Now that we have a different clock representation, switch to it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The sunxi-ng clock driver is useless for other architectures.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add support for the clock unit found in the A23. Due to the similarities
with the A33, it also shares its clock IDs to allow sharing the DTSI.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

This commit introduces the clocks found in the Allwinner A33 CCU.

Since this SoC is very similar to the A23, and we share a significant share
of the DTSI, the clock IDs that are going to be used will also be shared
with the A23, hence the name of the various header files.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Add support for the class with a single factor, N, being a multiplier.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Add a new macro to declare muxes based on a table and a gate.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Some dividers might have a maximum value that is lower than the width of
the register.

Add a field to _ccu_div to handle those case properly. If the field is set
to 0, the code will assume that the maximum value is the maximum one that
can be used with the field register width.

Otherwise, we'll use whatever value has been set.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

The internal _ccu_div structure is meant to be embedded into other
structures to combine the various dividers and to form the clock classes
support.

Start to document those structures by using kerneldoc.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add some macros to ease the declaration of clocks that are using them.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Guangzhou FriendlyARM Computer Tech Co., Ltd is a Chinese ARM board vendor.
Signed-off-by: NJames Pettigrew <james@innovum.com.au>
Reviewed-by: NRask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: NJames Pettigrew <james@innovum.com.au>
Reviewed-by: NRask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Most of the sun8i q8 boards have an SDIO wifi controller, on the
variants which use an USB wifi controller, this will result in a
couple of error msg-s in dmesg when proving the sdio bus and
an used mmc controller.

The best way to deal with wifi on this boards really is to simply
let the kernel auto-detect usb or sdio wifi controllers, so we
will just have to live with the few errors in dmesg.

This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and
RTL8189FTV wifi controllers.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.

Note currently the dts is pretty much empty (except for including the
pc-plus dts), I've a local patch which enables the emac actually making
this dts different from the pc-plus one, but that needs the h3 emac
driver to get merged first.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Update the sun8i-h3-orangepi-plus.dts model string to reflect that it
is valid for both the Orange Pi Plus and the Orange Pi Plus 2.

This is also meant to help users realize that it is not valid for
the new Orange Pi Plus 2E, which will get its own dts.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMilo Kim <woogyom.kim@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features
volume buttons, micro-usb otg, headphone connector and a power button.

On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there
is also a accompanied board which has a Goodix GT9271 soldered.

As this board is desired to create tablets with a Home key dealed by
GT9271, a LED is present at the front panel at the position of the
Home key.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The R_PIO device node is missing #interrupt-cells, which causes
interrupt parsing to fail to match it as a valid interrupt controller.

Add #interrupt-cells to it. Also remove the unnecesary #address-cells
and #size-cells.

Fixes: 1ac56a6d ("ARM: dts: sun9i: Add A80 R_PIO pin controller device
		      node")
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Rename the reference-design-tablet touchscreen node from gsl1680 to
touchscreen, all? tablets seem to use the same power and interrupt
gpio-s, but not all tablets use a gsl1680 controller making the
gsl1680 name somewhat misleading.

Also move the reg and compatible property to the actual tablet dts
as they may differ per tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13
tablet, with micro-usb (otg), headphone and micro-sd slots on the
outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.

Note currently the dts for this is somewhat empty. This will change
once we add support for the touchscreen and accelerometer.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This results in a nice cleanup :)
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi
module soldered on the PCB, so there enabling ohci1 is not necessary.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The polaroid-mid2407 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A23/A33 has a NAND controller which can now be used properly.

Add a device node for it.

The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.

Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html )
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a new style driver for the clock control unit in Allwinner A31/A31s.

A few clocks are still missing:

    - MIPI PLL's HDMI mode support
    - EMAC clock
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

On sunxi we support cpufreq by changing the clock rate of PLL-CPU.
It's possible the clock output of the PLL goes out of the CPU's
operational limits when the PLL's multipliers / dividers are changed
and it hasn't stabilized yet. This would result in the CPU hanging.

To circumvent this, we temporarily switch the CPU mux clock to another
stable clock before the rate change, and switch it back after the PLL
stabilizes. This is done with clk notifiers registered on the PLL.

This patch adds common functions for notifiers to reparent mux clocks.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some clocks on the A31 have fixed pre-dividers on multiple parents.
Add support for them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some clock muxes have holes, i.e. invalid or unconnected inputs,
between parent mux values.

Add support for specifying a mux table to map clock parents to
mux values.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Rename the internal mux macro to be consistent with the other internal
structure macros.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Just like with a13/a23/a33 most a31 tablets are derived from the same
reference design. Add a .dtsi file with all the common bits to avoid
endless copy and pasting of these.

The sun6i-reference-design-tablet.dtsi this commit adds is a copy
of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits
removed / left in sun6i-a31s-colorfly-e708-q1.dts.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The presence of the mma8452_int_e708_q1 node is a copy and paste
error, remove it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.

Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.

Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.

This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

As an added bonus this also enables full otg support. I've tested that
this works as advertised.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>