Call the per-protocol unbind function rather than bind function on
NETLINK_DROP_MEMBERSHIP in netlink_setsockopt().
Signed-off-by: NRichard Guy Briggs <rgb@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have the netlink per-protocol optional bind function return an int error code
rather than void to signal a failure.

This will enable netlink protocols to perform extra checks including
capabilities and permissions verifications when updating memberships in
multicast groups.

In netlink_bind() and netlink_setsockopt() the call to the per-protocol bind
function was moved above the multicast group update to prevent any access to
the multicast socket groups before checking with the per-protocol bind
function.  This will enable the per-protocol bind function to be used to check
permissions which could be denied before making them available, and to avoid
the messy job of undoing the addition should the per-protocol bind function
fail.

The netfilter subsystem seems to be the only one currently using the
per-protocol bind function.
Signed-off-by: NRichard Guy Briggs <rgb@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicity and simplify code flow by moving the rcu_read_unlock() above
the condition and let the flow control exit naturally at the end of the
function.
Signed-off-by: NRichard Guy Briggs <rgb@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added a new ancillary load (bpf call in eBPF parlance) that produces
a 32-bit random number. We are implementing it as an ancillary load
(instead of an ISA opcode) because (a) it is simpler, (b) allows easy
JITing, and (c) seems more in line with generic ISAs that do not have
"get a random number" as a instruction, but as an OS call.

The main use for this ancillary load is to perform random packet sampling.
Signed-off-by: NChema Gonzalez <chema@google.com>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if allocating memory for vlan_pcpu_stats failed, the device can not be operated
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: NVenkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This ethtool patch primarily copies the ioctl command data structures
from/to the User space and invokes the driver hook.
Signed-off-by: NVenkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 0e280af0 ("tcp: introduce TCPSpuriousRtxHostQueues SNMP
counter") we added a logic to detect when a packet was retransmitted
while the prior clone was still in a qdisc or driver queue.

We are now confident we can do better, and catch the problem before
we fragment a TSO packet before retransmit, or in TLP path.

This patch fully exploits the logic by simply canceling the spurious
retransmit.
Original packet is in a queue and will eventually leave the host.

This helps to avoid network collapses when some events make the RTO
estimations very wrong, particularly when dealing with huge number of
sockets with synchronized blast.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Userspace applications can use IFA_F_MANAGETEMPADDR with RTM_NEWADDR
already to indicate that the kernel should take care of temporary
address management.

This patch adds related functionality to RTM_DELADDR. By setting
IFA_F_MANAGETEMPADDR a userspace application can indicate that the kernel
should delete all related temporary addresses as well.

A corresponding patch for the "ip addr del" command has been applied to
iproute2 already.
Signed-off-by: NHeiner Kallweit <heiner.kallweit@web.de>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ying Xue says:

====================
purge tipc_net_lock

Now tipc routing hierarchy comprises the structures 'node', 'link'and
'bearer'. The whole hierarchy is protected by a big read/write lock,
tipc_net_lock, to ensure that nothing is added or removed while code
is accessing any of these structures. Obviously the locking policy
makes node, link and bearer components closely bound together so that
their relationship becomes unnecessarily complex. In the worst case,
such locking policy not only has a negative influence on performance,
but also it's prone to lead to deadlock occasionally.

In order o decouple the complex relationship between bearer and node
as well as link, the locking policy is adjusted as follows:

- Bearer level
  RTNL lock is used on update side, and RCU is used on read side.
  Meanwhile, all bearer instances including broadcast bearer are
  saved into bearer_list array.

- Node and link level
  All node instances are saved into two tipc_node_list and node_htable
  lists. The two lists are protected by node_list_lock on write side,
  and they are guarded with RCU lock on read side. All members in node
  structure including link instances are protected by node spin lock.

- The relationship between bearer and node
  When link accesses bearer, it first needs to find the bearer with
  its bearer identity from the bearer_list array. When bearer accesses
  node, it can iterate the node_htable hash list with the node address
  to find the corresponding node.

In the new locking policy, every component has its private locking
solution and the relationship between bearer and node is very simple,
that is, they can find each other with node address or bearer identity
from node_htable hash list or bearer_list array.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a21a584d (tipc: fix neighbor
detection problem after hw address change) introduces a race condition
involving tipc_disc_delete() and tipc_disc_add/remove_dest that can
cause TIPC to dereference the pointer to the bearer discovery request
structure after it has been freed since a stray pointer is left in the
bearer structure.

In order to fix the issue, the process of resetting the discovery
request handler is optimized: the discovery request handler and request
buffer are just reset instead of being freed, allocated and initialized.
As the request point is always valid and the request's lock is taken
while the request handler is reset, the race doesn't happen any more.
Reported-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The node map variable - 'nodes' in bearer structure is only used by
bclink. When bclink accesses it, bc_lock is held. But when change it,
for instance, in tipc_bearer_add_dest() or tipc_bearer_remove_dest()
the bc_lock is not taken at all. To avoid any inconsistent data, we
should always grab bc_lock while accessing node map variable.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As bearer pointer is known in tipc_l2_device_event(), it's unnecessary
to search it again in tipc_disable_bearer(). If tipc_disable_bearer()
is replaced with bearer_disable() in tipc_l2_device_event(), this will
help us save a bit time when bearer is disabled.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'media_ptr' pointer in bearer structure which points to network
device, is protected by RCU. So, before netdevice is released,
synchronize_net() should be involved to prevent no any user of
the netdevice on read side from accessing it after it is freed.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now tipc routing hierarchy comprises the structures 'node', 'link'and
'bearer'. The whole hierarchy is protected by a big read/write lock,
tipc_net_lock, to ensure that nothing is added or removed while code
is accessing any of these structures. Obviously the locking policy
makes node, link and bearer components closely bound together so that
their relationship becomes unnecessarily complex. In the worst case,
such locking policy not only has a negative influence on performance,
but also it's prone to lead to deadlock occasionally.

In order o decouple the complex relationship between bearer and node
as well as link, the locking policy is adjusted as follows:

- Bearer level
  RTNL lock is used on update side, and RCU is used on read side.
  Meanwhile, all bearer instances including broadcast bearer are
  saved into bearer_list array.

- Node and link level
  All node instances are saved into two tipc_node_list and node_htable
  lists. The two lists are protected by node_list_lock on write side,
  and they are guarded with RCU lock on read side. All members in node
  structure including link instances are protected by node spin lock.

- The relationship between bearer and node
  When link accesses bearer, it first needs to find the bearer with
  its bearer identity from the bearer_list array. When bearer accesses
  node, it can iterate the node_htable hash list with the node
  address to find the corresponding node.

In the new locking policy, every component has its private locking
solution and the relationship between bearer and node is very simple,
that is, they can find each other with node address or bearer identity
from node_htable hash list or bearer_list array.

Until now above all changes have been done, so tipc_net_lock can be
removed safely.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the media_ptr pointer is protected with tipc_net_lock write lock
on write side; tipc_net_lock read lock is used to read side. As the
part of effort of eliminating tipc_net_lock, we decide to adjust the
locking policy of media_ptr pointer protection: on write side, RTNL
lock is use while on read side RCU read lock is applied.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently on both paths of message transmission and reception, the
read lock of tipc_net_lock must be held before bearer is accessed,
while the write lock of tipc_net_lock has to be taken before bearer
is configured. Although it can ensure that bearer is always valid on
the two data paths, link and bearer is closely bound together.

So as the part of effort of removing tipc_net_lock, the locking
policy of bearer protection will be adjusted as below: on the two
data paths, RCU is used, and on the configuration path of bearer,
RTNL lock is applied.

Now RCU just covers the path of message reception. To make it possible
to protect the path of message transmission with RCU, link should not
use its stored bearer pointer to access bearer, but it should use the
bearer identity of its attached bearer as index to get bearer instance
from bearer_list array, which can help us decouple the relationship
between bearer and link. As a result, bearer on the path of message
transmission can be safely protected by RCU when we access bearer_list
array within RCU lock protection.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert bearer_list to RCU list. It's protected by RTNL lock on
update side, and RCU read lock is applied to read side.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the tipc network initialization(ie, tipc_net_start routine) is
under RTNL protection, its corresponding deinitialization part(ie,
tipc_net_stop routine) should be protected by RTNL too.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the 'tipc_ptr' pointer is protected by tipc_net_lock
write lock on write side, and RCU read lock is applied to read
side. In addition, there have two paths on write side where we
may change variables pointed by the 'tipc_ptr' pointer: one is
to configure bearer by tipc-config tool and another one is that
bearer status is changed by notification events of its attached
interface. But on the latter path, we improperly deem that
accessing 'tipc_ptr' pointer happens on read side with
rcu_read_lock() although some variables pointed by the 'tipc_ptr'
pointer are changed possibly.

Moreover, as now the both paths are guarded by RTNL lock, it's
better to adjust the locking policy of 'tipc_ptr' pointer
protection, allowing RTNL instead of tipc_net_lock write lock to
protect it on write side, which will help us purge tipc_net_lock
in the future.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There have two paths where we can configure or change bearer status:
one is that bearer is configured from user space with tipc-config
tool; another one is that bearer is changed by notification events
from its attached interface. On the first path, one dedicated
config_mutex lock is guarded; on the latter path, RTNL lock has been
placed to serialize the process of dealing with interface events.
So, if RTNL lock is also used to protect the first path, this will
not only extremely help us simplify current locking policy, but also
config_mutex lock can be deleted as well.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Tested-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: ndo_set_config/ifmap cleanups

This patch series removes a bunch of useless ndo_set_config in non
PCMCIA Ethernet drivers.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sxgbe_config() denies changing the base address and interrupt, and
ignores all other 'struct ifmap' members, which means that it is useless
as is, so let's remove it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cpmac_config() refuses changing the base address parameter, and ignores
all other parameters, which means that it is pretty useless as it is, so
let's remove it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethoc_config() returns -ENOSYS and does not implement anything useful,
let's remove it such that net/core/dev_ioctl.c::dev_ifsioc can return
something meaningful like -EOPNOTSUPP.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature allows multiple channels to be used by each virtual NIC.
It is available on Hyper-V host 2012 R2.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make tcp_cwnd_application_limited() static and move it from tcp_input.c to
tcp_output.c
Signed-off-by: NWeiping Pan <wpan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't rely on driver files or other headers having this file included.

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will simplify the new reassembly backport
with no code changes being required.

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Cc: David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The busy polling socket option adds support for sockets to busy wait on data
arriving on the napi queue from which they have most recently received a frame.
Currently only tcp and udp support this feature, but theres no reason sctp can't
do so as well.  Add it in so appliations can take advantage of it
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Daniel Borkmann <dborkman@redhat.com>
CC: netdev@vger.kernel.org
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make local functions static, because these are used only in this
file.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NByungho An <bh74.an@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently broadcasts are handled in network RX context, where
the packets are sent through netif_rx.  This means that the number
of macvlans will be constrained by the capacity of netif_rx.

For example, setting up 4096 macvlans practically causes all
broadcast packets to be dropped as the default netif_rx queue
size simply can't handle 4096 skbs being stuffed into it all
at once.

Fundamentally, we need to ensure that the amount of work handled
in each netif_rx backlog run is constrained.  As broadcasts are
anything but constrained, it either needs to be limited per run
or moved to process context.

This patch picks the second option and moves all broadcast handling
bar the trivial case of packets going to a single interface into
a work queue.  Obviously there also needs to be a limit on how
many broadcast packets we postpone in this way.  I've arbitrarily
chosen tx_queue_len of the master device as the limit (act_mirred
also happens to use this parameter in a similar way).

In order to ensure we don't exceed the backlog queue we will use
netif_rx_ni instead of netif_rx for broadcast packets.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the helper __dev_forward_skb which is identical to
dev_forward_skb except that it doesn't actually inject the skb into
the stack.  This is useful where we wish to have finer control over
how the packet is injected, e.g., via netif_rx_ni or netif_receive_skb.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a TCP_FASTOPEN socket option to get a max backlog on its
listener to getsockopt().
Signed-off-by: NKenjiro Nakayama <nakayamakenjiro@gmail.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the generic bits from genphy_config_init() instead of implementing
the same functionality again.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull x86 fix from Ingo Molnar:
 "This fixes the preemption-count imbalance crash reported by Owen
  Kibel"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix CMCI preemption bugs