets. This requires no changes to SCSI low
level drivers (LLDs); it adds several more finely tuned reset options
to the user space. For example:

   /* This call remains the same, with the same escalating semantics
    * if the device (LU) reset fail. That is: on failure to try a
    * target reset and if that fails, try a bus reset, and if that fails
    * try a host (i.e. LLD) reset. */
   val = SG_SCSI_RESET_DEVICE;
   res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);

   /* What follows is a new option introduced by this patch series. Only
    * a device reset is attempted. If that fails then an appropriate
    * error code is provided. N.B. There is no reset escalation. */
   val = SG_SCSI_RESET_DEVICE | SG_SCSI_RESET_NO_ESCALATE;
   res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);
Signed-off-by: NDouglas Gilbert <dgilbert@interlog.com>
Reviewed-by: NJeremy Linton <jlinton@tributary.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

As sparse correctly pointed out, scsi_partsize should use get_unaligned_le32
to read PC partition tables from disk, as they are little endian.

The result of this bug is that we returned incorrect geometries on big
endian systems when using the scsicam variant.  Which probably doesn't
matter as only old x86 systems every cared about the geometry.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>