Make the driver allocate dma buffers to store horizontal and scaler coeffs.
Use the scaler library api to choose and copy scaler coefficients to a
the above buffers based on the scaling ratio. Since the SC block comes after
the de-interlacer, make sure that the source height is doubled if de-interlacer
was used.

These buffers now need to be used by VPDMA to load the coefficients into the
SRAM within SC.

In device_run, add configuration descriptors which have payloads pointing to
the scaler coefficients in memory. Use the members in sc_data handle to prevent
addition of these descriptors if there isn't a need to re-load coefficients into
SC. This comes helps unnecessary re-loading of the coefficients when we switch
back and forth between vpe contexts.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The SC block in VPE/VIP contains a SRAM within it. This internal memory
requires to be loaded with appropriate scaler coefficients from a contiguous
block of memory through VPDMA.

The horizontal and vertical scaler each require 2 sets of scaler coefficients
for luma and chroma scaling. The horizontal polyphase scaler requires
coefficients for a 32 phase and 8 tap filter. Similarly, the vertical scaler
requires coefficients for a 5 tap filter.

The choice of the scaler coefficients depends on the scaling ratio. Add
coefficient tables for different scaling ratios in sc_coeffs.h. In the case of
horizontal downscaling, we need to consider the change in ratio caused by
decimation performed by the horizontal scaler.

In order to load the scaler coefficients via VPDMA, a configuration descriptor
is used in block mode. The payload for the descriptor is the scaler coefficients
copied to memory. Coefficients for each phase have to be placed in memory in a
particular order understood by the scaler hardware.

The choice of the scaler coefficients, and the loading of the coefficients from
our tables to a contiguous buffer is managed by the functions
sc_set_hs_coefficients and sc_set_vs_coefficients.

The sc_data handle is now added with some parameters to describe the state of
the coefficients loaded in the SC block. 'loaded_coeff_h' and 'loaded_coeff_v'
hold the address of the last dma buffer which was used by VPDMA to copy
coefficients. This information can be used by a vpe mem-to-mem context to decide
whether it should load coefficients or not. 'hs_index' and 'vs_index' provide
some optimization by preventing loading of coefficients if the scaling ratio
didn't change between 2 contexts. 'load_coeff_h' and 'load_coeff_v' tell the
vpe/vip driver whether we need to load the coefficients through VPDMA or not.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

VPE and VIP IPs in DAR7x contain a scaler(SC) sub block. Create a library which
will perform scaler block related configurations and hold SC register
definitions. The functions provided by this library will be called by the vpe
and vip drivers using a sc_data handle.

The vpe_dev holds the sc_data handle. The handle represents an instance of the
SC hardware, and the vpe driver uses it to access the scaler register offsets
or helper functions to configure these registers.

We move the SC register definitions to sc.h so that they aren't specific to
VPE anymore. The register offsets are now relative to the sub-block, and not the
VPE IP as a whole. In order for VPDMA to configure registers, it requires it's
offset from the top level VPE module. A macro called GET_OFFSET_TOP is added to
return the offset of the register relative to the VPE IP.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The (d)qbuf ioctls were traced in the low-level v4l2 ioctl function. The
trace was outside the serialization lock, so that can affect the usefulness
of the timing. In addition, the __user pointer was expected instead of a
proper kernel pointer.

By moving the tracepoints to video_usercopy we ensure that the trace calls
use the correct kernel pointer, and that it happens right after the ioctl
call to the driver, so certainly inside the serialization lock.

In addition, we only trace if the call was successful.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NWade Farnsworth <wade_farnsworth@mentor.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Change "packet" to "packed" where the doc is talking about packed data
formats.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The xref to the v4l2-mbus-pixelcode-yuv8 table gets rendered as "Table
4.22, “YUV Formats”", so use the verb in the third person singular
because it refers to "Table":
  s/list/lists/
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Do not shift the already 7bit i2c address.
Print a message also for write+read transactions.
For write+read, print the read buffer correctly instead of using the write
buffer.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The two drivers LGDT3305 and TDA18271C2DD were not autoselected, so the
cx231xx_dvb module could not be loaded when MEDIA_SUBDRV_AUTOSELECT=y.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add the missing unlock before return from function bcm2048_rds_fifo_receive()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.

Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Return 0 if the new timings are equal to the current timings as
it caused extra cp-loss/lock interrupts.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The free-run mode can be board-specific.

Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Must clear timings before setting after test to recover.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Clear i2c_clients ptr when unregistered.
Warn if configured i2c-addr is zero.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The STDI block may measure wrong values, especially for lcvs and lcf.
If the driver can not find any valid timing, the STDI block is restarted
to measure the video timings again. The function will return an error,
but the restart of STDI will generate a new STDI interrupt and the format
detection process will restart.

Copied from adv7604.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Wait 5ms after main reset. The data-sheet doesn't specify the wait
after i2c-controlled reset, so using same value as after pin-controlled
reset.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.

In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.

This adds the possibility to change output config between the fields and standards.

This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

For edid with no Source Physical Address (spa), set
spa-location to default and use correct values from edid.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Added support for YCrCb analog input.

If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.

See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.

Make sure that when switching inputs the RGB quantization range is
updated as well.

Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The method of disabling the irq-output pin caused many "empty"
interrupts. Instead, actually disable/enable the interrupts by
changing the interrupt masks.

Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI
events happen while the interrupt is masked those events will be ignored
when the interrupt is unmasked.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4
of register 0x91 was set incorrectly (must be 0).

These bits are undocumented, so we shouldn't modify them to values different
from what the datasheet specifies.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This simplified the code quite a bit.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some sources are initially detected as DVI, and change to HDMI later.
This must be detected to set the right RGB quantization range.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Signed-off-by: NMats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If the restart_stdi_once trick fails to find a valid
format the flag was never reset.
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>