max17047 is improved version of max17042 chip. It has few HW bug
fixes with minor changes in register set.

max17050 is same as max17047 chip except its silicon packging. So from
driver's point of view there is no difference btw max1047 and max1050.

This patch adds the support to dynamically detect the chip type and
adds steps to initialize the max17047 chip.
Signed-off-by: NRamakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>

By using cm_notify_event function, charger driver can report several
charger events (e.g. battery full and external power in/out, etc) to
Charger-Manager. Charger-Manager can properly and immediately control
chargers by the reported event.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>

Charger-Manager needs to check battery health in normal state
as well as suspend-to-RAM state. When the battery is fully charged,
Charger-Manager needs to determine when the chargers restart charging.

This patch allows Charger-Manager to monitor battery health in normal
state and handle operation for chargers after battery is fully charged.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>

Driver support for the Summit I²C battery charger. This is used in some
Intel devices.
Signed-off-by: NBruce E. Robertson <bruce.e.robertson@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>

Add power on reset (POR) init procedure defined by the maxim
appnote. Using this procedure ensures that the part is
configured/initialized correctly at POR and improves early accuracy of
the fuel gauge and informs the fuel gauge with the battery
characterization parameters.  The battery characterization parameters
come from the maxim characterization procedure.
Signed-off-by: NRamakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>

align the register names with max17042 data sheet removing
registers that are marked reserved that are not used.

Add register definitions defined in the maxim initialization appnote
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>

Now that this driver is named more generally, this change updates
the internal variables, defines and functions to use this new name.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This driver for the bq20z75 implemented the register spec defined
by the SBS standard. As this is not unique to this the TI part this
was originally written for, we can generalize this driver to
show its support for any SBS compliant battery.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Charger Manager provides power-supply-class aggregating
information from multiple chargers and a fuel-gauge.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Because battery health monitoring should be done even when suspended,
it needs to wake up and suspend periodically. Thus, userspace battery
monitoring may incur too much overhead; every device and task is woken
up periodically. Charger Manager uses suspend-again to provide
in-suspend monitoring.

This patch allows to monitor battery health in-suspend state.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This patch supports additional properties (PRESENT, CYCLE_COUNT,
VOLTAGE_MAX, VOLTAGE_MIN_DESIGN, CURRENT_NOW, CURRENT_AVG,
CHARGE_FULL, and TEMP).
Plus, initialization code for registers is added.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Adding support for external power change notification. One problem found
is that there is a lag time before the sensor will return a new status.
To ensure that we only fire off the power_supply_changed event when the
status returned from the sensor is actually different, we delay sending
the the notification, and instead poll on it looking for a change. The
amount of time to poll is configurable via platform data.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

The ISP1704/1707 chip can be put to full power down
state by asserting the CHIP_SEL line. This patch enables
platform or board specific hooks to put the device into
power down mode in case not needed.

This patch is a preparation for enabling this powering
routine in n900 (rx-51) devices.

Thanks to Heikki Krogerus for helping out with the patch.
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: NHeikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

MAX8903 is an integrated battery charger and selector with two
power inputs (USB and AC adapter). This driver enables the charger,
handles interrupts, and provides power-supply-class information to
userland.

Tested on Exynos4 NURI / S5PC210 SLP7 boards.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

With the support of platform data, now adding support for option i2c
retries on read/write failures. Ths is specified through the optional
platform data.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Adding support for an optional gpio for battery detection. This is
passed in through the i2c platform data. It also accepts another
field, battery_detect_present to signify the gpio state which means
the battery is present, either 0 (low) or 1 (high).
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This patch adds support for the bq27000 battery to the bq27x00 driver.
The bq27000 is similar to the bq27200 except that it uses the HDQ bus
instead of I2C to communicate with the host system.

The driver is implemented as a platform driver. The driver expects to be
provided with a read callback function through its platform data. The read
function is assumed to do the lowlevel HDQ handling and read out the value
of a certain register.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>

The MAX17042 is a fuel gauge with an I2C interface for lithium-ion
betteries. Unlike its predecessor MAX17040, MAX17042 uses 16bit
registers. Besides, MAX17042 has much more features than MAX17040; e.g.,
a thermistor, current and current accumulation measurement, battery
internal resistance estimate, average values of measurement, and others.

This patch implements a driver for MAX17042.
In this initial release, we have implemented the most basic features of
a fuel gauge: measure the battery capacity and voltage.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This patch adds a simple driver for chargers indicating their online
status through a GPIO pin.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Add support for the battery voltage measurement part of the JZ4740 ADC unit.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1416/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>