We don't actually check for INTEL_OUTPUT_DP_MST at all in here, as a
result we skip assigning a DPLL to any DP MST ports, which makes link
training fail:

[ 1442.933896] [drm:intel_power_well_enable] enabling DDI D power well
[ 1442.933905] [drm:skl_set_power_well] Enabling DDI D power well
[ 1442.933957] [drm:intel_mst_pre_enable_dp] 0
[ 1442.935474] [drm:intel_dp_set_signal_levels] Using signal levels 00000000
[ 1442.935477] [drm:intel_dp_set_signal_levels] Using vswing level 0
[ 1442.935480] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0
[ 1442.936190] [drm:intel_dp_set_signal_levels] Using signal levels 05000000
[ 1442.936193] [drm:intel_dp_set_signal_levels] Using vswing level 1
[ 1442.936195] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 1
[ 1442.936858] [drm:intel_dp_set_signal_levels] Using signal levels 08000000
[ 1442.936862] [drm:intel_dp_set_signal_levels] Using vswing level 2
…
[ 1442.998253] [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* too many full retries, give up
[ 1442.998512] [drm:intel_dp_start_link_train [i915]] *ERROR* failed to train DP, aborting

After which the pipe state goes completely out of sync:

[   70.075596] [drm:check_crtc_state] [CRTC:25]
[   70.075696] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in ddi_pll_sel (expected 0x00000000, found 0x00000001)
[   70.075747] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in shared_dpll (expected -1, found 0)
[   70.075798] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000021)
[   70.075840] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x80400173)
[   70.075884] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr2 (expected 0x00000000, found 0x000003a5)
[   70.075954] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 262750, found 72256)
[   70.075999] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 540000, found 148500)

And if you're especially lucky, it keeps going downhill:

[   83.309256] Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler
[   83.309265]
[   83.309265] =================================
[   83.309266] [ INFO: inconsistent lock state ]
[   83.309267] 4.5.0-rc1Lyude-Test #265 Not tainted
[   83.309267] ---------------------------------
[   83.309268] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[   83.309270] Xorg/1194 [HC0[1]:SC0[0]:HE1:SE1] takes:
[   83.309293]  (&(&dev_priv->uncore.lock)->rlock){?.-...}, at: [<ffffffffa02a6073>] gen9_write32+0x63/0x400 [i915]
[   83.309293] {IN-HARDIRQ-W} state was registered at:
[   83.309297]   [<ffffffff810e84f4>] __lock_acquire+0x9c4/0x1d00
[   83.309299]   [<ffffffff810ea1be>] lock_acquire+0xce/0x1c0
[   83.309302]   [<ffffffff8177d936>] _raw_spin_lock_irqsave+0x56/0x90
[   83.309321]   [<ffffffffa02a5492>] gen9_read32+0x52/0x3d0 [i915]
[   83.309332]   [<ffffffffa024beea>] gen8_irq_handler+0x27a/0x6a0 [i915]
[   83.309337]   [<ffffffff810fdbc1>] handle_irq_event_percpu+0x41/0x300
[   83.309339]   [<ffffffff810fdeb9>] handle_irq_event+0x39/0x60
[   83.309341]   [<ffffffff811010b4>] handle_edge_irq+0x74/0x130
[   83.309344]   [<ffffffff81009073>] handle_irq+0x73/0x120
[   83.309346]   [<ffffffff817805f1>] do_IRQ+0x61/0x120
[   83.309348]   [<ffffffff8177e6d6>] ret_from_intr+0x0/0x20
[   83.309351]   [<ffffffff815f5105>] cpuidle_enter_state+0x105/0x330
[   83.309353]   [<ffffffff815f5367>] cpuidle_enter+0x17/0x20
[   83.309356]   [<ffffffff810dbe1a>] call_cpuidle+0x2a/0x50
[   83.309358]   [<ffffffff810dc1dd>] cpu_startup_entry+0x26d/0x3a0
[   83.309360]   [<ffffffff817701da>] rest_init+0x13a/0x140
[   83.309363]   [<ffffffff81f2af8e>] start_kernel+0x475/0x482
[   83.309365]   [<ffffffff81f2a315>] x86_64_start_reservations+0x2a/0x2c
[   83.309367]   [<ffffffff81f2a452>] x86_64_start_kernel+0x13b/0x14a

Fixes: 82d35437 ("drm/i915/skl: Implementation of SKL DPLL programming")
Signed-off-by: NLyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454428183-994-1-git-send-email-cpaul@redhat.com

Used by production devices:
    Intel(R) Iris Graphics 540 (Skylake GT3e)
    Intel(R) Iris Graphics 550 (Skylake GT3e)

v2: More ids
v3: Less ids (GT1 got duplicated)

Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454674902-26207-1-git-send-email-michal.winiarski@intel.com

It's safe to assume cxsr is already disabled when the crtc is off.
This prevents an unclaimed register warning when the required power
wells are not enabled.

[  262.864984] ------------[ cut here ]------------
[  262.865025] WARNING: CPU: 1 PID: 6799 at drivers/gpu/drm/i915/intel_uncore.c:638 __unclaimed_reg_debug+0x68/0x80 [i915]()
[  262.865029] Unclaimed register detected before reading register 0x186500
[  262.865032] Modules linked in: i915 intel_powerclamp
[  262.865057] CPU: 1 PID: 6799 Comm: kms_pipe_crc_ba Tainted: G     U  W       4.4.0-gfxbench+ #1
[  262.865060] Hardware name: DN2820FYK, BIOS FYBYT10H.86A.0038.2014.0717.1455 07/17/2014
[  262.865064]  ffffffffa0338cf8 ffff88007448ba78 ffffffff813df90c ffff88007448bac0
[  262.865071]  ffff88007448bab0 ffffffff810746e1 0000000000186500 0000000000000001
[  262.865077]  0000000000000001 ffff880074420000 0000000000000000 ffff88007448bb10
[  262.865083] Call Trace:
[  262.865092]  [<ffffffff813df90c>] dump_stack+0x4e/0x82
[  262.865098]  [<ffffffff810746e1>] warn_slowpath_common+0x81/0xc0
[  262.865102]  [<ffffffff81074767>] warn_slowpath_fmt+0x47/0x50
[  262.865128]  [<ffffffffa02a07e8>] __unclaimed_reg_debug+0x68/0x80 [i915]
[  262.865154]  [<ffffffffa02a0e4e>] vlv_read32+0x2de/0x370 [i915]
[  262.865173]  [<ffffffffa0256837>] intel_set_memory_cxsr+0x87/0x1a0 [i915]
[  262.865200]  [<ffffffffa02c4cb3>] intel_pre_plane_update+0xb3/0xf0 [i915]
[  262.865228]  [<ffffffffa02c54b5>] intel_atomic_commit+0x3b5/0x17c0 [i915]
[  262.865234]  [<ffffffff8150dc45>] ? drm_atomic_check_only+0x145/0x660
[  262.865239]  [<ffffffff8150d75a>] ? drm_atomic_set_crtc_for_connector+0x6a/0xe0
[  262.865243]  [<ffffffff8150e192>] drm_atomic_commit+0x32/0x50
[  262.865249]  [<ffffffff814eb155>] drm_atomic_helper_set_config+0x75/0xb0
[  262.865253]  [<ffffffff814fd090>] drm_mode_set_config_internal+0x60/0x110
[  262.865258]  [<ffffffff81501e26>] drm_mode_setcrtc+0x186/0x4f0
[  262.865263]  [<ffffffff814f3eed>] drm_ioctl+0x13d/0x590
[  262.865267]  [<ffffffff81501ca0>] ? drm_mode_setplane+0x1b0/0x1b0
[  262.865273]  [<ffffffff811d4c4c>] do_vfs_ioctl+0x2fc/0x550
[  262.865278]  [<ffffffff8118d5ea>] ? vm_munmap+0x4a/0x60
[  262.865283]  [<ffffffff811e06ba>] ? __fget_light+0x6a/0x90
[  262.865287]  [<ffffffff811d4edc>] SyS_ioctl+0x3c/0x70
[  262.865292]  [<ffffffff8179a75b>] entry_SYSCALL_64_fastpath+0x16/0x73
[  262.865296] ---[ end trace 6387a0ad001bb39f ]---

Testcase: kms_flip.basic-flip-vs-wf_vblank
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93698Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454514805-10595-4-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

This can be derived from the atomic state in pre_plane_update,
which makes it more clear when it's supposed to be called.
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454514805-10595-3-git-send-email-maarten.lankhorst@linux.intel.com

This is a revert of commit 066cf55b "drm/i915: Fix IPS related flicker".
intel_pre_disable_primary already handles this, and now everything
goes through the atomic path there's no need to try to disable ips twice.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454514805-10595-2-git-send-email-maarten.lankhorst@linux.intel.com

RC6 setup is shared between BIOS and Driver. BIOS sets up subset of RC6
setup registers. If those are not setup Driver should not enable RC6.
For implementing this, driver can check RC_CTRL0 and RC_CTRL1 values
to know if BIOS has enabled HW/SW RC6.
This will also enable user to control RC6 using BIOS settings alone.
RC6 related instability can be avoided by disabling via BIOS settings
till driver fixes it.

v2: Had placed logic in gen8 function by mistake. Fixed it.
Ensuring RPM is not enabled in case BIOS disabled RC6.

v3: Need to disable RPM if RC6 is disabled due to BIOS settings. (Daniel)
Runtime PM enabling happens before gen9_enable_rc6.
Moved the updation of enable_rc6 parameter in intel_uncore_sanitize.

v4: Added elaborate check for BIOS RC6 setup. Prepared check_pctx for bxt.
    (Imre)

v5: Caching reserved stolen base and size in the driver private data.
    Reorganized RC6 setup check. Moved from gen9_enable_rc6 to
    intel_uncore_sanitize. (Imre)

v6: Rebasing on the patch submitted by Imre that moves gem_init_stolen
    earlier in the load.

v7: Removed PWRCTX_MAXCNT_VCSUNIT1 check as it applies to SKL. (Imre)

v8: Fixed formatting and checkpatch issues. Fixed functional issue where
    RC6 ctx size check was missing. (Imre)

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454697809-22113-1-git-send-email-sagar.a.kamble@intel.com

Per spec, TPS3 support is mandatory for downstream devices that support
HBR2. We've therefore logged errors on HBR2 without TPS3 since

commit 1da7d713
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Thu Sep 3 11:16:08 2015 +0300

    drm/i915: ignore link rate in TPS3 selection

However, it seems there are real world devices out there that just
aren't spec compliant, and still work at HBR2 using TPS2. So reduce the
error message to debug logging.

Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92932
Fixes: 1da7d713 ("drm/i915: ignore link rate in TPS3 selection")
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454667370-8001-2-git-send-email-jani.nikula@intel.com

Make it cleaner to add more checks in the function. No functional
changes.

Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org # dependency on the next patch
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454667370-8001-1-git-send-email-jani.nikula@intel.com

Skip v3 gpio element because the support is not there, and skip gpio
element on non-vlv because the sideband code is vlv specific.

v2: the gpio stuff is currently only supported on vlv (Ville)

Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 2a33d934 ("drm/i915/bios: add support for MIPI sequence block v3")
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454604767-2440-1-git-send-email-jani.nikula@intel.com

Make the gpio read/write functions more generic iosf sideband read/write
functions, taking the iosf port as argument.

v2: rebase
v3: rebase
v4 by Jani: address Ville's review
v5 by Jani: drop the PCI_DEVFN change (Ville)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454604915-17142-1-git-send-email-jani.nikula@intel.com

Not needed.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/532150999335216b1374c606e1b3c253a6c9fe9d.1454582914.git.jani.nikula@intel.com

Make it easier to spot duplicates.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/a89f10d2d1954ac1b9a278534cb5209973354caa.1454582914.git.jani.nikula@intel.com

Since sequence block v2 the second byte contains flags other than just
pull up/down. Don't pass arbitrary data to the sideband interface.

The rest may or may not work for sequence block v2, but there should be
no harm done.

Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/ebe3c2eee623afc4b3a134533b01f8d591d13f32.1454582914.git.jani.nikula@intel.com

Do not blindly trust the VBT data used for indexing.

Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/cc32d40c2b47f2d2151811855ac2c3dabab1d57d.1454582914.git.jani.nikula@intel.com

Now that we have top-level gen-independent hw_activate and
hw_deactivate functions, set fbc->active directly from them, removing
the duplicated code.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454101060-23198-3-git-send-email-paulo.r.zanoni@intel.com

The recent introduction of a new caller of dev_priv->fbc.deactivate()
is a good example of why we need unexport those functions. Anything
outside intel_fbc.c should only call the functions exported by
intel_fbc.c, so in order to enforce that, kill the function pointers
stored inside dev_priv->fbc and replace them with functions that can't
be called from outside intel_fbc.c.

This should make it much harder for new code to call these functions
from outside intel_fbc.c.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454101060-23198-2-git-send-email-paulo.r.zanoni@intel.com

FBC is already deactivated at this point.

Besides, nothing should be calling these lower-level function
pointers. A few months ago, the only caller of
dev_priv->fbc.deactivate was intel_pipe_set_base_atomic(), which was
the kgdboc function. But the following commit added it to the SKL
function:

    commit a8d201af
    Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
    Date:   Thu Jan 7 11:54:11 2016 +0100
        drm/i915: Use plane state for primary plane updates.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454101060-23198-1-git-send-email-paulo.r.zanoni@intel.com

WaIncreaseDefaultTLBEntries increases the number of TLB
entries available for GPGPU workloads and gives significant
( > 10% ) performance gain for some OCL benchmarks.
Put this in a new function that can be a place for
workarounds that are GT related but not required per ring.
This function is called on driver load and also after a
reset and on resume, so it is safe for workarounds that get
clobbered in these situations. This function currently has
just this one workaround.

v2: This was originally split into 3 patches but following
  review feedback was squashed into 1.
  I have not incorporated some style comments from Chris
  Wilson as I felt that after defining and intialising a
  temporary variable and then adding an additional if block
  to only write the register if the temporary variable had
  been set, this didn't really give a net gain.

v3: Resending in the hope that BAT will run

v4: Change subject line to trigger BAT (please!)
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454586574-2343-1-git-send-email-tim.gore@intel.com

We need to enable DSI PLL before configuring the DSI registers.

This has worked before on BYT/CHV, but BXT is more fussy.
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Tested-by: Mika Kahola <mika.kahola@intel.com> # BXT
Tested-by: Jani Nikula <jani.nikula@intel.com> # BYT
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454503846-12103-1-git-send-email-ramalingam.c@intel.com

commit 033908ae
Author: Dave Gordon <david.s.gordon@intel.com>
Date:   Thu Dec 10 18:51:23 2015 +0000

    drm/i915: mark GEM object pages dirty when mapped & written by the CPU

introduced a check into i915_gem_object_get_dirty_pages() that returned
a NULL pointer when called with a bad object, one that was not backed by
shmemfs. This WARN was too strict as we can work on all struct page
backed objects, and resulted in a WARN + GPF for existing userspace. In
order to differentiate the various types of objects, add a new flags field
to the i915_gem_object_ops struct to describe their capabilities, with
the first flag being whether the object has struct pages.

v2: Drop silly const before an integer in the structure declaration.

Testcase: igt/gem_userptr_blits/relocations
Reported-and-tested-by: NKristian Høgsberg Kristensen <krh@bitplanet.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Kristian Høgsberg Kristensen <krh@bitplanet.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NKristian Høgsberg Kristensen <krh@bitplanet.net>
Tested-by: NMichal Winiarski <michal.winiarski@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453487551-16799-1-git-send-email-chris@chris-wilson.co.uk

Due to our lack of two-step watermark programming, our driver has
historically pretended that the cursor plane is always on for the
purpose of watermark calculations; this helps avoid serious flickering
when the cursor turns off/on (e.g., when the user moves the mouse
pointer to a different screen).  That workaround was accidentally
dropped as we started working toward atomic watermark updates.  Since we
still aren't quite there yet with two-stage updates, we need to
resurrect the workaround and treat the cursor as always active.

v2: Tweak cursor width calculations slightly to more closely match the
    logic we used before the atomic overhaul began.  (Ville)

Cc: simdev11@outlook.com
Cc: manfred.kitzbichler@gmail.com
Cc: drm-intel-fixes@lists.freedesktop.org
Reported-by: simdev11@outlook.com
Reported-by: manfred.kitzbichler@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93892
Fixes: 43d59eda ("drm/i915: Eliminate usage of plane_wm_parameters from ILK-style WM code (v2)")
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454479611-6804-1-git-send-email-matthew.d.roper@intel.com

In commit bfb9faab8 we added a workaround for some BXT BIOS that fail to
properly initialize the DDI_A_4_LANES bit of the control register (4
lanes is the only valid configuration on BXT since there is no DDI E to
share with).  A recent patch added some additional checks on this
register bit before the workaround gets applied; this breaks eDP on BXT
in some settings.  Some minor code shuffling is all we need to restore
the workaround.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 7cd87cb80 ("drm/i915: Check max number of lanes when registering DDI ports")
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454022577-834-1-git-send-email-matthew.d.roper@intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Our attempts save/restore panel power state in i915_suspend.c are
causing unclaimed register warnings on BXT since the registers for this
platform differ from older platforms.

The big hammer suspend/resume shouldn't be necessary for PP since the
connector/encoder hooks should already handle this.  In theory we could
remove this for all platforms, but in practice it's likely that would
cause some regressions since older platforms with LVDS may have
incomplete PP handling.  For now we'll leave the PCH save/restore alone
and change the non-PCH branch to only operate on gen <= 4 so that BXT
and future platforms aren't included.

v2: Typo fix: s/||/&&/

v3: Change non-PCH condition to a gen <= 4 test rather than listing
    VLV/CHV/BXT as specific platforms to exclude; should be more
    future-proof as we add new platforms.  (Daniel)

Cc: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452102821-17190-1-git-send-email-matthew.d.roper@intel.com

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454071949-24677-4-git-send-email-imre.deak@intel.com

While not being able to enable MSI interrupts may be a normal
circumstance, for debugging it may still be a useful information, so
emit an info about this.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454071949-24677-3-git-send-email-imre.deak@intel.com

Atm we wouldn't catch these errors or on the error path we would end up
with a division-by-zero, fix this up.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454071949-24677-2-git-send-email-imre.deak@intel.com

While we are calling intel_dp_aux_transfer() with msg->size=0 whenever
msg->buffer is NULL, passing NULL to memcpy() is undefined according to
the ISO C standard. I haven't found any notes about this in the GNU C's
or the kernel's documentation of the function and can't imagine what it
would do with the NULL ptr. To better document this use of the
parameters it still make sense to add an explicit check for this to the
code.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454071949-24677-1-git-send-email-imre.deak@intel.com

Add PCIIDs for new versions of the SOC, based on BSpec. Also add the
name of the versions as code comment where this is available. The new
versions don't have any changes visible to the kernel driver.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453989852-13569-1-git-send-email-imre.deak@intel.com

On SKL and KBL we can have pipe A/B/C disabled by fuse settings. The
pipes must be fused in descending order (e.g. C, B+C, A+B+C). We simply
decrease info->num_pipes if we find a valid fused out config.

v2: Don't store the pipe disabled mask in device info (Damien)

v3: Don't check FUSE_STRAP register for pipe c disabled

Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[Jani: fixed some checkpatch indentation complaints]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453300280-10661-1-git-send-email-patrik.jakobsson@linux.intel.com

Unfortunately we don't know all panels and platforms out there and we
found internal prototypes without VBT proper set but where only
link in standby worked well.

So, before enable PSR by default let's instrument the PSR parameter
in a way that we can identify different panels out there that might
require or work better with link standby mode.

It is also useful to say that for backward compatibility I'm not
changing the meaning of this flag. So "0" still means disabled
and "1" means enabled with full support and maximum power savings.

v2: Use positive value instead of negative for different operation mode
    as suggested by Daniel.

v3: As Paulo suggested use 2 to force link standby and 3 to force link
    fully on. Also split the link_standby introduction in a separated patch.

v4: Use DRM_ERROR for link off request on platforms that don't support and
    Remove the quirk promise.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454356928-19779-1-git-send-email-rodrigo.vivi@intel.com

Link standby support has been deprecated with 'commit 89251b17
("drm/i915: PSR: deprecate link_standby support for core platforms.")'

The reason for that is that main link in full off offers more power
savings and on HSW and BDW implementations on source side had known
bugs with link standby.

However that same HSD report only mentions BDW and HSW and tells that
a fix was going to new platforms. Since on Skylake link standby
didn't cause the bad blank flickering screens seen on HSW and BDW
let's respect VBT again for this and future platforms.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

Current code not just block link_standby for non DDI platforms but also
block PSR from work on other ports B/C/D/E.

So, besides change any behaviour let's just fix the mess a bit here and
reuse HSW check to block the other ports and reduce the second if only to
link stadnby request.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

The driver does not load firmware for unknown steppings, so these new
steppings must be added to the list.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454023163-25469-1-git-send-email-mathew.j.martineau@linux.intel.com

When we stop the sink CRC calculation we wait a while until the counter
is reset to zero and return -ETIMEDOUT. However the sink crc was
calculated already by this point so we just ignore this return at
the main function.

So, let's also ignore the message and put it as a debug message instead
of an error one. The message might still be useful when debuging
test failures so we could be able to know something was not going so
well with sink crc stop.

v2: Improve log message.

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=93694
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454107499-29678-1-git-send-email-rodrigo.vivi@intel.com

The FBC fixes we've been doing in the last months required a lot of
refactor, so functions that were once big and called from different
spots are now small and called only once. IMHO now it's better to just
move the contents of these functions to their only callers since this
reduces the number of indirections while reading the code.

While at it, also improve the related comments a little bit.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-26-git-send-email-paulo.r.zanoni@intel.com

We already make sure we run intel_fbc_update_update during modesets
and page flips, and this function takes care of deactivating FBC, so
it shouldn't be possible for us to reach the condition we check at
intel_fbc_work_fn. So instead of grabbing framebuffer references and
adding a lot of code to track when we need to free them, just don't
track anything at all since we shouldn't need to.

v2: Rebase.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-25-git-send-email-paulo.r.zanoni@intel.com

Make sure we do the pre_update - which also deactivates FBC - before
we actually schedule the page flip, just to make sure we don't
flip to the new FB with FBC still activated for the previous FB.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-24-git-send-email-paulo.r.zanoni@intel.com

We don't actually use fb_id anywhere. We already compare all
parameters that matter to the hardware: pixel format, stride,
fence_reg and ggtt_offset. The ID shouldn't make a difference.

Besides, we already update the FBC data at every modeset/flip, so this
can't change behind our backs.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-23-git-send-email-paulo.r.zanoni@intel.com

Our dmesg messages started being misleading after we converted to the
enable+activate model: we always print "Disabling FBC", even when
we're just deactivating it. So, for example, when I boot my machine
and do "dmesg | grep -i fbc", I see:
  [drm:intel_fbc_enable] Enabling FBC on pipe A
  [drm:set_no_fbc_reason] Disabling FBC: framebuffer not tiled or fenced
but then, if I read the debugfs file, I will see:
  $ sudo cat i915_fbc_status
  FBC enabled
  Compressing: yes
so we can conclude that dmesg is misleading, since FBC is actually
enabled. What happened is that we deactivated FBC due to fbcon not
being tiled, but when we silently reactivated it when the display
manager started. We don't print activation messages since there may be
way too many of these operations per second during normal desktop
usage.

One possible solution would be to change set_no_fbc_reason to
correctly differentiate between disable and deactivation, but we
removed support from printing activation/deactivation messages in the
past because they were too frequent. So instead of doing this, let's
just not print anything on dmesg, and leave the debugfs file if the
user needs to investigate something. We already print when we enable
and disable FBC anyway on a given pipe, so this should already help
triaging bugs.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-22-git-send-email-paulo.r.zanoni@intel.com

During FBC invalidation, don't call intel_fbc_deactivate if it's not
enabled. This doesn't fix any bug, but helps making the interface
saner.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-21-git-send-email-paulo.r.zanoni@intel.com