pinctrl fixes for v3.3

* tag 'pinctrl-for-torvalds-20120216' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: restore pin naming

Here are a few more fixes for powerpc.  Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.

Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.

Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point.  For now let's just avoid
building it by default.  Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
  powerpc/adb: Use set_current_state()
  powerpc: Disable interrupts early in Program Check
  powerpc: Remove legacy iSeries from ppc64_defconfig
  powerpc/fsl/pci: Fix PCIe fixup regression
  powerpc: Fix kernel log of oops/panic instruction dump

One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI: Fix pci cardbus removal
  PCI: set pci sriov page size before reading SRIOV BAR
  PCI: workaround hard-wired bus number V2

3 radeon fixes, I have some exynos fixes to push later but I'll queue
them separately once I've looked them over a bit.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix MSI re-arm on rv370+
  drm/radeon/kms/atom: bios scratch reg handling updates
  drm/radeon/kms: drop lock in return path of radeon_fence_count_emitted.

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: sha512 - use standard ror64()

After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870e ("i387:
do not preload FPU state at task switch time").

However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably

 - properly abstracted as a true FPU state switch, rather than as
   open-coded save and restore with various hacks.

   In particular, implementing it as a proper FPU state switch allows us
   to optimize the CR0.TS flag accesses: there is no reason to set the
   TS bit only to then almost immediately clear it again.  CR0 accesses
   are quite slow and expensive, don't flip the bit back and forth for
   no good reason.

 - Make sure that the same model works for both x86-32 and x86-64, so
   that there are no gratuitous differences between the two due to the
   way they save and restore segment state differently due to
   architectural differences that really don't matter to the FPU state.

 - Avoid exposing the "preload" state to the context switch routines,
   and in particular allow the concept of lazy state restore: if nothing
   else has used the FPU in the meantime, and the process is still on
   the same CPU, we can avoid restoring state from memory entirely, just
   re-expose the state that is still in the FPU unit.

   That optimized lazy restore isn't actually implemented here, but the
   infrastructure is set up for it.  Of course, older CPU's that use
   'fnsave' to save the state cannot take advantage of this, since the
   state saving also trashes the state.

In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage.  Hopefully it's easier to
follow as a result.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.

This fixes two independent bugs at the same time:

 - changing 'thread_info->status' from the scheduler causes nasty
   problems for the other users of that variable, since it is defined to
   be thread-synchronous (that's what the "TS_" part of the naming was
   supposed to indicate).

   So perfectly valid code could (and did) do

	ti->status |= TS_RESTORE_SIGMASK;

   and the compiler was free to do that as separate load, or and store
   instructions.  Which can cause problems with preemption, since a task
   switch could happen in between, and change the TS_USEDFPU bit. The
   change to TS_USEDFPU would be overwritten by the final store.

   In practice, this seldom happened, though, because the 'status' field
   was seldom used more than once, so gcc would generally tend to
   generate code that used a read-modify-write instruction and thus
   happened to avoid this problem - RMW instructions are naturally low
   fat and preemption-safe.

 - On x86-32, the current_thread_info() pointer would, during interrupts
   and softirqs, point to a *copy* of the real thread_info, because
   x86-32 uses %esp to calculate the thread_info address, and thus the
   separate irq (and softirq) stacks would cause these kinds of odd
   thread_info copy aliases.

   This is normally not a problem, since interrupts aren't supposed to
   look at thread information anyway (what thread is running at
   interrupt time really isn't very well-defined), but it confused the
   heck out of irq_fpu_usable() and the code that tried to squirrel
   away the FPU state.

   (It also caused untold confusion for us poor kernel developers).

It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling).  And the FPU data that we are going to save/restore is
found there too.

Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.

Cc: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: NRaphael Prevost <raphael@buro.asia>
Acked-and-tested-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Tested-by: NPeter Anvin <hpa@zytor.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending.  In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state.  That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.

We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it

 (a) corrupts what is potentially perfectly good FPU state that we might
     want to lazy avoid restoring later and

 (b) on x86-64 it resulted in a very annoying ordering constraint, where
     "__unlazy_fpu()" in the task switch needs to be delayed until after
     the DS segment has been reloaded just to get the new DS value.

Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used).  It's
simply a much more natural place for the leaked state cleanup.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code.  And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.

Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better.  If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.

In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has.  For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.

In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those.  That means that we have
fewer random places that open-code this situation.

The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.

Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it.  By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5b1cbac3 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.

However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.

Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.

This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid.  With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.

There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.

However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.

Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.

Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

perf on POWER stopped working after commit e050e3f0 (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.

Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.

With the patch applied I get the expected number of samples:

          SAMPLE events:       9948
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>

Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.

We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.

This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().

However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Since we are heading towards removing the Legacy iSeries platform, start
by no longer building it for ppc64_defconfig.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.

We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.

The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.

To fix this, the KERN_CONT log level is added before the actual text of
the printed message.

=== Before the patch ===

[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500]  4e800020 3803ffd0 2b800009

<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500]  4e800020 3803ffd0 2b800009

=== After the patch ===

[   51.385216] Instruction dump:
[   51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[   51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009

<4>[   51.385216] Instruction dump:
<4>[   51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[   51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use standard ror64() instead of hand-written.
There is no standard ror64, so create it.

The difference is shift value being "unsigned int" instead of uint64_t
(for which there is no reason). gcc starts to emit native ROR instructions
which it doesn't do for some reason currently. This should make the code
faster.

Patch survives in-tree crypto test and ping flood with hmac(sha512) on.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The check for save_init_fpu() (introduced in commit 5b1cbac3: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.

So if anybody did enable them, they'd get one spurious warning.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

One small bug fix from Axel plus a fix for a build failure in unrealistic
but commonly built configs which for some reason manage to survive for
an awfully long time in -next without any reports.

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Fix getting voltage in max8649_enable_time()
  regulator: Fix mc13xxx regulator modular build (again)

Quoth BenH:
 "Here are a few powerpc fixes for 3.3, all pretty trivial.  I also
  added the patch to define GET_IP/SET_IP so we can use some more
  asm-generic goodness."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/pseries/eeh: Fix crash when error happens during device probe
  powerpc/pseries: Fix partition migration hang in stop_topology_update
  powerpc/powernv: Disable interrupts while taking phb->lock
  powerpc: Fix WARN_ON in decrementer_check_overflow
  powerpc/wsp: Fix IRQ affinity setting
  powerpc: Implement GET_IP/SET_IP
  powerpc/wsp: Permanently enable PCI class code workaround

MMC fixes for 3.3-rc4:
 * The most visible fix here is against a regression introduced in 3.3-rc1
   that ran cards in Ultra High Speed mode even when they failed to initialize
   in that mode, leading to lower-speed cards failing to mount.
 * A lockdep warning introduced in 3.3-rc1 is fixed.
 * Various other small driver fixes, most notably for a NULL dereference
   when using highmem with dw_mmc.

* tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: dw_mmc: Fix PIO mode with support of highmem
  mmc: atmel-mci: save and restore sdioirq when soft reset is performed
  mmc: block: Init ro_lock sysfs attr to fix lockdep warnings
  mmc: sh_mmcif: fix late delayed work initialisation
  mmc: tmio_mmc: fix card eject during IO with DMA
  mmc: core: Fix comparison issue in mmc_compare_ext_csds
  mmc: core: Fix PowerOff Notify suspend/resume
  mmc: sdhci-pci: set Medfield SDIO as non-removable
  mmc: core: add the capability for broken voltage
  mmc: core: Fix low speed mmc card detection failure
  mmc: esdhc: set the timeout to the max value
  mmc: esdhc: add PIO mode support
  mmc: core: Ensure clocks are always enabled before host interaction
  mmc: of_mmc_spi: fix little endian support
  mmc: core: UHS sdio card that fails should not exceed 50MHz
  mmc: esdhc: fix errors when booting kernel on Freescale eSDHC version 2.3

Merge tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xenbus_dev: add missing error check to watch handling
  xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
  xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
  xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
  xen/bootup: During bootup suppress XENBUS: Unable to read cpu state

sound fixes for 3.3-rc4

Basically all small fixes suited as rc4: a few HD-audio regression fixes,
a stable fix for an old Dell laptop with intel8x0, and a simple fix for
ASoC fsi.

* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: intel8x0: Fix default inaudible sound on Gateway M520
  ALSA: hda - Fix silent speaker output on Acer Aspire 6935
  ALSA: hda - Fix initialization of secondary capture source on VT1705
  ASoC: fsi: fixup fsi_pointer() calculation method
  ALSA: hda - Fix mute-LED VREF value for new HP laptops

MSI_REARM_EN register is a write only trigger register.
There is no need RMW when re-arming.

May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=41668Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Add missing DFP6 connection state handling
- crtc routing bits not used on DCE4+

Noticed by sylware on phoronix.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Silly bad return path.

Reported-and-Tested-by: Mikko Vinni
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

BugLink: https://bugs.launchpad.net/bugs/930842

The reporter states that audio is inaudible by default without muting
'External Amplifier'. Add a quirk to handle his SSID so that changing
the control is not necessary.
Reported-and-tested-by: NBenjamin Carlson <elderbubba0810@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A simple fix from Morimoto-san for the pointer() operation in the FSI
driver.

* git://git.samba.org/sfrench/cifs-2.6:
  cifs: don't return error from standard_receive3 after marking response malformed
  cifs: request oplock when doing open on lookup
  cifs: fix error handling when cifscreds key payload is an error

This updates the sha512 fix so that it doesn't cause excessive stack
usage on i386.  This is done by reverting to the original code, and
avoiding the W duplication by moving its initialisation into the loop.

As the underlying code is in fact the one that we have used for years,
I'm pushing this now instead of postponing to the next cycle.

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: sha512 - Avoid stack bloat on i386
  crypto: sha512 - Use binary and instead of modulus

EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.

Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This fixes a hang that was observed during live partition migration.
Since stop_topology_update must not be called from an interrupt
context, call it earlier in the migration process. The hang observed
can be seen below:

WARNING: at kernel/timer.c:1011
Modules linked in: ip6t_LOG xt_tcpudp xt_pkttype ipt_LOG xt_limit ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_raw xt_NOTRACK ipt_REJECT xt_state iptable_raw iptable_filter ip6table_mangle nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables ip6table_filter ip6_tables x_tables ipv6 fuse loop ibmveth sg ext3 jbd mbcache raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid10 raid1 raid0 scsi_dh_alua scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc dm_round_robin dm_multipath scsi_dh sd_mod crc_t10dif ibmvfc scsi_transport_fc scsi_tgt scsi_mod dm_snapshot dm_mod
NIP: c0000000000c52d8 LR: c00000000004be28 CTR: 0000000000000000
REGS: c00000005ffd77d0 TRAP: 0700   Not tainted  (3.2.0-git-00001-g07d106d0)
MSR: 8000000000021032 <ME,CE,IR,DR>  CR: 48000084  XER: 00000001
CFAR: c00000000004be20
TASK = c00000005ec78860[0] 'swapper/3' THREAD: c00000005ec98000 CPU: 3
GPR00: 0000000000000001 c00000005ffd7a50 c000000000fbbc98 c000000000ec8340
GPR04: 00000000282a0020 0000000000000000 0000000000004000 0000000000000101
GPR08: 0000000000000012 c00000005ffd4000 0000000000000020 c000000000f3ba88
GPR12: 0000000000000000 c000000007f40900 0000000000000001 0000000000000004
GPR16: 0000000000000001 0000000000000000 0000000000000000 c000000001022310
GPR20: 0000000000000001 0000000000000000 0000000000200200 c000000001029e14
GPR24: 0000000000000000 0000000000000001 0000000000000040 c00000003f74bc80
GPR28: c00000003f74bc84 c000000000f38038 c000000000f16b58 c000000000ec8340
NIP [c0000000000c52d8] .del_timer_sync+0x28/0x60
LR [c00000000004be28] .stop_topology_update+0x20/0x38
Call Trace:
[c00000005ffd7a50] [c00000005ec78860] 0xc00000005ec78860 (unreliable)
[c00000005ffd7ad0] [c00000000004be28] .stop_topology_update+0x20/0x38
[c00000005ffd7b40] [c000000000028378] .__rtas_suspend_last_cpu+0x58/0x260
[c00000005ffd7bf0] [c0000000000fa230] .generic_smp_call_function_interrupt+0x160/0x358
[c00000005ffd7cf0] [c000000000036ec8] .smp_ipi_demux+0x88/0x100
[c00000005ffd7d80] [c00000000005c154] .icp_hv_ipi_action+0x5c/0x80
[c00000005ffd7e00] [c00000000012a088] .handle_irq_event_percpu+0x100/0x318
[c00000005ffd7f00] [c00000000012e774] .handle_percpu_irq+0x84/0xd0
[c00000005ffd7f90] [c000000000022ba8] .call_handle_irq+0x1c/0x2c
[c00000005ec9ba20] [c00000000001157c] .do_IRQ+0x22c/0x2a8
[c00000005ec9bae0] [c0000000000054bc] hardware_interrupt_entry+0x18/0x1c
Exception: 501 at .cpu_idle+0x194/0x2f8
    LR = .cpu_idle+0x194/0x2f8
[c00000005ec9bdd0] [c000000000017e58] .cpu_idle+0x188/0x2f8 (unreliable)
[c00000005ec9be90] [c00000000067ec18] .start_secondary+0x3e4/0x524
[c00000005ec9bf90] [c0000000000093e8] .start_secondary_prolog+0x10/0x14
Instruction dump:
ebe1fff8 4e800020 fbe1fff8 7c0802a6 f8010010 7c7f1b78 f821ff81 78290464
80090014 5400019e 7c0000d0 78000fe0 <0b000000> 4800000c 7c210b78 7c421378
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to disable interrupts when taking the phb->lock. Otherwise
we could deadlock with pci_lock taken from an interrupt.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We call the cache_hwirq_map() function with a linux IRQ number
but it expects a HW irq number. This triggers a BUG on multic-chip
setups in addition to not doing the right thing.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With this change, helpers such as instruction_pointer() et al, get defined
in the generic header in terms of GET_IP

Removed the unnecessary definition of profile_pc in !CONFIG_SMP case as
suggested by Mike Frysinger.
Signed-off-by: NSrikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It appears that on the Chroma card, the class code of the root
complex is still wrong even on DD2 or later chips. This could
be a firmware issue, but that breaks resource allocation so let's
unconditionally fix it up.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Current PIO mode makes a kernel crash with CONFIG_HIGHMEM.
Highmem pages have a NULL from sg_virt(sg).
This patch fixes the following problem.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0    Not tainted  (3.0.15-01423-gdbf465f #589)
PC is at dw_mci_pull_data32+0x4c/0x9c
LR is at dw_mci_read_data_pio+0x54/0x1f0
pc : [<c0358824>]    lr : [<c035988c>]    psr: 20000193
sp : c0619d48  ip : c0619d70  fp : c0619d6c
r10: 00000000  r9 : 00000002  r8 : 00001000
r7 : 00000200  r6 : 00000000  r5 : e1dd3100  r4 : 00000000
r3 : 65622023  r2 : 0000007f  r1 : eeb96000  r0 : e1dd3100
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment
xkernel
Control: 10c5387d  Table: 61e2004a  DAC: 00000015
Process swapper (pid: 0, stack limit = 0xc06182f0)
Stack: (0xc0619d48 to 0xc061a000)
9d40:                   e1dd3100 e1a4f000 00000000 e1dd3100 e1a4f000 00000200
9d60: c0619da4 c0619d70 c035988c c03587e4 c0619d9c e18158f4 e1dd3100 e1dd3100
9d80: 00000020 00000000 00000000 00000020 c06e8a84 00000000 c0619e04 c0619da8
9da0: c0359b24 c0359844 e18158f4 e1dd3164 e1dd3168 e1dd3150 3d02fc79 e1dd3154
9dc0: e1dd3178 00000000 00000020 00000000 e1dd3150 00000000 c10dd7e8 e1a84900
9de0: c061e7cc 00000000 00000000 0000008d c06e8a84 c061e780 c0619e4c c0619e08
9e00: c00c4738 c0359a34 3d02fc79 00000000 c0619e4c c05a1698 c05a1670 c05a165c
9e20: c04de8b0 c061e780 c061e7cc e1a84900 ffffed68 0000008d c0618000 00000000
9e40: c0619e6c c0619e50 c00c48b4 c00c46c8 c061e780 c00423ac c061e7cc ffffed68
9e60: c0619e8c c0619e70 c00c7358 c00c487c 0000008d ffffee38 c0618000 ffffed68
9e80: c0619ea4 c0619e90 c00c4258 c00c72b0 c00423ac ffffee38 c0619ecc c0619ea8
9ea0: c004241c c00c4234 ffffffff f8810000 0000006d 00000002 00000001 7fffffff
9ec0: c0619f44 c0619ed0 c0048bc0 c00423c4 220ae7a9 00000000 386f0d30 0005d3a4
9ee0: c00423ac c10dd0b8 c06f2cd8 c0618000 c0594778 c003a674 7fffffff c0619f44
9f00: 386f0d30 c0619f18 c00a6f94 c005be3c 80000013 ffffffff 386f0d30 0005d3a4
9f20: 386f0d30 0005d2d1 c10dd0a8 c10dd0b8 c06f2cd8 c0618000 c0619f74 c0619f48
9f40: c0345858 c005be00 c00a2440 c0618000 c0618000 c00410d8 c06c1944 c00410fc
9f60: c0594778 c003a674 c0619f9c c0619f78 c004a7e8 c03457b4 c0618000 c06c18f8
9f80: 00000000 c0039c70 c06c18d4 c003a674 c0619fb4 c0619fa0 c04ceafc c004a714
9fa0: c06287b4 c06c18f8 c0619ff4 c0619fb8 c0008b68 c04cea68 c0008578 00000000
9fc0: 00000000 c003a674 00000000 10c5387d c0628658 c003aa78 c062f1c4 4000406a
9fe0: 413fc090 00000000 00000000 c0619ff8 40008044 c0008858 00000000 00000000
Backtrace:
[<c03587d8>] (dw_mci_pull_data32+0x0/0x9c) from [<c035988c>] (dw_mci_read_data_pio+0x54/0x1f0)
 r6:00000200 r5:e1a4f000 r4:e1dd3100
 [<c0359838>] (dw_mci_read_data_pio+0x0/0x1f0) from [<c0359b24>] (dw_mci_interrupt+0xfc/0x4a4)
[<c0359a28>] (dw_mci_interrupt+0x0/0x4a4) from [<c00c4738>] (handle_irq_event_percpu+0x7c/0x1b4)
[<c00c46bc>] (handle_irq_event_percpu+0x0/0x1b4) from [<c00c48b4>] (handle_irq_event+0x44/0x64)
[<c00c4870>] (handle_irq_event+0x0/0x64) from [<c00c7358>] (handle_fasteoi_irq+0xb4/0x124)
 r7:ffffed68 r6:c061e7cc r5:c00423ac r4:c061e780
 [<c00c72a4>] (handle_fasteoi_irq+0x0/0x124) from [<c00c4258>] (generic_handle_irq+0x30/0x38)
 r7:ffffed68 r6:c0618000 r5:ffffee38 r4:0000008d
 [<c00c4228>] (generic_handle_irq+0x0/0x38) from [<c004241c>] (asm_do_IRQ+0x64/0xe0)
 r5:ffffee38 r4:c00423ac
 [<c00423b8>] (asm_do_IRQ+0x0/0xe0) from [<c0048bc0>] (__irq_svc+0x80/0x14c)
Exception stack(0xc0619ed0 to 0xc0619f18)
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>