In case a qdisc is used on a vrf device, we need to use different
lockdep classes to avoid false positives.

Use the new netdev_lockdep_set_classes() generic helper.
Reported-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is time to add netdev_lockdep_set_classes() helper
so that lockdep annotations per device type are easier to manage.

This removes a lot of copies and missing annotations.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm hitting 5 second timeout in rndis_filter_set_rss_param() while setting
RSS parameters for the device. When this happens we end up returning
-ETIMEDOUT from the function and rndis_filter_device_add() falls back to
setting

        net_device->max_chn = 1;
        net_device->num_chn = 1;
        net_device->num_sc_offered = 0;

but after a moment the rndis request succeeds and subchannels start to
appear. netvsc_sc_open() does unconditional nvscdev->num_sc_offered-- and
it becomes U32_MAX-1. Consequent rndis_filter_device_remove() will hang
while waiting for all U32_MAX-1 subchannels to appear and this is not
going to happen.

The immediate issue could be solved by adding num_sc_offered > 0 check to
netvsc_sc_open() but we're getting out of sync with the host and it's not
easy to adjust things later, e.g. in this particular case we'll be creating
queues without a user request for it and races are expected. Same applies
to other parts of the driver which have the same completion timeout.

Following the trend in drivers/hv/* code I suggest we remove all these
timeouts completely. As a guest we can always trust the host we're running
on and if the host screws things up there is no easy way to recover anyway.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add l3mdev rule per address family when the first VRF device is
created. The rules are installed with a default preference of 1000.
Users can replace the default rule as desired.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.

We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the interfaces for ieee/cee dcbnl callbacks and registers
them with the kernel.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the implementation for both cee/ieee dcbnl callbacks by
using the qed query/config APIs.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Query API reads the dcbx data from the device shared memory and return it
to the caller. The config API configures the user provided dcbx values on
the device, and initiates the dcbx negotiation with the peer.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CONFIG_ prefix should only be used for options which
can be configured through Kconfig and not for guarding headers.
Signed-off-by: NAndreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current code "ent_per_page" could be more than "conn_num" making
"conn_num" negative after the subtraction.  In the next iteration
through the loop then the negative is treated as a very high positive
meaning we don't put a limit on "ent_num".  It could lead to memory
corruption.

Fixes: dbb799c3 ('qed: Initialize hardware for new protocols')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:

    $ ip addr show dev eth1
    4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
        link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
        inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
           valid_lft forever preferred_lft forever
        inet6 2100:1::1/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
           valid_lft forever preferred_lft forever

    $ ping6 -c1 -I red 2100:1::1
    ping6: Warning: source address might be selected on device other than red.
    PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
    64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms

ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for locally originated traffic to VRF-local addresses. If
destination device for an skb is the loopback or VRF device then set
its dst to a local version of the VRF cached dst_entry and call netif_rx
to insert the packet onto the rx queue - similar to what is done for
loopback. This patch handles IPv4 support; follow on patch handles IPv6.

With this patch, ping, tcp and udp packets to a local IPv4 address are
successfully routed:

    $ ip addr show dev eth1
    4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
        link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
        inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
           valid_lft forever preferred_lft forever
        inet6 2100:1::1/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
           valid_lft forever preferred_lft forever

    $ ping -c1 -I red 10.100.1.1
    ping: Warning: source address might be selected on device other than red.
    PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data.
    64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms

This patch also enables use of IPv4 loopback address on the VRF device:
    $ ip addr add dev red 127.0.0.1/8

    $ ping -c1 -I red 127.0.0.1
    PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data.
    64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the stripping of the ethernet header from is_ip_tx_frame into the
ipv4 and ipv6 outbound functions and collapse vrf_send_v4_prep into
vrf_process_v4_outbound.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a single bit (__QDISC___STATE_RUNNING)
in sch->__state, use a seqcount.

This adds lockdep support, but more importantly it will allow us
to sample qdisc/class statistics without having to grab qdisc root lock.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we do not distribute queue resources to enable RSS for VFs
in multi-channel/partition configurations.
Fix this by having each PF(SRIOV capable) calculate it's share of the
15 RSS Policy Tables available per port before provisioning resources for
all the VFs.
This  proportional share calculation is done based on division of the
PF's MAX VFs with the Total MAX VFs on that port. It also needs to
learn about the no: of NIC PFs on the port and subtract that from
the 15 RSS Policy Tables on the port.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk does support wake-up from ACPI shutdown state - S5, provided the
platform supports it (like Auxiliary power source etc). The changes listed
below are done to fix this.

1) There's no need to defer the HW configuration of WOL to be_suspend().
Remove this in be_suspend() and move it to be_set_wol() ethtool function
so it is configured directly in the context of ethtool. This automatically
takes care of the shutdown case.

2) The driver incorrectly uses WOL_CAP field in the FW response to
get_acpi_wol_cap() command, to determine if WOL is enabled. Instead the
driver must rely on the macaddr field in the response to infer WOL state.

3) In be_get_config() during init, if we find that WOL is enabled in FW,
call pci_enable_wake() to enable pmcsr.pme_en bit. This is needed to
support persistent WOL configuration provided by the FW in some platforms.

4) Remove code in be_set_wol() that writes to PCICFG_PM_CONTROL_OFFSET
to set pme_en bit; pci_enable_wake() sets that.

Fixes: 028991e4 ("Enabling Wake-on-LAN is not supported in S5 state")
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the PF driver provisions resources for VFs, it currently only looks
at max RSS queues available to calculate the number of VF queue pairs.
This logic breaks when there are less number of TX-queues than RSS-queues.
This patch fixes this problem by using the max-TXQs available in the
PF-pool in the calculations. As a part of this change the
be_calculate_vf_qs() routine is renamed as be_calculate_vf_res() and the
code that calculates limits on other related resources is moved here to
contain all resource calculation code inside one routine.
Signed-off-by: NSuresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver add hdlc support for Freescale QUICC Engine.
It support NMSI and TSA mode.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QE has module to support TDM, some other protocols
supported by QE are based on TDM.
add a qe-tdm lib, this lib provides functions to the protocols
using TDM to configurate QE-TDM.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tdm clock configuration in both qe clock system and ucc
fast controller.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rx_sync and tx_sync are used by QE-TDM mode,
add them to struct ucc_fast_info.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a future VF would send the PF an unknown message, the PF today would
not send a reply. This would have 2 bad effects:
  a. VF would have to timeout on the request.
  b. If VF were to send an additional message to PF, firmware would mark
     it as malicious.

Instead, if there's some valid reply-address on the message - let the PF
answer and tell the VF it doesn't know the message.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only limitation relating to MACs the PF enforce today on its VFs
is in case it has a forced-unicast MAC address for them, in which case
they can't configure other unicast addresses.
Specifically, the PF isn't enforcing the number of MAC addresse a VF can
configure regardless of the nubmer of such filters agreed upon by PF and
VF during the acquisition process.

PF's shadow-config is now extended to also contain information about its
VFs' unicast addresses configuration, allowing such enforcement.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today, the VF is aware of its queues context-ids, and calculates the
doorbell address when opening its queues on its own.
The configuration of doorbells in HW can sometime in the future be changed
by the PF [hw has several configurable features that might affect doorbell
addresses, e.g., dpm support], this would break compatibility with older
VFs as their calculated doorbell addresses would be incorrect for such a
configuration.

In order to avoid such a backward compatibility failure, let the PF make
the calculation of the doorbell offset based on the context-id, and pass
that to the VF.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several requests the VF can make toward the PF which the driver
would pass to firmware without checking the validity first - specifically,
opening queues and updating vports. Such configurations might cause the
firmware to assert.

This adds validation of the legality of said configurations on the PF side
before passing it onward via ramrod to firmware.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the goals of the vf's first message to the PF [acquire]
is to learn about the number of resources available to it [macs, vlans,
etc.]. This is done via negotiation - the VF requires a set of resources,
which the PF either approves or disaproves and sends a smaller set of
resources as alternative. In this later case, the VF is then expected to
either abort the probe or re-send the acquire message with less
required resources.

While this infrastructure exists since the initial submision of qed
SRIOV support, it's in fact completely inoperational - PF isn't really
looking into the resources the VF has asked for and is never going to
reply to the VF that it lacks resources.

This patch addresses this flow, fixing it and allowing the PF and VF
to actually agree on a set of resources.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current driver require an exact match between VF and PF storm firmware;
Any difference would fail the VF acquire message, causing the VF probe
to be aborted.

While there's still dependencies between the two, the recent FW submission
has relaxed the match requirement - instead of an exact match, there's now
a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their
major number can co-exist even if their minor is different.

In order to accomadate this change some changes in the vf-start init flow
had to be made, as the VF start ramrod now has to be sent only after PF
learns which fastpath HSI its VF is requiring.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't stop rx polling socket during rx processing, this will lead
unnecessary wakeups from under layer net devices (E.g
sock_def_readable() form tun). Rx will be slowed down in this
way. This patch avoids this by stop polling socket during rx
processing. A small drawback is that this introduces some overheads in
light load case because of the extra start/stop polling, but single
netperf TCP_RR does not notice any change. In a super heavy load case,
e.g using pktgen to inject packet to guest, we get about ~8.8%
improvement on pps:

before: ~1240000 pkt/s
after:  ~1350000 pkt/s
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workitem viz
(&db_wq->wk.work which maps to check_db_timeout) is involved
in normal device operation. WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.

flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workitem viz
(&cwq->wk.work which maps to oct_poll_req_completion) is involved
in normal device operation. WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.

flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds the feature bit and associated mtu device entry for the
virtio network device.  When a virtio device comes up, it checks the
feature bit for the VIRTIO_NET_F_MTU feature.  If such feature bit is
enabled, the driver will read the advised MTU and use it as the initial
value.
Signed-off-by: NAaron Conole <aconole@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 2fb7ea45.

It results in build errors because ip6_input is not a
symbol exported to modules.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:

    $ ip addr show dev eth1
    4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
        link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
        inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
           valid_lft forever preferred_lft forever
        inet6 2100:1::1/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
           valid_lft forever preferred_lft forever

    $ ping6 -c1 -I red 2100:1::1
    ping6: Warning: source address might be selected on device other than red.
    PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
    64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms

ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for locally originated traffic to VRF-local addresses. If
destination device for an skb is the loopback or VRF device then set
its dst to a local version of the VRF cached dst_entry and call netif_rx
to insert the packet onto the rx queue - similar to what is done for
loopback. This patch handles IPv4 support; follow on patch handles IPv6.

With this patch, ping, tcp and udp packets to a local IPv4 address are
successfully routed:

    $ ip addr show dev eth1
    4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
        link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
        inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
           valid_lft forever preferred_lft forever
        inet6 2100:1::1/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
           valid_lft forever preferred_lft forever

    $ ping -c1 -I red 10.100.1.1
    ping: Warning: source address might be selected on device other than red.
    PING 10.100.1.1 (10.100.1.1) from 10.100.1.1 red: 56(84) bytes of data.
    64 bytes from 10.100.1.1: icmp_seq=1 ttl=64 time=0.057 ms

This patch also enables use of IPv4 loopback address on the VRF device:
    $ ip addr add dev red 127.0.0.1/8

    $ ping -c1 -I red 127.0.0.1
    PING 127.0.0.1 (127.0.0.1) from 127.0.0.1 red: 56(84) bytes of data.
    64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.058 ms
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the stripping of the ethernet header from is_ip_tx_frame into the
ipv4 and ipv6 outbound functions. If the packet is destined to a local
address the header is retained since the packet is sent back to netif_rx.

Collapse vrf_send_v4_prep into vrf_process_v4_outbound.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only caller rndis_filter_device_add() has 'struct net_device' pointer
already.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We unpack 'struct net_device' in netvsc_set_mac_addr() to get to
'struct hv_device' pointer which we use in rndis_filter_set_device_mac()
to get back to 'struct net_device'.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both rndis_filter_open()/rndis_filter_close() use struct hv_device to
reach to struct netvsc_device only and all callers have it already.
While on it, rename net_device to nvdev in rndis_filter_open() as
net_device is misleading.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it easier to get 'struct netvsc_device' from 'struct net_device' and
'struct hv_device' by introducing inline helpers.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_device_ctx is assigned in the very beginning of the function and 'net'
pointer doesn't change.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>