- 28 11月, 2007 1 次提交
-
-
由 Jonas Stare 提交于
There is a problem in some hardware where the kernel will stall for 35 seconds waiting for disks that don't exist. This patch will skip waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe" as a kernel option and the disk is not marked as 'present' (like when you set the geometry by hand). If no noprobe-option is set the code will work (more or less) as the original but if set the code will skip the ide_wait_not_busy() for that drive. Even if there would be a drive there and it is still busy afterwards it should not matter since it isn't probed for later. The code also honors the MAX_DRIVES variable instead of assuming that there will be two harddrives on the bus. Bart: minor cleanups Signed-off-by: NJonas Stare <jonas.stare@purplescout.se> CC: Andrew Morton <akpm@linux-foundation.org>, Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 06 11月, 2007 1 次提交
-
-
由 Tejun Heo 提交于
Terminates id->model string before invoking strstr() in do_identify(). Signed-off-by: NTejun Heo <tj@home-tj.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 23 10月, 2007 2 次提交
-
-
由 FUJITA Tomonori 提交于
git-drivers/ide/ide-probe.c: In function 'hwif_init': drivers/ide/ide-probe.c:1327: error: implicit declaration of function 'sg_init_table' Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
由 Jens Axboe 提交于
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
- 20 10月, 2007 3 次提交
-
-
* Add ide_device_add() helper and convert host drivers to use it instead of open-coded variants. * Make ide_pci_setup_ports() and do_ide_setup_pci_device() take 'u8 *idx' argument instead of 'ata_index_t *index'. * Remove no longer needed ata_index_t. * Unexport probe_hwif_init() and make it static. * Unexport ide_proc_register_port(). There should be no functionality changes caused by this patch (sgiioc4.c: ide_proc_register_port() requires hwif->present to be set and it won't be set if probe_hwif_init() fails). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Add ->fixup method to ide_hwif_t. * Set hwif->fixup in ide_pci_setup_ports() to d->fixup. * Use hwif->fixup in probe_hwif(). * Use probe_hwif_init() instead of probe_hwif_init_with_fixup() in ide_setup_pci_device(). * Add 'fixup' argument to ide_register_hw() and use it to set hwif->fixup, update all ide_register_hw() users accordingly. * Convert ide-cs/delkin_cb host drivers to use ide_register_hw(). * Restore hwif->fixup in ide_hwif_restore(). * Remove ide_register_hw_with_fixup(), probe_hwif_init_with_fixup() and 'fixup' argument from probe_hwif(). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Add hwif_register_devices() helper to fix code duplication between probe_hwif_init_with_fixup() and ideprobe_init(). Also remove stale comment while at it. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 19 10月, 2007 1 次提交
-
-
Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma] and then remove no longer needed hwif->no_lba48[_dma]. As a side-effect this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore(). Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 17 10月, 2007 3 次提交
-
-
ATAPI devices with broken DMA support should be handled by DMA blacklist and for debugging purposes we have new shiny "hdx=nodma" kernel paremeter. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* hpt34x.c: disable DMA masks for HPT345 (hwif->autodma is zero so DMA won't be enabled anyway). * trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag (hwif->autodma is zero so DMA won't be enabled anyway). * Check noautodma global variable instead of drive->autodma in ide_tune_dma(). This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris, au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers. * Remove hwif->autodma (it was not checked by IDE core code anyway) and drive->autodma (was set by all host drivers - except HPT345/TRM290 special cases - unless "ide=nodma" was used). While at it: - remove needless printk() from icside.c - remove stale FIXME/comment from ide-probe.c - don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c (this setting was always later over-ridden by host drivers anyway) Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend on BIOS for programming device/controller for DMA. Set it in cy82c693, generic, ns87415, opti621 and trm290 host drivers. * Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520 host driver. * Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag. * Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check implementations. Fix all places checking for presence of ->ide_dma_check hook to check for ->ide_dma_on instead. * Remove no longer needed code from config_drive_for_dma(). * Make ide_tune_dma() static. v2: * Fix config_drive_for_dma() return values. * Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding dummy config_drive_for_dma() inline. * Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check(). * Fix init_hwif_it8213() comment. There should be no functionality changes caused by this patch. Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 16 10月, 2007 1 次提交
-
-
由 Jens Axboe 提交于
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
- 13 10月, 2007 1 次提交
-
-
Need to probe slave device first to make it release PDIAG- (this is required for correct device side cable detection). Based on libata commit f31f0cc2. Thanks to Craig for testing this patch. Cc: Craig Block <chblock3@yahoo.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 12 10月, 2007 1 次提交
-
-
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags and set them in ht6560, cmd640, cmd64x and sc1200 host drivers. * Add set_pio_mode_abuse() for checking if host driver has a non-standard ->tuneproc() implementation and use it in do_special(). * Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find the maximum PIO mode supported by the host), also add ide_set_max_pio() wrapper for ide_set_pio() to use for auto-tuning. Convert users of ->tuneproc to use ide_set{_max}_pio() where possible. This leaves only do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as a direct users of ->tuneproc. * Remove no longer needed ide_get_best_pio_mode() calls and printk-s reporting PIO mode selected from ->tuneproc implementations. * Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const. * Remove stale comment from ide_config_drive_speed(). v2: * Fix "ata_" prefix (Noticed by Jeff). v3: * Minor cleanups/fixups per Sergei's suggestions. v4: * Fix compile problem in drivers/ide/pci/cmd640.c (Noticed by Andrew Morton). * Improve some ->set_pio_mode comments. Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 24 7月, 2007 1 次提交
-
-
由 Jens Axboe 提交于
Some of the code has been gradually transitioned to using the proper struct request_queue, but there's lots left. So do a full sweet of the kernel and get rid of this typedef and replace its uses with the proper type. Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
- 18 7月, 2007 1 次提交
-
-
由 Christoph Lameter 提交于
kmalloc_node() and kmem_cache_alloc_node() were not available in a zeroing variant in the past. But with __GFP_ZERO it is possible now to do zeroing while allocating. Use __GFP_ZERO to remove the explicit clearing of memory via memset whereever we can. Signed-off-by: NChristoph Lameter <clameter@sgi.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 10 7月, 2007 2 次提交
-
-
由 Robert P. J. Day 提交于
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Matthias Kaehlcke 提交于
The IDE driver uses a semaphore as mutex. Use the mutex API instead of the (binary) semaphore. Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 04 7月, 2007 1 次提交
-
-
由 Alan Cox 提交于
Found by a static analyser. It is in theory possible we dereference dev->id when it has become invalid. Re-order to avoid this. Not needed for new-ide as we no longer support the crazy exabyte nest stuff Signed-off-by: NAlan Cox <alan@redhat.com> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 08 6月, 2007 1 次提交
-
-
The DMA support for RAID mode broke after: commit 71ef51cc Author: Jens Axboe <axboe@suse.de> Date:  Fri Jul 28 09:02:17 2006 +0200   [PATCH] it821x: fix ide dma setup bug   Only enable dma for a valid speed setting.   Signed-off-by: Jens Axboe <axboe@suse.de> commit 0a8348d0 Author: Jens Axboe <axboe@suse.de> Date:  Fri Jul 28 08:58:26 2006 +0200   [PATCH] ide: if the id fields looks screwy, disable DMA   It's the safer choice. Originally due to a bug in itx821x, but a   generally sound thing to do.   Signed-off-by: Jens Axboe <axboe@suse.de> However it worked by pure luck before Jens' fixes: bogus ide_dma_enable() usage in it821x driver combined with loosy check in ide_dma_verbose() allowed the hardware to operate in DMA mode. When these problems were fixed the DMA support broke... The source root for the regression turned out to be that the it821x.c code was clearing too much of id->field_valid. The IDE core code was using the original value of id->field_valid to do the tuning but later DMA got disabled in ide_dma_verbose() because of the incorrect id->field_valid fixup. Fix it. While at it: * Do fixup() after probing the drives but before tuning them (which is also OK w.r.t. ide_undecoded_slave() fixup). This change fixes device IDENTIFY data to be consistent before/after the tuning and allows us to remove extra re-tuning of drives from it821x_fixups(). * Fake MWDMA0 enabled/supported bits in IDENTIFY data if the device has DMA capable bit set (this is just to tell the IDE core that DMA is supported since it821x firmware takes care of DMA mode programming). * Don't touch timing registers and don't program transfer modes on devices et all when in RAID mode - depend solely on firmware to do the tuning (as suggested by Alan Cox and done in libata pata_it821x driver). Thanks for testing the patch goes out to Thomas Kuther. Cc: Thomas Kuther <gimpel@sonnenkinder.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jens Axboe <axboe@suse.de> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 10 5月, 2007 1 次提交
-
-
* create_proc_ide_interfaces() tries to add /proc entries for every probed and initialized IDE port, replace it by ide_proc_register_port() which does it only for the given port (also rename destroy_proc_ide_interface() to ide_proc_unregister_port() for consistency) * convert {create,destroy}_proc_ide_interface[s]() users to use new functions * pmac driver depended on proc_ide_create() to add /proc port entries, fix it * au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them * there is now no need to add /proc entries for IDE ports in proc_ide_create() so don't do it * proc_ide_create() needs now to be called before drivers are probed - fix it, while at it make proc_ide_create() create /proc "ide" directory Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 04 3月, 2007 1 次提交
-
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 17 2月, 2007 2 次提交
-
-
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0' make these functions void and while at it drop "ide_" prefix * fix comment for __ide_dma_off_quietly() * make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix v2: * while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(), sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}() and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly() [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ] Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly) 0 when DMA needs to be enabled (== need to call ->ide_dma_on) 1 when DMA setting shouldn't be changed * fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly v2: * updated for scc_pata Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 08 2月, 2007 1 次提交
-
-
由 Hannes Reinecke 提交于
This patch implements ACPI integration for generic IDE devices. The ACPI spec mandates that some methods are called during suspend and resume. And consequently there most modern Laptops cannot resume properly without it. According to the spec, we should call '_GTM' (Get Timing) upon suspend to store the current IDE adapter settings. Upon resume we should call '_STM' (Set Timing) to initialize the adapter with the stored settings; afterwards '_GTF' (Get Taskfile) should be called which returns a buffer with some IDE initialisation commands. Those commands should be passed to the drive. There are two module params which control the behaviour of this patch: 'ide=noacpi' Do not call any ACPI methods (Disables any ACPI method calls) 'ide=acpigtf' Enable execution of _GTF methods upon resume. Has no effect if 'ide=noacpi' is set. 'ide=acpionboot' Enable execution of ACPI methods during boot. This might be required on some machines if 'ide=acpigtf' is selected as some machines modify the _GTF information depending on the drive identification passed down with _STM. Signed-off-by: NHannes Reinecke <hare@suse.de> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
- 12 12月, 2006 1 次提交
-
-
由 Boaz Harrosh 提交于
While working on bidi support at struct request level I have found that blk_queue_activity_fn is actually never used. The only user is in ide-probe.c with this code: /* enable led activity for disk drives only */ if (drive->media == ide_disk && hwif->led_act) blk_queue_activity_fn(q, hwif->led_act, drive); And led_act is never initialized anywhere. (Looking back at older kernels it was used in the PPC arch, but was removed around 2.6.18) Unless it is all for future use off course. (this patch is against linux-2.6-block.git as off 2006/12/4) Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com> Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
-
- 03 10月, 2006 1 次提交
-
-
由 Randy Dunlap 提交于
Check driver layer return values in IDE core. Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 03 7月, 2006 1 次提交
-
-
由 Thomas Gleixner 提交于
Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 27 6月, 2006 1 次提交
-
-
由 Greg Kroah-Hartman 提交于
Also removes the ide drive devfs_name field as it's no longer needed Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 20 6月, 2006 1 次提交
-
-
由 David S. Miller 提交于
This ugly hack was long overdue to die. It was a way to print out Sparc interrupts in a more freindly format, since IRQ numbers were arbitrary opaque 32-bit integers which vectored into PIL levels. These 32-bit integers were not necessarily in the 0-->NR_IRQS range, but the PILs they vectored to were. The idea now is that we will increase NR_IRQS a little bit and use a virtual<-->real IRQ number mapping scheme similar to PowerPC. That makes this IRQ printing hack irrelevant, and furthermore only a handful of drivers actually used __irq_itoa() making it even less useful. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 3月, 2006 1 次提交
-
-
由 Kumar Gala 提交于
In some embedded systems the IDE hardware interface may only support 16-bit or smaller accesses. Allow the interface to specify if this is the case and don't allow the drive or user to override the setting. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 04 2月, 2006 1 次提交
-
-
由 Richard Purdie 提交于
This patch stops CompactFlash devices being marked as removable. They are not removable (as defined by Linux) as the media and device are inseparable. When a card is removed, the whole device is removed from the system and never sits in a media-less state. This stops some nasty udev device creation/destruction loops. Further, once this change is made, there is no need for ide to can be removed from ide_drive_t. Signed-off-by: NRichard Purdie <rpurdie@rpsys.net> Acked-by: NBartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 13 1月, 2006 1 次提交
-
-
由 Jens Axboe 提交于
There's a problem with the REQ_BLOCK_PC handling as well (bad ->data_len handling) where it could actually complete a request ahead of time. I suggest we just back this out for now, I will resubmit it later when I'm fully confident in it. This reverts commit 8672d571Signed-off-by: NJens Axboe <axboe@suse.de> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 10 1月, 2006 1 次提交
-
-
由 Aleksey Makarov 提交于
The patch changes semaphores that are initialized as locked to complete(). Source: MontaVista Software, Inc. Modified-by: NSteven Rostedt <rostedt@goodmis.org> The following patch is from Montavista. I modified it slightly. Semaphores are currently being used where it makes more sense for completions. This patch corrects that. Signed-off-by: NAleksey Makarov <amakarov@ru.mvista.com> Signed-off-by: NSteven Rostedt <rostedt@goodmis.org> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
- 09 1月, 2006 1 次提交
-
-
由 Jens Axboe 提交于
This patch makes IDE use the new blk_complete_request() interface. There's still room for improvement, as __ide_end_request() really could drop the lock after getting HWGROUP->rq (why does it need to hold it in the first place? If ->rq access isn't serialized, we are screwed anyways). Signed-off-by: NJens Axboe <axboe@suse.de>
-
- 07 11月, 2005 2 次提交
-
-
由 Jesper Juhl 提交于
This is the remaining misc drivers/ part of the big kfree cleanup patch. Remove pointless checks for NULL prior to calling kfree() in misc files in drivers/. Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com> Acked-by: NAristeu Sergio Rozanski Filho <aris@cathedrallabs.org> Acked-by: NRoland Dreier <rolandd@cisco.com> Acked-by: NPierre Ossman <drzeus@drzeus.cx> Acked-by: NJean Delvare <khali@linux-fr.org> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Acked-by: NLen Brown <len.brown@intel.com> Acked-by: N"Antonino A. Daplas" <adaplas@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Deepak Saxena 提交于
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 10 8月, 2005 1 次提交
-
-
由 Christoph Lameter 提交于
1. Move hwif_to_node to ide.h 2. Use hwif_to_node in ide-disk.c Signed-off-by: NChristoph Lameter <clameter@sgi.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 05 8月, 2005 1 次提交
-
-
由 Ravikiran G Thirumalai 提交于
Patch fixes oops caused by ide interfaces not on pci. pcibus_to_node causes the kernel to crash otherwise. Patch also adds a BUG_ON to check if hwif is NULL. Signed-off-by: NChristoph Lameter <christoph@lameter.com> Signed-off-by: NShai Fultheim <shai@scalex86.org> Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org> Cc: Andi Kleen <ak@muc.de> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-