These functions should just silently fail when we're not powered on
instead of trying to send HCI commands.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The return parameters for Set Device Class should consist of the new
class value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

We should assume a value of 0 for the device class when powered off.
The appropriate place to do this is in hci_dev_do_close().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The short name is part of the Read Controller Info response and should
be appropriately filled in based on the value of hdev->short_name.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

Since we can't reliably track the short name changes just assume that we
had a change whenever there's a pending mgmt command. In the worst case
we just get one unnecessary name_changed signal.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch makes it possible to set the local name before powering on
the device. The name will be applied using the hci_write_local_name
command once the device gets powered on.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The local name should only be updated as a consequence of a
hci_read_local_name if we are in the HCI_SETUP state. In all other
scenarios it should only be updated through hci_write_local_name.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

It's possible to provide a short name through the mgmt interface and
this name can be used for EIR generation when the full name doesn't fit
there. This patch adds the preliminary tracking of the provided short
name.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

Currently there are no events to other management sockets if the class of
device got changed. So make sure they are sent.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The current handling of the discoverable timeout was missing the proper
handling of the timeout when the mode was already set. Now the command
can be used to expire or retrigger the timeout.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add one extra sanity check to ensure that the supplied timeout value is
actually valid in this context.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Whenever we update the local device name the EIR data also needs to be
updated to reflect this. The update_eir() function in mgmt.c depends on
hdev->dev_name to be up to date so the patch also makes sure that the
mgmt function is called from hci_event.c after the update has happened.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

When powering off we should assume that the EIR data isn't valid
anymore. This patch makes sure it gets cleared in hci_dev_do_close and
thereby ensures that a correct new EIR is recreated when powering on
again.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements support for the Set LE mgmt command. Now, in
addition to the enable_le module parameter user space needs to send an
explicit Enable LE command to enable LE support.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The test for SSP support needs to be earlier in the set_ssp function so
that we return an error when SSP is not supported even when the device
is powered off.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The control channel can be also monitored, so include timestamps here
as well. And make sure management events get their timestamp when they
are created.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some controllers preserve their EIR data even after a reset so we need
to explicitly clear this during the device setup procedure.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The hdev->eir buffer needs to be cleared when clearing the EIR data.
Otherwise subsequent attempts at setting the EIR to something valid
again may fail because the code thinks that the EIR hasn't changed.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes setting the EIR properly when the SSP flag has been set
when powered off (in such a case there is no pending Set_SSP command).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

In this case we need to use braces in both branches.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

WARNING: min() should probably be min_t(__u16, scb->expect, count)
+		len = min(scb->expect, (__u16)count);

WARNING: Statements terminations use 1 semicolon
+	INIT_LIST_HEAD(&conn->chan_list);;
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

WARNING: Statements terminations use 1 semicolon
+	return err;;

WARNING: space prohibited between function name and open parenthesis '('
+		err = cmd_status (sk, index, MGMT_OP_CONFIRM_NAME,
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch makes it possible to enable SSP through mgmt even when
powered off. The setting will then get automatically actiated when
powering on.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The kernel has no need to track the hci_read_ssp_mode command since it
has the hci_sent_cmd_data function to check what value was set when
hci_write_ssp_mode completes.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch makes it possible to change the Link Security setting while
powered off and have it automatically enabled when powering on a device.
To track the desired state once powered on a new HCI_LINK_SECURITY flag
is added.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

Use locked and unlocked versions to help removing socket
locks from l2cap core functions.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Split to locked and unlocked versions of l2cap_state_change helping
to remove socket locks from l2cap code.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Reviewed-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Channel lock will be used to lock L2CAP channels which are locked
currently by socket locks.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Reviewed-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Usage of RCU list looks not reasonalbe for a number of reasons:
our code sleep and we had to use socket spinlocks. Most parts
of code are updaters thus there is little sense to use RCU.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Reviewed-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The ID is found on Asus K54HR and K53U.
Blacklist the AR3011-based device ID [0489:e03d]
and add to ath3k.c for firmware loading.

Below is the output of usb-devices script:

Before the fiwmware loading:

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e03d Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

After the fiwmware loading:

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3005 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NKeng-Yu Lin <kengyu@canonical.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The connectable/discoverable flags need to be changed before sending the
response since otherwise the settings value will be incorrect.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

Now that most flags are persistent, only the LE_SCAN flag should be
cleared after a reset.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

When powered off and doing changes to the Connectable or Discoverable
setting we should also send an appropriate New Settings event in
addition to the command response.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

The New Settings event needs to be sent from quite many places so it
makes sense to have a convenience function for it to simplify the code.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

We should not stop iterating through the various settings if powered off
since most may still be set even then.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

When switching connectable mode off any pending discoverable timeout
must also be disabled to avoid duplicate write_scan_enable commands.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch makes it possible to toggle the connectable & discoverable
settings when powered off. Two new hdev->dev_flags flags are added to
track what the scan mode should be when the device is finally powered
on.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

When mgmt is not in use the HCI_PAIRABLE flag will get implicitly set so
that pairing still works with old user space versions. However, as soon
as mgmt comes into play we should clear this flag so that it can be
properly set through the set_pairable command by user space.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch ensures that Set Fast Connectable fails apropriately if we
are not already in a connectable state (which is a pre-requisite for
fast connectable).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>