We need a reserve for allocating buckets for new btree nodes - and now that
we've got multiple btrees, it really needs to be per btree.

This reworks the reserves so we've got separate freelists for each reserve
instead of watermarks, which seems to make things a bit cleaner, and it adds
some code so that btree_split() can make sure the reserve is available before it
starts.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Also flesh out the documentation a bit
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Another minor performance optimization
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Unnecessary since a bucket that has dirty pointers pointing to it can
never be invalidated - and skipping it is a measurable performance
boost, since the bucket gen will usually be a cache miss.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Signed-off-by: NKent Overstreet <kmo@daterainc.com>

We were unnecessarily waiting on a journal write to complete when we just needed
to start a journal write and start setting up the next one.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

The real fix is where we check the bytes we need against how much is
remaining - we also need to check for a journal entry bigger than our
buffer, we'll never write those and it would be bad if we tried to read
one.

Also improve the diagnostic messages.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

The code that handles overlapping extents that we've just read back in from disk
was depending on the behaviour of the code that handles overlapping extents as
we're inserting into a btree node in the case of an insert that forced an
existing extent to be split: on insert, if we had to split we'd also insert a
new extent to represent the top part of the old extent - and then that new
extent would get written out.

The code that read the extents back in thus not bother with splitting extents -
if it saw an extent that ovelapped in the middle of an older extent, it would
trim the old extent to only represent the bottom part, assuming that the
original insert would've inserted a new extent to represent the top part.

I still haven't figured out _how_ it can happen, but I'm now pretty convinced
(and testing has confirmed) that there's some kind of an obscure corner case
(probably involving extent merging, and multiple overwrites in different sets)
that breaks this. The fix is to change the mergesort fixup code to split extents
itself when required.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10

The old writeback PD controller could get into states where it had throttled all
the way down and take way too long to recover - it was too complicated to really
understand what it was doing.

This rewrites a good chunk of it to hopefully be simpler and make more sense,
and it also pays more attention to units which should make the behaviour a bit
easier to understand.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

There is a possibility for a bucket to be invalidated by the allocator
while moving_gc was copying it's contents to another bucket, if the
bucket only held cached data. To prevent this moving checks for
a stale ptr (to an invalidated bucket), before and after reads.
It it finds one, it simply ignores moving that data. This only
affects bcache if the moving_gc was turned on, note that it's
off by default.
Signed-off-by: NNicholas Swenson <nks@daterainc.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Garbage collector needs to check keys in the writeback keybuf to
make sure it's not invalidating buckets to which the writeback
keys point to.
Signed-off-by: NNicholas Swenson <nks@daterainc.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Removed gc_move_threshold because picking buckets only by
threshold could lead moving extra buckets (ei. if there are
buckets at the threshold that aren't supposed to be moved
do to space considerations).

This is replaced by a GC_MOVE bit in the gc_mark bitmask.
Now only marked buckets get moved.
Signed-off-by: NNicholas Swenson <nks@daterainc.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Signed-off-by: NNicholas Swenson <nks@daterainc.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Signed-off-by: NNicholas Swenson <nks@daterainc.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Signed-off-by: NNicholas Swenson <nks@daterainc.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

Dirty data accounting wasn't quite right - firstly, we were adding the key we're
inserting after it could have merged with another dirty key already in the
btree, and secondly we could sometimes pass the wrong offset to
bcache_dev_sectors_dirty_add() for dirty data we were overwriting - which is
important when tracking dirty data by stripe.

NOTE FOR BACKPORTERS: For 3.10 (and 3.11?) there's other accounting fixes
necessary that got squashed in with other patches; the full patch against 3.10
is 408cc2f47eeac93a, available at:
  git://evilpiepirate.org/~kent/linux-bcache.git bcache-3.10-writeback-fixes
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10

diff --git a/drivers/md/bcache/btree.c b/drivers/md/bcache/btree.c
index 2a46036..4a12b2f 100644
--- a/drivers/md/bcache/btree.c
+++ b/drivers/md/bcache/btree.c
@@ -1817,7 +1817,8 @@ static bool fix_overlapping_extents(struct btree *b, struct bkey *insert,
 			if (KEY_START(k) > KEY_START(insert) + sectors_found)
 				goto check_failed;

-			if (KEY_PTRS(replace_key) != KEY_PTRS(k))
+			if (KEY_PTRS(k) != KEY_PTRS(replace_key) ||
+			    KEY_DIRTY(k) != KEY_DIRTY(replace_key))
 				goto check_failed;

 			/* skip past gen */

We're just waiting on kthread_should_stop(), nothing else, so
interruptible sleep was wrong here.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

at the beginning (schedule_timout_interuptible) and others
do his on their own

This prevents wrong load average calculation (load of 1 per thread)
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

An old array block could have its reference count decremented below
zero when it is being replaced in the btree by a new array block.

The fix is to increment the old ablock's reference count just before
inserting a new ablock into the btree.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+

The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit f722063e ("dm space map: optimise
sm_ll_dec and sm_ll_inc").  To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.

Add a DMERR to reflect the potential seriousness of this error.

Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.

With this fix the following dmts regression test now passes:
 dmtest run --suite cache -n /metadata_use_kernel/

The next patch fixes the higher-level dm-array code that exposed this
regression.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+

The module parameter stats_current_allocated_bytes in dm-mod is
read-only.  This parameter informs the user about memory
consumption.  It is not supposed to be changed by the user.

However, despite being read-only, this parameter can be set on
modprobe or insmod command line:
modprobe dm-mod stats_current_allocated_bytes=12345

The kernel doesn't expect that this variable can be non-zero at module
initialization and if the user sets it, it results in warning.

This patch initializes the variable in the module init routine, so
that user-supplied value is ignored.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+

Some module parameters in dm-bufio are read-only. These parameters
inform the user about memory consumption. They are not supposed to be
changed by the user.

However, despite being read-only, these parameters can be set on
modprobe or insmod command line, for example:
modprobe dm-bufio current_allocated_bytes=12345

The kernel doesn't expect that these variables can be non-zero at module
initialization and if the user sets them, it results in BUG.

This patch initializes the variables in the module init routine, so that
user-supplied values are ignored.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.2+

Commit f494a9c6 ("dm cache: cache
shrinking support") broke cache resizing support.

dm_cache_resize() is called with cache->cache_size before it gets
updated to new_size, so it is a no-op.  But the dm-cache superblock is
updated with the new_size even though the backing dm-array is not
resized.  Fix this by passing the new_size to dm_cache_resize().
Signed-off-by: NVincent Pelletier <plr.vincent@gmail.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Micro benchmarks that repeatedly issued IO to a single block were
failing to cause a promotion from the origin device to the cache.  Fix
this by not updating the stats during map() if -EWOULDBLOCK will be
returned.

The mq policy will only update stats, consider migration, etc, once per
tick period (a unit of time established between dm-cache core and the
policies).

When the IO thread calls the policy's map method, if it would like to
migrate the associated block it returns -EWOULDBLOCK, the IO then gets
handed over to a worker thread which handles the migration.  The worker
thread calls map again, to check the migration is still needed (avoids a
race among other things).  *BUT*, before this fix, if we were still in
the same tick period the stats were already updated by the previous map
call -- so the migration would no longer be requested.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

A thin-pool may be in read-only mode because the pool's data or metadata
space was exhausted.  To allow for recovery, by adding more space to the
pool, we must allow a pool to transition from PM_READ_ONLY to PM_WRITE
mode.  Otherwise, running out of space will render the pool permanently
read-only.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

If the thin-pool transitioned to fail mode and the thin-pool's table
were reloaded for some reason: the new table's default pool mode would
be read-write, though it will transition to fail mode during resume.

When the pool mode transitions directly from PM_WRITE to PM_FAIL we need
to re-establish the intermediate read-only state in both the metadata
and persistent-data block manager (as is usually done with the normal
pool mode transition sequence: PM_WRITE -> PM_READ_ONLY -> PM_FAIL).
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Rename commit_or_fallback() to commit().  Now all previous calls to
commit() will trigger the pool mode to fallback if the commit fails.

Also, check the error returned from commit() in alloc_data_block().
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Switch the thin pool to read-only mode in alloc_data_block() if
dm_pool_alloc_data_block() fails because the pool's metadata space is
exhausted.

Differentiate between data and metadata space in messages about no
free space available.

This issue was noticed with the device-mapper-test-suite using:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/

The quantity of errors logged in this case must be reduced.

before patch:

device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
<snip ... these repeat for a _very_ long while ... >
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: commit failed: error = -28
device-mapper: thin: 253:4: switching pool to read-only mode

after patch:

device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: no free metadata space available.
device-mapper: thin: 253:4: switching pool to read-only mode
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org

Switch the thin pool to read-only mode when dm_thin_insert_block() fails
since there is little reason to expect the cause of the failure to be
resolved without further action by user space.

This issue was noticed with the device-mapper-test-suite using:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/

The quantity of errors logged in this case must be reduced.

before patch:

device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: dm_thin_insert_block() failed
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map metadata: unable to allocate new metadata block
<snip ... these repeat for a long while ... >
device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: space map common: dm_tm_shadow_block() failed
device-mapper: thin: 253:4: no free metadata space available.
device-mapper: thin: 253:4: switching pool to read-only mode

after patch:

device-mapper: space map metadata: unable to allocate new metadata block
device-mapper: thin: 253:4: dm_thin_insert_block() failed: error = -28
device-mapper: thin: 253:4: switching pool to read-only mode
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Commit 2fc48021 ("dm persistent
metadata: add space map threshold callback") introduced a regression
to the metadata block allocation path that resulted in errors being
ignored.  This regression was uncovered by running the following
device-mapper-test-suite test:
dmtest run --suite thin-provisioning -n /exhausting_metadata_space_causes_fail_mode/

The ignored error codes in sm_metadata_new_block() could crash the
kernel through use of either the dm-thin or dm-cache targets, e.g.:

device-mapper: thin: 253:4: reached low water mark for metadata device: sending event.
device-mapper: space map metadata: unable to allocate new metadata block
general protection fault: 0000 [#1] SMP
...
Workqueue: dm-thin do_worker [dm_thin_pool]
task: ffff880035ce2ab0 ti: ffff88021a054000 task.ti: ffff88021a054000
RIP: 0010:[<ffffffffa0331385>]  [<ffffffffa0331385>] metadata_ll_load_ie+0x15/0x30 [dm_persistent_data]
RSP: 0018:ffff88021a055a68  EFLAGS: 00010202
RAX: 003fc8243d212ba0 RBX: ffff88021a780070 RCX: ffff88021a055a78
RDX: ffff88021a055a78 RSI: 0040402222a92a80 RDI: ffff88021a780070
RBP: ffff88021a055a68 R08: ffff88021a055ba4 R09: 0000000000000010
R10: 0000000000000000 R11: 00000002a02e1000 R12: ffff88021a055ad4
R13: 0000000000000598 R14: ffffffffa0338470 R15: ffff88021a055ba4
FS:  0000000000000000(0000) GS:ffff88033fca0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f467c0291b8 CR3: 0000000001a0b000 CR4: 00000000000007e0
Stack:
 ffff88021a055ab8 ffffffffa0332020 ffff88021a055b30 0000000000000001
 ffff88021a055b30 0000000000000000 ffff88021a055b18 0000000000000000
 ffff88021a055ba4 ffff88021a055b98 ffff88021a055ae8 ffffffffa033304c
Call Trace:
 [<ffffffffa0332020>] sm_ll_lookup_bitmap+0x40/0xa0 [dm_persistent_data]
 [<ffffffffa033304c>] sm_metadata_count_is_more_than_one+0x8c/0xc0 [dm_persistent_data]
 [<ffffffffa0333825>] dm_tm_shadow_block+0x65/0x110 [dm_persistent_data]
 [<ffffffffa0331b00>] sm_ll_mutate+0x80/0x300 [dm_persistent_data]
 [<ffffffffa0330e60>] ? set_ref_count+0x10/0x10 [dm_persistent_data]
 [<ffffffffa0331dba>] sm_ll_inc+0x1a/0x20 [dm_persistent_data]
 [<ffffffffa0332270>] sm_disk_new_block+0x60/0x80 [dm_persistent_data]
 [<ffffffff81520036>] ? down_write+0x16/0x40
 [<ffffffffa001e5c4>] dm_pool_alloc_data_block+0x54/0x80 [dm_thin_pool]
 [<ffffffffa001b23c>] alloc_data_block+0x9c/0x130 [dm_thin_pool]
 [<ffffffffa001c27e>] provision_block+0x4e/0x180 [dm_thin_pool]
 [<ffffffffa001fe9a>] ? dm_thin_find_block+0x6a/0x110 [dm_thin_pool]
 [<ffffffffa001c57a>] process_bio+0x1ca/0x1f0 [dm_thin_pool]
 [<ffffffff8111e2ed>] ? mempool_free+0x8d/0xa0
 [<ffffffffa001d755>] process_deferred_bios+0xc5/0x230 [dm_thin_pool]
 [<ffffffffa001d911>] do_worker+0x51/0x60 [dm_thin_pool]
 [<ffffffff81067872>] process_one_work+0x182/0x3b0
 [<ffffffff81068c90>] worker_thread+0x120/0x3a0
 [<ffffffff81068b70>] ? manage_workers+0x160/0x160
 [<ffffffff8106eb2e>] kthread+0xce/0xe0
 [<ffffffff8106ea60>] ? kthread_freezable_should_stop+0x70/0x70
 [<ffffffff8152af6c>] ret_from_fork+0x7c/0xb0
 [<ffffffff8106ea60>] ? kthread_freezable_should_stop+0x70/0x70
 [<ffffffff8152af6c>] ret_from_fork+0x7c/0xb0
 [<ffffffff8106ea60>] ? kthread_freezable_should_stop+0x70/0x70
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org # v3.10+

The dm_round_up function may overflow to zero.  In this case,
dm_table_create() must fail rather than go on to allocate an empty array
with alloc_targets().

This fixes a possible memory corruption that could be caused by passing
too large a number in "param->target_count".
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

There is a possible leak of snapshot space in case of crash.

The reason for space leaking is that chunks in the snapshot device are
allocated sequentially, but they are finished (and stored in the metadata)
out of order, depending on the order in which copying finished.

For example, supposed that the metadata contains the following records
SUPERBLOCK
METADATA (blocks 0 ... 250)
DATA 0
DATA 1
DATA 2
...
DATA 250

Now suppose that you allocate 10 new data blocks 251-260. Suppose that
copying of these blocks finish out of order (block 260 finished first
and the block 251 finished last). Now, the snapshot device looks like
this:
SUPERBLOCK
METADATA (blocks 0 ... 250, 260, 259, 258, 257, 256)
DATA 0
DATA 1
DATA 2
...
DATA 250
DATA 251
DATA 252
DATA 253
DATA 254
DATA 255
METADATA (blocks 255, 254, 253, 252, 251)
DATA 256
DATA 257
DATA 258
DATA 259
DATA 260

Now, if the machine crashes after writing the first metadata block but
before writing the second metadata block, the space for areas DATA 250-255
is leaked, it contains no valid data and it will never be used in the
future.

This patch makes dm-snapshot complete exceptions in the same order they
were allocated, thus fixing this bug.

Note: when backporting this patch to the stable kernel, change the version
field in the following way:
* if version in the stable kernel is {1, 11, 1}, change it to {1, 12, 0}
* if version in the stable kernel is {1, 10, 0} or {1, 10, 1}, change it
  to {1, 10, 2}
Userspace reads the version to determine if the bug was fixed, so the
version change is needed.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Move the bio->bi_remaining increment into dm_unhook_bio() so the
overwrite_endio() handler works as expected.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fixes the following sparse warning:

drivers/md/bcache/btree.c:2220:5: warning:
 symbol 'btree_insert_fn' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>

commit 566c09c5 raid5: relieve lock contention in get_active_stripe()

modified the locking in get_active_stripe() reducing the range
protected by the (highly contended) device_lock.
Unfortunately it reduced the range too much opening up some races.

One race can occur if get_priority_stripe runs between the
test on sh->count and device_lock being taken.
This will mean that sh->lru is not empty while get_active_stripe
thinks ->count is zero resulting in a 'BUG' firing.

Another race happens if __release_stripe is called immediately
after sh->count is tested and found to be non-zero.  If STRIPE_HANDLE
is not set, get_active_stripe should increment ->active_stripes
when it increments ->count from 0, but as it didn't think it was 0,
it doesn't.

Extending device_lock to cover the test on sh->count close these
races.

While we are here, fix the two BUG tests:
 -If count is zero, then lru really must not be empty, or we've
  lock the stripe_head somehow - no other tests are relevant.
 -STRIPE_ON_RELEASE_LIST is completely independent of ->lru so
  testing it is pointless.
Reported-and-tested-by: NBrassow Jonathan <jbrassow@redhat.com>
Reviewed-by: NShaohua Li <shli@kernel.org>
Fixes: 566c09c5Signed-off-by: NNeilBrown <neilb@suse.de>

commit 7a0a5355 md: Don't test all of mddev->flags at once.
made most tests on mddev->flags safer, but missed one.

When
commit 260fa034 md: avoid deadlock when dirty buffers during md_stop.
added MD_STILL_CLOSED, this caused md_check_recovery to misbehave.
It can think there is something to do but find nothing.  This can
lead to the md thread spinning during array shutdown.

https://bugzilla.kernel.org/show_bug.cgi?id=65721Reported-and-tested-by: NRichard W.M. Jones <rjones@redhat.com>
Fixes: 260fa034
Cc: stable@vger.kernel.org (3.12)
Signed-off-by: NNeilBrown <neilb@suse.de>

In alloc_thread_groups, worker_groups is a pointer to an array,
not an array of pointers.
So
   worker_groups[i]
is wrong.  It should be
   &(*worker_groups)[i]

Found-by: coverity
Fixes: 60aaf933Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

It was being open coded in a few places.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Joern Engel <joern@logfs.org>
Cc: Prasad Joshi <prasadjoshi.linux@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Chris Mason <chris.mason@fusionio.com>
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The new bio_split() can split arbitrary bios - it's not restricted to
single page bios, like the old bio_split() (previously renamed to
bio_pair_split()). It also has different semantics - it doesn't allocate
a struct bio_pair, leaving it up to the caller to handle completions.

Then convert the existing bio_pair_split() users to the new bio_split()
- and also nvme, which was open coding bio splitting.

(We have to take that BUG_ON() out of bio_integrity_trim() because this
bio_split() needs to use it, and there's no reason it has to be used on
bios marked as cloned; BIO_CLONED doesn't seem to have clearly
documented semantics anyways.)
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Neil Brown <neilb@suse.de>