Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Enable cpufreq on Genesi efika platforms
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch declares regulators for the efikamx. Use it also to power off the
efikamx.
Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to
power off by setting GPIO 4 13 to high level instead of powering off through
the mc13892.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

i.MX23 Reference Manaul starts auart index from 1 than 0.  Changing
the index to start from 0 requires corresponding changes on base
address, irq, and iomux definitions, and will probably confuse people
who reads codes and hardware documents together.

This patch introduced the field 'hwid' to distinguish the driver id
and controller id.  These two ids are different on mx23 while
identical on mx28.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

i.MX23 Reference Manual names auart irq differently from i.MX28.
This patch is to align the naming with mx28, so that some device
registration codes can be shared.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Fixes 2 small regressions of recent iomux changes:
 - current MX51_PAD_UART2_TXD__UART2_TXD declaration overwrites
   IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT register (0x09ec) and prevent
   UART2 Rx from working properly.
   (Tested on my custom i.MX51 board where UART2 is used as console)
 - current MX51_PAD_USBH1_DATA2__UART2_TXD declaration also has the same problem.
   (Not tested)
Signed-off-by: NJulien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The arguments to these callbacks were changed in

	e981a302 (ARM: mx3: irq_data conversion.)

but the comments were not adapted.

Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

mxc_board_init is too generic to be useful.  Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently we have a mxc_initialize_usb_hw which is called on every
i.MX SoC. This function dispatches the different SoC types, which
is quite ugly. This patch moves the SoC specific USB initialization
to their correspondive mach directories.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the memory
mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This fixes:

	arch/arm/mach-mx3/mach-mx31_3ds.c:249: warning: 'mx31_3ds_host2_init' defined but not used
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

FREQ is a ridiculously short name for a platform-specific macro in a
generic header, and it now conflicts with an enumeration in the
gspca/ov519 driver.

Also delete conditional reference to ixp4xx_get_board_tick_rate()
which is not defined anywhere.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>

Queues should be empty when released, if not, there is a safety valve.
Make sure the queue is usable after it triggers.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>

The last register is at offset 0xa8 making the resource end to be 0xac - 1
instead of 0xb0 - 1.
Signed-off-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Panda uses both twl6030 otg phy(vbus, id) and internal
phy(data lines, DP/DM), so removes usb_nop_xceiv_register to make
twl6030 otg driver working since current otg code only supports
one global transceiver. Otherwise, musb doesn't work without
the remove.
Reviewd-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes bug introduced in revision:

f8e9e984
omap1: DMA: move LCD related code from plat-omap to mach-omap1

The code introduced by this patch didn't consider any other CPUs but OMAP1510,
which rendered OMAP310 -- which has the same LCD controller -- non-working. Use
cpu_is_omap15xx() instead of cpu_is_omap1510() to squash this issue.

Bug found on Palm Zire 71 hardware.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes a wrongly used lcd enable pin.

The Devkit8000 uses twl4030_ledA configured as output gpio only for
the lcd enable line. twl4030_gpio.1 is used through the generic
gpio functions while ledA is used via low level twl4030 calls.

This patch removes the low level calls and use the generic gpio functions
for initialization and use of ledA. This patch also fixes a bug where the
lcd would not power down when blanking.

Further this patch fixes an indentation issue. The comment line uses
eight whitespace and is replaced with a hard tab.

gpio_request + gpio_direction_output are replaced with gpio_request_one.
The return value of gpio_request_one is used to set the value of the
gpio to -EINVAL when unsuccessful, so that gpio_is_valid can detect the
unsuccessful request. But already successful requested gpios are not freed.
Reported-by: NDaniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove duplicated #include('s) in
  arch/arm/mach-omap1/time.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Free allocated memory on error exit.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the commit 75790251 (regulator:
Factor out voltage set operation into a separate function) fixed voltage
regulator setup will fail if there are voltage constraints defined. This
made MMC unusable on this board. Fix by just deleting those redundant
constraints.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Reviewed-by: NJarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit b2878fa4 (ARM: mx28: update clock and device name for dual fec
support) added only the new lookups without removing the old one.

Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

On mx53_loco only UART1 is used and its signals go to connector J16.

Remove UART2 and UART3 as they are not used on this board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>