When using controller based address resolution, then the destination
address type during le_conn_complete uses 0x02 & 0x03 if controller
resolves the destination address(RPA).
These address types need to be converted back into either 0x00 0r 0x01
Signed-off-by: NSathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Because mSBC frames do not need to be aligned to the SCO packet
boundary. Using USB ALT 3 let HCI payload >= 60 bytes, let mSBC
data satisfy 60 Bytes avoid payload unaligned situation and fixed
some headset no voise issue.

USB Alt 3 supported also need HFP support transparent MTU in 72 Bytes.
Signed-off-by: NHilda Wu <hildawu@realtek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The use of l2cap_chan_del is not safe under a loop using
list_for_each_entry.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The use of l2cap_chan_del is not safe under a loop using
list_for_each_entry.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Even with rate limited reporting this is very spammy and since
it is remote device that is providing bogus data there is no
need to report this as error.

Since real_len variable was used only to allow conditional error
message it is now also removed.

[72454.143336] bt_err_ratelimited: 10 callbacks suppressed
[72454.143337] Bluetooth: hci0: advertising data len corrected
[72454.296314] Bluetooth: hci0: advertising data len corrected
[72454.892329] Bluetooth: hci0: advertising data len corrected
[72455.051319] Bluetooth: hci0: advertising data len corrected
[72455.357326] Bluetooth: hci0: advertising data len corrected
[72455.663295] Bluetooth: hci0: advertising data len corrected
[72455.787278] Bluetooth: hci0: advertising data len corrected
[72455.942278] Bluetooth: hci0: advertising data len corrected
[72456.094276] Bluetooth: hci0: advertising data len corrected
[72456.249137] Bluetooth: hci0: advertising data len corrected
[72459.416333] bt_err_ratelimited: 13 callbacks suppressed
[72459.416334] Bluetooth: hci0: advertising data len corrected
[72459.721334] Bluetooth: hci0: advertising data len corrected
[72460.011317] Bluetooth: hci0: advertising data len corrected
[72460.327171] Bluetooth: hci0: advertising data len corrected
[72460.638294] Bluetooth: hci0: advertising data len corrected
[72460.946350] Bluetooth: hci0: advertising data len corrected
[72461.225320] Bluetooth: hci0: advertising data len corrected
[72461.690322] Bluetooth: hci0: advertising data len corrected
[72462.118318] Bluetooth: hci0: advertising data len corrected
[72462.427319] Bluetooth: hci0: advertising data len corrected
[72464.546319] bt_err_ratelimited: 7 callbacks suppressed
[72464.546319] Bluetooth: hci0: advertising data len corrected
[72464.857318] Bluetooth: hci0: advertising data len corrected
[72465.163332] Bluetooth: hci0: advertising data len corrected
[72465.278331] Bluetooth: hci0: advertising data len corrected
[72465.432323] Bluetooth: hci0: advertising data len corrected
[72465.891334] Bluetooth: hci0: advertising data len corrected
[72466.045334] Bluetooth: hci0: advertising data len corrected
[72466.197321] Bluetooth: hci0: advertising data len corrected
[72466.340318] Bluetooth: hci0: advertising data len corrected
[72466.498335] Bluetooth: hci0: advertising data len corrected
[72469.803299] bt_err_ratelimited: 10 callbacks suppressed
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=203753
Cc: stable@vger.kernel.org
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the 0cf3:e500 Bluetooth device (from a QCA9377 board) as a
QCA_ROME device.  It appears to be functionally identical to another device
ID, also from a QCA9377 board, which was previously marked as QCA_ROME in
0a03f98b
("Bluetooth: Add a new 04ca:3015 QCA_ROME device").

Without this patch, the WiFi side of the QCA9377 board is slow or unusable
when the Bluetooth side is in use.

See https://askubuntu.com/a/1137852 for another report of QCA_ROME fixing
this issue for this device ID.

/sys/kernel/debug/usb/devices:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e500 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NDaniel Lenski <dlenski@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750
controller.
Signed-off-by: NVenkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Converted Qualcomm Bluetooth binidings to DT schema.
Signed-off-by: NVenkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Moved extracting rom version info to common place as this code is
common in all if else ladder in qca_uart_setup.
Signed-off-by: NVenkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

1. Added support to download firmware image with mbn type for wcn6750
   as it supports mbn type image.
2. If mbn type image is not present then check for tlv type image.
3. Added debug logs for mbn type image.
Signed-off-by: NVenkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.

Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
   status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
   renamed it to qca_regulator_init().
Signed-off-by: NVenkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Rfkill block and unblock Intel USB Bluetooth [8087:0026] may make it
stops working:
[  509.691509] Bluetooth: hci0: HCI reset during shutdown failed
[  514.897584] Bluetooth: hci0: MSFT filter_enable is already on
[  530.044751] usb 3-10: reset full-speed USB device number 5 using xhci_hcd
[  545.660350] usb 3-10: device descriptor read/64, error -110
[  561.283530] usb 3-10: device descriptor read/64, error -110
[  561.519682] usb 3-10: reset full-speed USB device number 5 using xhci_hcd
[  566.686650] Bluetooth: hci0: unexpected event for opcode 0x0500
[  568.752452] Bluetooth: hci0: urb 0000000096cd309b failed to resubmit (113)
[  578.797955] Bluetooth: hci0: Failed to read MSFT supported features (-110)
[  586.286565] Bluetooth: hci0: urb 00000000c522f633 failed to resubmit (113)
[  596.215302] Bluetooth: hci0: Failed to read MSFT supported features (-110)

Or kernel panics because other workqueues already freed skb:
[ 2048.663763] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 2048.663775] #PF: supervisor read access in kernel mode
[ 2048.663779] #PF: error_code(0x0000) - not-present page
[ 2048.663782] PGD 0 P4D 0
[ 2048.663787] Oops: 0000 [#1] SMP NOPTI
[ 2048.663793] CPU: 3 PID: 4491 Comm: rfkill Tainted: G        W         5.13.0-rc1-next-20210510+ #20
[ 2048.663799] Hardware name: HP HP EliteBook 850 G8 Notebook PC/8846, BIOS T76 Ver. 01.01.04 12/02/2020
[ 2048.663801] RIP: 0010:__skb_ext_put+0x6/0x50
[ 2048.663814] Code: 8b 1b 48 85 db 75 db 5b 41 5c 5d c3 be 01 00 00 00 e8 de 13 c0 ff eb e7 be 02 00 00 00 e8 d2 13 c0 ff eb db 0f 1f 44 00 00 55 <8b> 07 48 89 e5 83 f8 01 74 14 b8 ff ff ff ff f0 0f c1
07 83 f8 01
[ 2048.663819] RSP: 0018:ffffc1d105b6fd80 EFLAGS: 00010286
[ 2048.663824] RAX: 0000000000000000 RBX: ffff9d9ac5649000 RCX: 0000000000000000
[ 2048.663827] RDX: ffffffffc0d1daf6 RSI: 0000000000000206 RDI: 0000000000000000
[ 2048.663830] RBP: ffffc1d105b6fd98 R08: 0000000000000001 R09: ffff9d9ace8ceac0
[ 2048.663834] R10: ffff9d9ace8ceac0 R11: 0000000000000001 R12: ffff9d9ac5649000
[ 2048.663838] R13: 0000000000000000 R14: 00007ffe0354d650 R15: 0000000000000000
[ 2048.663843] FS:  00007fe02ab19740(0000) GS:ffff9d9e5f8c0000(0000) knlGS:0000000000000000
[ 2048.663849] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2048.663853] CR2: 0000000000000000 CR3: 0000000111a52004 CR4: 0000000000770ee0
[ 2048.663856] PKRU: 55555554
[ 2048.663859] Call Trace:
[ 2048.663865]  ? skb_release_head_state+0x5e/0x80
[ 2048.663873]  kfree_skb+0x2f/0xb0
[ 2048.663881]  btusb_shutdown_intel_new+0x36/0x60 [btusb]
[ 2048.663905]  hci_dev_do_close+0x48c/0x5e0 [bluetooth]
[ 2048.663954]  ? __cond_resched+0x1a/0x50
[ 2048.663962]  hci_rfkill_set_block+0x56/0xa0 [bluetooth]
[ 2048.664007]  rfkill_set_block+0x98/0x170
[ 2048.664016]  rfkill_fop_write+0x136/0x1e0
[ 2048.664022]  vfs_write+0xc7/0x260
[ 2048.664030]  ksys_write+0xb1/0xe0
[ 2048.664035]  ? exit_to_user_mode_prepare+0x37/0x1c0
[ 2048.664042]  __x64_sys_write+0x1a/0x20
[ 2048.664048]  do_syscall_64+0x40/0xb0
[ 2048.664055]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 2048.664060] RIP: 0033:0x7fe02ac23c27
[ 2048.664066] Code: 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
[ 2048.664070] RSP: 002b:00007ffe0354d638 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 2048.664075] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007fe02ac23c27
[ 2048.664078] RDX: 0000000000000008 RSI: 00007ffe0354d650 RDI: 0000000000000003
[ 2048.664081] RBP: 0000000000000000 R08: 0000559b05998440 R09: 0000559b05998440
[ 2048.664084] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000003
[ 2048.664086] R13: 0000000000000000 R14: ffffffff00000000 R15: 00000000ffffffff

So move the shutdown callback to a place where workqueues are either
flushed or cancelled to resolve the issue.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the device ID for the BCM43430B0 module, found e.g. in
certain revisions of AMPAK AP6212 chip. The required firmware file is
named 'BCM43430B0.hcd'.
Signed-off-by: NMikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

struct firmware::data is marked const, and when the firmware is
compressed with xz (default at least with Fedora) it's mapped read-only
which results in a crash:

BUG: unable to handle page fault for address: ffffae57c0ca5047
PGD 100000067 P4D 100000067 PUD 1001ce067 PMD 10165a067 PTE 8000000112bba161
Oops: 0003 [#1] SMP NOPTI
CPU: 3 PID: 204 Comm: kworker/u17:0 Not tainted 5.12.1-test+ #1
Hardware name: Dell Inc. XPS 13 9310/0F7M4C, BIOS 1.2.5 12/10/2020
Workqueue: hci0 hci_power_on [bluetooth]
RIP: 0010:qca_download_firmware+0x27c/0x4e0 [btqca]
Code: 1b 75 04 80 48 0c 01 0f b7 c6 8d 54 02 0c 41 39 d7 0f 8e 62 fe ff ff 48 63 c2 4c 01 e8 0f b7 38 0f b7 70 02 66 83 ff 11 75 d3 <80> 48 0c 80 41 83 fc 03 7e 6e 88 58 0d eb ce 41 0f b6 45 0e 48 8b
RSP: 0018:ffffae57c08dfc68 EFLAGS: 00010246
RAX: ffffae57c0ca503b RBX: 000000000000000e RCX: 0000000000000000
RDX: 0000000000000037 RSI: 0000000000000006 RDI: 0000000000000011
RBP: ffff978d9949e000 R08: ffff978d84ed7540 R09: ffffae57c0ca5000
R10: 000000000010cd00 R11: 0000000000000001 R12: 0000000000000005
R13: ffffae57c0ca5004 R14: ffff978d98ca8680 R15: 00000000000016a9
FS:  0000000000000000(0000) GS:ffff9794ef6c0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffae57c0ca5047 CR3: 0000000113d5a004 CR4: 0000000000770ee0
PKRU: 55555554
Call Trace:
 qca_uart_setup+0x2cb/0x1390 [btqca]
 ? qca_read_soc_version+0x136/0x220 [btqca]
 qca_setup+0x288/0xab0 [hci_uart]
 hci_dev_do_open+0x1f3/0x780 [bluetooth]
 ? try_to_wake_up+0x1c1/0x4f0
 hci_power_on+0x3f/0x200 [bluetooth]
 process_one_work+0x1ec/0x380
 worker_thread+0x53/0x3e0
 ? process_one_work+0x380/0x380
 kthread+0x11b/0x140
 ? kthread_associate_blkcg+0xa0/0xa0
 ret_from_fork+0x1f/0x30
Modules linked in: llc ip_set nf_tables nfnetlink snd_soc_skl_hda_dsp(+) ip6table_filter snd_soc_hdac_hdmi ip6_tables qrtr_mhi iptable_filter snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic s>
 dell_wmi_sysman(+) dell_smbios snd dcdbas mhi vfat videobuf2_vmalloc i2c_i801 videobuf2_memops videobuf2_v4l2 dell_wmi_descriptor fat wmi_bmof soundcore i2c_smbus videobuf2_common libarc4 mei_me mei hid_se>
 i2c_hid_acpi i2c_hid video pinctrl_tigerlake fuse
CR2: ffffae57c0ca5047

This also seems to fix a failure to suspend due to the firmware
download on bootup getting interrupted by the crash:

Bluetooth: hci0: SSR or FW download time out
PM: dpm_run_callback(): acpi_subsys_suspend+0x0/0x60 returns -110
PM: Device serial0-0 failed to suspend: error -110
PM: Some devices failed to suspend, or early wake event detected

Fixes: 83e81961 ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: NConnor Abbott <cwabbott0@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For incoming SCO connection with transparent coding format, alt setting
of CVSD is getting applied instead of Transparent.

Before fix:
< HCI Command: Accept Synchron.. (0x01|0x0029) plen 21  #2196 [hci0] 321.342548
        Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd)
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
          Input Coding: Linear
          Input Data Format: 1's complement
          Input Sample Size: 8-bit
          # of bits padding at MSB: 0
          Air Coding Format: Transparent Data
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x003f
          HV1 may be used
          HV2 may be used
          HV3 may be used
          EV3 may be used
          EV4 may be used
          EV5 may be used
> HCI Event: Command Status (0x0f) plen 4               #2197 [hci0] 321.343585
      Accept Synchronous Connection Request (0x01|0x0029) ncmd 1
        Status: Success (0x00)
> HCI Event: Synchronous Connect Comp.. (0x2c) plen 17  #2198 [hci0] 321.351666
        Status: Success (0x00)
        Handle: 257
        Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x04
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)
........
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2336 [hci0] 321.383655
< SCO Data TX: Handle 257 flags 0x00 dlen 60            #2337 [hci0] 321.389558
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2338 [hci0] 321.393615
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2339 [hci0] 321.393618
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2340 [hci0] 321.393618
< SCO Data TX: Handle 257 flags 0x00 dlen 60            #2341 [hci0] 321.397070
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2342 [hci0] 321.403622
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2343 [hci0] 321.403625
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2344 [hci0] 321.403625
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2345 [hci0] 321.403625
< SCO Data TX: Handle 257 flags 0x00 dlen 60            #2346 [hci0] 321.404569
< SCO Data TX: Handle 257 flags 0x00 dlen 60            #2347 [hci0] 321.412091
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2348 [hci0] 321.413626
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2349 [hci0] 321.413630
> SCO Data RX: Handle 257 flags 0x00 dlen 48            #2350 [hci0] 321.413630
< SCO Data TX: Handle 257 flags 0x00 dlen 60            #2351 [hci0] 321.419674

After fix:

< HCI Command: Accept Synchronou.. (0x01|0x0029) plen 21  #309 [hci0] 49.439693
        Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd)
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
          Input Coding: Linear
          Input Data Format: 1's complement
          Input Sample Size: 8-bit
          # of bits padding at MSB: 0
          Air Coding Format: Transparent Data
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x003f
          HV1 may be used
          HV2 may be used
          HV3 may be used
          EV3 may be used
          EV4 may be used
          EV5 may be used
> HCI Event: Command Status (0x0f) plen 4                 #310 [hci0] 49.440308
      Accept Synchronous Connection Request (0x01|0x0029) ncmd 1
        Status: Success (0x00)
> HCI Event: Synchronous Connect Complete (0x2c) plen 17  #311 [hci0] 49.449308
        Status: Success (0x00)
        Handle: 257
        Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x04
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #312 [hci0] 49.450421
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #313 [hci0] 49.457927
> HCI Event: Max Slots Change (0x1b) plen 3               #314 [hci0] 49.460345
        Handle: 256
        Max slots: 5
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #315 [hci0] 49.465453
> SCO Data RX: Handle 257 flags 0x00 dlen 60              #316 [hci0] 49.470502
> SCO Data RX: Handle 257 flags 0x00 dlen 60              #317 [hci0] 49.470519
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #318 [hci0] 49.472996
> SCO Data RX: Handle 257 flags 0x00 dlen 60              #319 [hci0] 49.480412
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #320 [hci0] 49.480492
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #321 [hci0] 49.487989
> SCO Data RX: Handle 257 flags 0x00 dlen 60              #322 [hci0] 49.490303
< SCO Data TX: Handle 257 flags 0x00 dlen 60              #323 [hci0] 49.495496
> SCO Data RX: Handle 257 flags 0x00 dlen 60              #324 [hci0] 49.500304
> SCO Data RX: Handle 257 flags 0x00 dlen 60              #325 [hci0] 49.500311
Signed-off-by: NKiran K <kiran.k@intel.com>
Signed-off-by: NLokendra Singh <lokendra.singh@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fix the following clang warning:

net/bluetooth/6lowpan.c:913:20: warning: unused function 'bdaddr_type'
[-Wunused-function].

net/bluetooth/6lowpan.c:106:35: warning: unused function
'peer_lookup_ba' [-Wunused-function].
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NJiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During command status or command complete event, the controller may set
ncmd=0 indicating that it is not accepting any more commands. In such a
case, host holds off sending any more commands to the controller. If the
controller doesn't recover from such condition, host will wait forever,
until the user decides that the Bluetooth is broken and may power cycles
the Bluetooth.

This patch triggers the hardware error to reset the controller and
driver when it gets into such state as there is no other wat out.
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NManish Mandlik <mmandlik@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In qca_power_shutdown() qcadev local variable is
initialized by hu->serdev.dev private data, but
hu->serdev can be NULL and there is a check for it.

Since, qcadev is not used before

	if (!hu->serdev)
		return;

we can move its initialization after this "if" to
prevent GPF.

Fixes: 5559904c ("Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()")
Cc: stable@vger.kernel.org # v5.6+
Cc: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: NPavel Skripkin <paskripkin@gmail.com>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

0x2B, 0x31 and 0x33 are reserved for future use but were not present in
the HCI to MGMT conversion table, this caused the conversion to be
incorrect for the HCI status code greater than 0x2A.
Reviewed-by: NMiao-chen Chou <mcchou@chromium.org>
Signed-off-by: NYu Liu <yudiliu@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When cmtp_attach_device fails, cmtp_add_connection returns the error value
which leads to the caller to doing fput through sockfd_put. But
cmtp_session kthread, which is stopped in this path will also call fput,
leading to a potential refcount underflow or a use-after-free.

Add a refcount before we signal the kthread to stop. The kthread will try
to grab the cmtp_session_sem mutex before doing the fput, which is held
when get_file is called, so there should be no races there.

Reported-by: Ryota Shiga
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If btusb_mtk_submit_wmt_recv_urb returns error, wc should be freed and
then error should be returned to prevent memory leak.

Addresses-Coverity: ("Prevent memory leak")
Fixes: 4cbb375e997d ("Bluetooth: btusb: Fixed too many in-token issue for Mediatek Chip.")
Signed-off-by: NMuhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support for Lite-On Mediatek Chip (MT7921)
Lite On VID = 04CA.

* /sys/kernel/debug/usb/devices
T:  Bus=01 Lev=03 Prnt=04 Port=01 Cnt=02 Dev#=  8 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3802 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
Signed-off-by: Nmark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch reduce in-token during download patch procedure.
Don't submit urb for polling event before sending hci command.
Signed-off-by: Nmark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The call to alloc_skb with the GFP_KERNEL flag can return a null sk_buff
pointer, so add a null check to avoid any null pointer deference issues.

Addresses-Coverity: ("Dereference null return value")
Fixes: afd2daa2 ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When an MGMT_EV_DEVICE_CONNECTED event is reported back to the user
space we will set the flags to tell if the established connection is
outbound or not. This is useful for the user space to log better metrics
and error messages.
Reviewed-by: NMiao-chen Chou <mcchou@chromium.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NYu Liu <yudiliu@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fix the following coccicheck warning:

net/bluetooth/msft.c:37:6-13: WARNING use flexible-array member instead
net/bluetooth/msft.c:42:6-10: WARNING use flexible-array member instead
net/bluetooth/msft.c:52:6-10: WARNING use flexible-array member instead
Signed-off-by: NQiheng Lin <linqiheng@huawei.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Delete unneeded variable initialization.
Signed-off-by: NKai Ye <yekai13@huawei.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-06-25

This series contains updates to ice driver only.

Jesse adds support for tracepoints to aide in debugging.

Maciej adds support for PTP auxiliary pin support.

Victor removes the VSI info from the old aggregator when moving the VSI
to another aggregator.

Tony removes an unnecessary VSI assignment.

Christophe Jaillet fixes a memory leak for failed allocation in
ice_pf_dcb_cfg().
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When smc_sendmsg() is called before the SMC socket initialization has
completed, smc_tx_sendmsg() will access un-initialized fields of the
SMC socket which results in a null-pointer dereference.
Fix this by checking the socket state first in smc_tx_sendmsg().

Fixes: e0e4b8fa ("net/smc: Add SMC statistics support")
Reported-by: syzbot+5dda108b672b54141857@syzkaller.appspotmail.com
Reviewed-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NGuvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2021-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.14

Second, and most likely the last, set of patches for v5.14. mt76 and
iwlwifi have most patches in this round, but rtw88 also has some new
features. Nothing special really standing out.

mt76

* mt7915 MSI support

* disable ASPM on mt7915

* mt7915 tx status reporting

* mt7921 decap offload

rtw88

* beacon filter support

* path diversity support

* firmware crash information via devcoredump

* quirks for disabling pci capabilities

mt7601u

* add USB ID for a XiaoDu WiFi Dongle

ath11k

* enable support for QCN9074 PCI devices

brcmfmac

* support parse country code map from DeviceTree

iwlwifi

* support for new hardware

* support for BIOS control of 11ax enablement in Russia

* support UNII4 band enablement from BIOS
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The newly implemented fwnode_mdbiobus_register turned out to be
problematic - in case the fwnode_/of_/acpi_mdio are built as
modules, a dependency cycle can be observed during the depmod phase of
modules_install, eg.:

depmod: ERROR: Cycle detected: fwnode_mdio -> of_mdio -> fwnode_mdio
depmod: ERROR: Found 2 modules in dependency cycles!

OR:

depmod: ERROR: Cycle detected: acpi_mdio -> fwnode_mdio -> acpi_mdio
depmod: ERROR: Found 2 modules in dependency cycles!

A possible solution could be to rework fwnode_mdiobus_register,
so that to merge the contents of acpi_mdiobus_register and
of_mdiobus_register. However feasible, such change would
be very intrusive and affect huge amount of the of_mdiobus_register
users.

Since there are currently 2 users of ACPI and MDIO
(xgmac_mdio and mvmdio), withdraw the fwnode_mdbiobus_register
and roll back to a simple 'if' condition in affected drivers.

Fixes: 62a6ef6a ("net: mdiobus: Introduce fwnode_mdbiobus_register()")
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If this 'kzalloc()' fails we must free some resources as in all the other
error handling paths of this function.

Fixes: 348048e7 ("ice: Implement iidc operations")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

ice_get_vf_vsi() is being called twice for the same VSI. Remove the
unnecessary call/assignment.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>

Remove the VSI info from previous aggregator after moving the VSI to a
new aggregator.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The E810 device supports programmable pins for enabling both input and
output events related to the PTP hardware clock. This includes both
output signals with programmable period, as well as timestamping of
events on input pins.

Add support for enabling these using the CONFIG_PTP_1588_CLOCK
interface.

This allows programming the software defined pins to take advantage of
the hardware clock features.
Signed-off-by: NMaciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

This patch adds build and driver logic for the "mlxbf_gige"
Ethernet driver from Mellanox Technologies. The second
generation BlueField SoC from Mellanox supports an
out-of-band GigaBit Ethernet management port to the Arm
subsystem.  This driver supports TCP/IP network connectivity
for that port, and provides back-end routines to handle
basic ethtool requests.

The driver interfaces to the Gigabit Ethernet block of
BlueField SoC via MMIO accesses to registers, which contain
control information or pointers describing transmit and
receive resources.  There is a single transmit queue, and
the port supports transmit ring sizes of 4 to 256 entries.
There is a single receive queue, and the port supports
receive ring sizes of 32 to 32K entries. The transmit and
receive rings are allocated from DMA coherent memory. There
is a 16-bit producer and consumer index per ring to denote
software ownership and hardware ownership, respectively.

The main driver logic such as probe(), remove(), and netdev
ops are in "mlxbf_gige_main.c".  Logic in "mlxbf_gige_rx.c"
and "mlxbf_gige_tx.c" handles the packet processing for
receive and transmit respectively.

The logic in "mlxbf_gige_ethtool.c" supports the handling
of some basic ethtool requests: get driver info, get ring
parameters, get registers, and get statistics.

The logic in "mlxbf_gige_mdio.c" is the driver controlling
the Mellanox BlueField hardware that interacts with a PHY
device via MDIO/MDC pins.  This driver does the following:
  - At driver probe time, it configures several BlueField MDIO
    parameters such as sample rate, full drive, voltage and MDC
  - It defines functions to read and write MDIO registers and
    registers the MDIO bus.
  - It defines the phy interrupt handler reporting a
    link up/down status change
  - This driver's probe is invoked from the main driver logic
    while the phy interrupt handler is registered in ndo_open.

Driver limitations
  - Only supports 1Gbps speed
  - Only supports GMII protocol
  - Supports maximum packet size of 2KB
  - Does not support scatter-gather buffering

Testing
  - Successful build of kernel for ARM64, ARM32, X86_64
  - Tested ARM64 build on FastModels & Palladium
  - Tested ARM64 build on several Mellanox boards that are built with
    the BlueField-2 SoC.  The testing includes coverage in the areas
    of networking (e.g. ping, iperf, ifconfig, route), file transfers
    (e.g. SCP), and various ethtool options relevant to this driver.
Signed-off-by: NDavid Thompson <davthompson@nvidia.com>
Signed-off-by: NAsmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: NLiming Sun <limings@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is modeled after one by Scott Peterson for i40e.

Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.

Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.

Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.
Co-developed-by: NBen Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: NBen Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:

bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus

It is not just coming too late, there is also no way for the module
loader to figure out the dependency between GENET and its MDIO bus
driver unless we provide this MODULE_SOFTDEP hint.

This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to fix this issue.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Fixes: 9a4e7969 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: NJian-Hong Pan <jhp@endlessos.org>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

parameter dst always points to null.
Signed-off-by: Nzhang kai <zhangkaiheb@126.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>