Previously I reported that the pata_pdc2027x PLL detection changes
in kernel 2.6.22 broke the driver on my PowerMac:

>pata_pdc2027x: Invalid PLL input clock 1691742kHz, give up!

This is followed by a number of errors and speed reduction
steps on the affected ports.

There are two bugs in pata_pdc2027x's PLL detection code:

1. The PLL counter's start value is read before the chip is
   put in "test mode". Outside of test mode the counter is
   halted, and on the PowerMac the counter is zero because
   the chip hasn't been initialised by its BIOS.

   The fix is to move the read of the start value to after
   test mode is started, but before the mdelay() in test mode.
   This also improves the precision of the PLL detection.

2. The code to compute the number of PLL decrements during the
   mdelay() in test mode fails to consider that the PLL counter
   only is 30 bits wide. If there is a wraparound, it will compute
   an incorrect and much too large value. On the PowerMac, the
   start count is zero, the end count is a large 30-bit value, so
   wraparound occurs and an out of bounds PLL clock is detected.

   The fix is to mask the (start - end) computation to 30 bits.

While debugging this I also noticed that pdc_read_counter()
reads the two halves of the 30-bit PLL counter as 16-bit values,
and then combines them as if the halves only are 15 bits wide.
To avoid confusion, the halves should be read as 15-bit values.

This patch implements all three changes. It fixes the PLL detection
failure on my PowerMac, and doesn't cause any regressions on an x86
with an identical card.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If revalidation fails because device has different n_sectors after
configuration the original n_sectors should be restored before failing
revalidation.  Without this fix, n_sectors difference will incorrectly
and silently pass revalidation when revalidation is retried.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The NUMA layer only supports NUMA policies for the highest zone.  When
ZONE_MOVABLE is configured with kernelcore=, the the highest zone becomes
ZONE_MOVABLE.  The result is that policies are only applied to allocations
like anonymous pages and page cache allocated from ZONE_MOVABLE when the
zone is used.

This patch applies policies to the two highest zones when the highest zone
is ZONE_MOVABLE.  As ZONE_MOVABLE consists of pages from the highest "real"
zone, it's always functionally equivalent.

The patch has been tested on a variety of machines both NUMA and non-NUMA
covering x86, x86_64 and ppc64.  No abnormal results were seen in
kernbench, tbench, dbench or hackbench.  It passes regression tests from
the numactl package with and without kernelcore= once numactl tests are
patched to wait for vmstat counters to update.

akpm: this is the nasty hack to fix NUMA mempolicies in the presence of
ZONE_MOVABLE and kernelcore= in 2.6.23.  Christoph says "For .24 either merge
the mobility or get the other solution that Mel is working on.  That solution
would only use a single zonelist per node and filter on the fly.  That may
help performance and also help to make memory policies work better."
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Acked-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Tested-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: NChristoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

au1100fb_fb_blank() should come before au1100fb_setmode().

drivers/video/au1100fb.c: In function 'au1100fb_setmode':
drivers/video/au1100fb.c:211: error: implicit declaration of function 'au1100fb_fb_blank'
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/video/console/newport_con.c: In function `newport_console_init':
drivers/video/console/newport_con.c:743: warning: return makes integer from pointer without a cast

Although one wonders whether that should have been -ENODEV...

Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In file included from drivers/video/console/newport_con.c:16:
include/linux/selection.h:16: warning: "struct tty_struct" declared inside parameter list
include/linux/selection.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the correct fix according to Paul Mackerras and allows an
allyesconfig on PPC64 to build.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Xen i386 xen-head.S fix sections mixup

xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.

Updates:

- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
  does its own push/popsection to put things into the appropriate .note* section
  anyway.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

de_thread:

	if (atomic_read(&oldsighand->count) <= 1)
		BUG_ON(atomic_read(&sig->count) != 1);

This is not safe without the rmb() in between.  The results of two
correctly ordered __exit_signal()->atomic_dec_and_test()'s could be seen
out of order on our CPU.

The same is true for the "thread_group_empty()" case, __unhash_process()'s
changes could be seen before atomic_dec_and_test(&sig->count).

On some platforms (including i386) atomic_read() doesn't provide even the
compiler barrier, in that case these checks are simply racy.

Remove these BUG_ON()'s. Alternatively, we can do something like

	BUG_ON( ({ smp_rmb(); atomic_read(&sig->count) != 1; }) );
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor tweaks to rtc-max6902: make it hotplug correctly, and fix a few
space-before-tab whitespace botches.  This driver has no current in-tree
users, so the hotplug fix changes the driver name.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Print a big fat warning and do what is necessary to continue if a node is
marked as up (meaning either node is online (upstream) or node has memory
(Andrew's tree)) but allocations from the node do not succeed.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SLUB is using atomic_read() for variables declared atomic_long_t.
Switch to atomic_long_read().
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This one-liner patch fixes a bug in drivers/auxdisplay/cfag12864b.c

At cfag12864b_init(), the driver tries to kalloc some memory in the
variable cfag12864b_cache.

Then, as usual, it checks if the call failed. However, it checks
cfag12864b_buffer instead.

This patch changes the "cfag12864b_buffer" to "cfag12864b_cache" so the
correct variable is checked.
Signed-off-by: NMiguel Ojeda <maxextreme@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add PCI IDs for the onchip UARTs on PA Semi PWRficient.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Due to inconsistent locking in the VFS between calls to lookup and
revalidate deadlock can occur in the automounter.

The inconsistency is that the directory inode mutex is held for both lookup
and revalidate calls when called via lookup_hash whereas it is held only
for lookup during a path walk.  Consequently, if the mutex is held during a
call to revalidate autofs4 can't release the mutex to callback the daemon
as it can't know whether it owns the mutex.

This situation happens when a process tries to create a directory within an
automount and a second process also tries to create the same directory
between the lookup and the mkdir.  Since the first process has dropped the
mutex for the daemon callback, the second process takes it during
revalidate leading to deadlock between the autofs daemon and the second
process when the daemon tries to create the mount point directory.

After spending quite a bit of time trying to resolve this on more than one
occassion, using rather complex and ulgy approaches, it turns out that just
delaying the hashing of the dentry until the create operation works fine.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.

By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line.  However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.

This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a raid1 array is reshaped (number of drives changed), the list of devices
is compacted, so that slots for missing devices are filled with working
devices from later slots.  This requires the "rd%d" symlinks in sysfs to be
updated.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 17571284 was slightly bad.  If an array
has a write-intent bitmap, and you remove a drive, then readd it, only the
changed parts should be resynced.  However after the above commit, this only
works if the array has not been shut down and restarted.

This is because it sets 'fullsync' at little more often than it should.  This
patch is more careful.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In case bus master driver provided bogus value as its private data, search
can be incorrect.  Problem found by Adrian Bunk.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It seems a simple mistake was made when converting follow_hugetlb_page()
over to the VM_FAULT flags bitmasks (in "mm: fault feedback #2", commit
83c54070).

By using the wrong bitmask, hugetlb_fault() failures are not being
recognized.  This results in an infinite loop whenever follow_hugetlb_page
is involved in a failed fault.
Signed-off-by: NAdam Litke <agl@us.ibm.com>
Acked-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Get module reference on open() by generic HDLC to prevent module from
unloading while interface is active.
Signed-off-by: NPaul Fulghum <paulkf@microgate.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Skip calling cache_free_alien() when the platform is not numa capable.
This will avoid cache misses that happen while accessing slabp (which is
per page memory reference) to get nodeid.  Instead use a global variable to
skip the call, which is mostly likely to be present in the cache.

This gives a 0.8% performance boost with the database oltp workload on a
quad-core SMP platform and by any means the number is not small :)
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Acked-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

trivial change: fix warning
Signed-off-by: NMijo Safradin <safradin@de.ibm.com>
Acked-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With this patch any thread can dequeue its own private signals via signalfd,
even if it was created by another sub-thread.

To do so, we pass "current" to dequeue_signal() if the caller is from the same
thread group. This also fixes the scheduling of posix timers broken by the
previous patch.

If the caller doesn't belong to this thread group, we can't handle __SI_TIMER
case properly anyway. Perhaps we should forbid the cross-process signalfd usage
and convert ctx->tsk to ctx->sighand.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dequeue_signal:

	if (__SI_TIMER) {
		spin_unlock(&tsk->sighand->siglock);
		do_schedule_next_timer(info);
		spin_lock(&tsk->sighand->siglock);
	}

Unless tsk == curent, this is absolutely unsafe: nothing prevents tsk from
exiting. If signalfd was passed to another process, do_schedule_next_timer()
is just wrong.

Add yet another "tsk == current" check into dequeue_signal().

This patch fixes an oopsable bug, but breaks the scheduling of posix timers
if the shared __SI_TIMER signal was fetched via signalfd attached to another
sub-thread. Mostly fixed by the next patch.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sys_timer_create() sets ->it_process and unlocks ->siglock, then checks
tmr->it_sigev_notify to define if get_task_struct() is needed.

We already passed ->it_id to the caller, another thread can delete this timer
and free its memory in between.

As a minimal fix, move this code under ->siglock, sys_timer_delete() takes it
too before calling release_posix_timer().  A proper serialization would be to
take ->it_lock, we add a partly initialized timer on posix_timers_id, not
good.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

timer_delete does:
	lock_timer();
	timer->it_process = NULL;
	unlock_timer();
	release_posix_timer();

timer->it_process is checked in lock_timer() to prevent access to a
timer, which is on the way to be deleted, but the check happens after
idr_lock is dropped. This allows release_posix_timer() to delete the
timer before the lock code can check the timer:

  CPU 0				CPU 1

  lock_timer();
  timer->it_process = NULL;
  unlock_timer();
				lock_timer()
					spin_lock(idr_lock);
					timer = idr_find();
					spin_lock(timer->lock);
					spin_unlock(idr_lock);
  release_posix_timer();
	spin_lock(idr_lock);
	idr_remove(timer);
	spin_unlock(idr_lock);
	free_timer(timer);
					if (timer->......)

Change the locking to prevent this.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().

Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k/mac: Make mac_hid_mouse_emulate_buttons() declaration visible

drivers/char/keyboard.c: In function 'kbd_keycode':
drivers/char/keyboard.c:1142: error: implicit declaration of function 'mac_hid_mouse_emulate_buttons'

The forward declaration of mac_hid_mouse_emulate_buttons() is not visible on
m68k because it's hidden in the middle of a big #ifdef block.

Move it to <linux/kbd_kern.h>, correct the type of the second parameter, and
include <linux/kbd_kern.h> where needed.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

zorro: Make the sysfs `config' attribute read-only, as you cannot write to it
(there's no .write function neither).
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k: Fix a few hickups in drivers/scsi/Kconfig
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Don't include RODATA into text segment as it includes the kallsyms data and
can cause spurious link failures (layout differences can change the number of
symbols in kallsyms, i.e.  when a symbol is equal to _etext it's not
included).
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the needed constants and defines to activate the existing code.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k: Use _AC() instead of #ifdef __ASSEMBLY__ hackery when needed, remove
hackery when unused.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When suspend is ever implemented for pmu68k it really should follow the
generic pm_ops concept and not mirror the platform-specific /dev/pmu
device with ioctls on it. Hence, this patch removes the unused code there;
should the implementers need it they can look at via-pmu.c and/or the
history of the file.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove an unnecessary m68k_memoffset export and initialization
Signed-off-by: NRoman Zippel <zippel@linux-m68k.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kill a superfluous extern declaration
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k: <asm/page.h> needs <linux/compiler.h> because of __attribute_const__
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The new exec code inserts an accounted vma into an mm struct which is not
current->mm.  The existing memory check code has a hard coded assumption
that this does not happen as does the security code.

As the correct mm is known we pass the mm to the security method and the
helper function.  A new security test is added for the case where we need
to pass the mm and the existing one is modified to pass current->mm to
avoid the need to change large amounts of code.

(Thanks to Tobias for fixing rejects and testing)
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: WU Fengguang <wfg@mail.ustc.edu.cn>
Cc: James Morris <jmorris@redhat.com>
Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The new rtc-m41t80 driver name doesn't match its module name, which
prevents it from properly hotplugging.  Since it's new, no platforms yet
depend on that name ...  so this patch fixes the driver name to match its
module name, rather than going the other way around with a MODULE_ALIAS().

NOTE: This sort of bug is a new thing to watch out for with new-style I2C
drivers; previously I2C couldn't hotplug.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>