The Bluetooth technology introduces new features on a regular basis
and for some of them it is important that the hardware on both sides
support them. For features like Simple Pairing it is important that
the host stacks on both sides have switched this feature on. To make
valid decisions, a config stage during ACL link establishment has been
introduced that retrieves remote features and if needed also the remote
extended features (known as remote host features) before signalling
this link as connected.

This change introduces full reference counting of incoming and outgoing
ACL links and the Bluetooth core will disconnect both if no owner of it
is present. To better handle interoperability during the pairing phase
the disconnect timeout for incoming connections has been increased to
10 seconds. This is five times more than for outgoing connections.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since the remote Simple Pairing mode is stored together with the
inquiry cache, it makes sense to show it together with the other
information.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Simple Pairing process can only be used if both sides have the
support enabled in the host stack. The current Bluetooth specification
has three ways to detect this support.

If an Extended Inquiry Result has been sent during inquiry then it
is safe to assume that Simple Pairing is enabled. It is not allowed
to enable Extended Inquiry without Simple Pairing. During the remote
name request phase a notification with the remote host supported
features will be sent to indicate Simple Pairing support. Also the
second page of the remote extended features can indicate support for
Simple Pairing.

For all three cases the value of remote Simple Pairing mode is stored
in the inquiry cache for later use.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Simple Pairing feature is optional and needs to be enabled by the
host stack first. The Linux kernel relies on the Bluetooth daemon to
either enable or disable it, but at any time it needs to know the
current state of the Simple Pairing mode. So track any changes made
by external entities and store the current mode in the HCI device
structure.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During the Simple Pairing process the HCI disconnect timer must be
disabled. The way to do this is by holding a reference count of the
HCI connection. The Simple Pairing process on both sides starts with
an IO Capabilities Request and ends with Simple Pairing Complete.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The class of device value can only be retrieved via inquiry or during
an incoming connection request. Outgoing connections can't ask for the
class of device. To compensate for this the value is stored and copied
via the inquiry cache, but currently only updated via inquiry. This
update should also happen during an incoming connection request.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some minor cosmetic cleanups to the HCI event handling to make the
code easier to read and understand.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth specification supports the default link policy settings
on a per host controller basis. For every new connection the link
manager would then use these settings. It is better to use this instead
of bothering the controller on every connection setup to overwrite the
default settings.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The connection packet type can be changed after the connection has been
established and thus needs to be properly tracked to ensure that the
host stack has always correct and valid information about it.

On incoming connections the Bluetooth core switches the supported packet
types to the configured list for this controller. However the usefulness
of this feature has been questioned a lot. The general consent is that
every Bluetooth host stack should enable as many packet types as the
hardware actually supports and leave the decision to the link manager
software running on the Bluetooth chip.

When running on Bluetooth 2.0 or later hardware, don't change the packet
type for incoming connections anymore. This hardware likely supports
Enhanced Data Rate and thus leave it completely up to the link manager
to pick the best packet type.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When trying to establish an eSCO link between two devices then it can
happen that the remote device falls back to a SCO link. Currently this
case is not handled correctly and the message dispatching will break
since it is looking for eSCO packets. So in case the configured link
falls back to SCO overwrite the link type with the correct value.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The authentication status is not communicated to both parties. This is
actually a flaw in the Bluetooth specification. Only the requesting side
really knows if the authentication was successful or not. This piece of
information is however needed on the other side to know if it has to
trigger the authentication procedure or not. Worst case is that both
sides will request authentication at different times, but this should
be avoided since it costs extra time when setting up a new connection.

For Bluetooth encryption it is required to authenticate the link first
and the encryption status is communicated to both sides. So when a link
is switched to encryption it is possible to update the authentication
status since it implies an authenticated link.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth specification allows to enable or disable the encryption
of an ACL link at any time by either the peer or the remote device. If
a L2CAP or RFCOMM connection requested an encrypted link, they will now
disconnect that link if the encryption gets disabled. Higher protocols
that don't care about encryption (like SDP) are not affected.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Recent tests with various Bluetooth headsets have shown that some of
them don't enforce authentication and encryption when connecting. All
of them leave it up to the host stack to enforce it. Non of them should
allow unencrypted connections, but that is how it is. So in case the
link mode settings require authentication and/or encryption it will now
also be enforced on outgoing RFCOMM connections. Previously this was
only done for incoming connections.

This support has a small drawback from a protocol level point of view
since the host stack can't really tell with 100% certainty if a remote
side is already authenticated or not. So if both sides are configured
to enforce authentication it will be requested twice. Most Bluetooth
chips are caching this information and thus no extra authentication
procedure has to be triggered over-the-air, but it can happen.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Getting the remote L2CAP features mask is really important, but doing
this as less intrusive as possible is tricky. To play nice with older
systems and Bluetooth qualification testing, the features mask is now
only retrieved in two specific cases and only once per lifetime of an
ACL link.

When trying to establish a L2CAP connection and the remote features mask
is unknown, the L2CAP information request is sent when the ACL link goes
into connected state. This applies only to outgoing connections and also
only for the connection oriented channels.

The second case is when a connection request has been received. In this
case a connection response with the result pending and the information
request will be send. After receiving an information response or if the
timeout gets triggered, the normal connection setup process with security
setup will be initiated.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To return garbage_args, the accept_stat must be 0, and we must have a
verifier.  So we shouldn't be resetting the write pointer as we reject
the call.

Also, we must add the two placeholder words here regardless of success
of the unwrap, to ensure the output buffer is left in a consistent state
for svcauth_gss_release().

This fixes a BUG() in svcauth_gss.c:svcauth_gss_release().

Thanks to Aime Le Rouzic for bug report, debugging help, and testing.
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Tested-by: NAime Le Rouzic <aime.le-rouzic@bull.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The errno code returned must be negative.

Fixes "RTNETLINK answers: Unknown error 18446744073709551519".
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v1->v2: Use strlcpy() to ensure s[i].name be null-termination.

1. In netdev_boot_setup_add(), a long name will leak.
   ex. : dev=21,0x1234,0x1234,0x2345,eth123456789verylongname.........
2. In netdev_boot_setup_check(), mismatch will happen if s[i].name
   is a substring of dev->name.
   ex. : dev=...eth1 dev=...eth11

[ With feedback from Ben Hutchings. ]
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parameter "needlock" no long exists.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already have a variable, which has the same capability.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Filters need to be destroyed before beginning to destroy classes
since the destination class needs to still be alive to unbind the
filter.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass double tcf_proto pointers to tcf_destroy_chain() to make it
clear the start of the filter list for more consistency.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Lost connections was reported by Thomas Bätzler (running 2.6.25 kernel) on
the netfilter mailing list (see the thread "Weird nat/conntrack Problem
with PASV FTP upload"). He provided tcpdump recordings which helped to
find a long lingering bug in conntrack.

In TCP connection tracking, checking the lower bound of valid ACK could
lead to mark valid packets as INVALID because:

 - We have got a "higher or equal" inequality, but the test checked
   the "higher" condition only; fixed.
 - If the packet contains a SACK option, it could occur that the ACK
   value was before the left edge of our (S)ACK "window": if a previous
   packet from the other party intersected the right edge of the window
   of the receiver, we could move forward the window parameters beyond
   accepting a valid ack. Therefore in this patch we check the rightmost
   SACK edge instead of the ACK value in the lower bound of valid (S)ACK
   test.
Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 77d16f45 ("[IPV6] ROUTE:
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags") intended to pass various
routing lookup hints around RT6_LOOKUP_F_xxx flags, but conversion was
missing for rt6_device_match().
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a missing "!" in a conditional statement which is causing entries to
be skipped when dumping the default IPv6 static label entries.  This can be
demonstrated by running the following:

 # netlabelctl unlbl add default address:::1 \
                                 label:system_u:object_r:unlabeled_t:s0
 # netlabelctl -p unlbl list

... you will notice that the entry for the IPv6 localhost address is not
displayed but does exist (works correctly, causes collisions when attempting
to add duplicate entries, etc.).
Signed-off-by: NPaul Moore <paul.moore@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an SKB cannot be chained to a session, the current code attempts
to "restore" its ip_summed field from lro_mgr->ip_summed. However,
lro_mgr->ip_summed does not hold the original value; in fact, we'd
better not touch skb->ip_summed since it is not modified by the code
in the path leading to a failure to chain it.  Also use a cleaer
comment to the describe the ip_summed field of struct net_lro_mgr.

Issue raised by Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is that while we work w/o the inet_frags.lock even
read-locked the secret rebuild timer may occur (on another CPU, since
BHs are still disabled in the inet_frag_find) and change the rnd seed
for ipv4/6 fragments.

It was caused by my patch fd9e6354
([INET]: Omit double hash calculations in xxx_frag_intern) late 
in the 2.6.24 kernel, so this should probably be queued to -stable.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix some doc comments to match function and attribute names in
net/netlink/attr.c.
Signed-off-by: NJulius Volz <juliusv@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I found another case where we are sending information to userspace
in the wrong HZ scale.  This should have been fixed back in 2.5 :-(

This means an ABI change but as it stands there is no way for an application
like ss to get the right value.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d62733c8
([SCHED]: Qdisc changes and sch_rr added for multiqueue)
added a NET_SCH_RR option that was unused since the code
went unconditionally into sch_prio.
Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note, in the following patch, 'err' is initialized as:

int err = -ENOBUFS;
Signed-off-by: NWANG Cong <wcong@critical-links.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For n:1 'datagram connections' (eg /dev/log), the unix_dgram_sendmsg
routine implements a form of receiver-imposed flow control by
comparing the length of the receive queue of the 'peer socket' with
the max_ack_backlog value stored in the corresponding sock structure,
either blocking the thread which caused the send-routine to be called
or returning EAGAIN. This routine is used by both SOCK_DGRAM and
SOCK_SEQPACKET sockets. The poll-implementation for these socket types
is datagram_poll from core/datagram.c. A socket is deemed to be
writeable by this routine when the memory presently consumed by
datagrams owned by it is less than the configured socket send buffer
size. This is always wrong for PF_UNIX non-stream sockets connected to
server sockets dealing with (potentially) multiple clients if the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an (usual)
application to 'poll for writeability by repeated send request with
O_NONBLOCK set' until it has consumed its time quantum.

The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_recvmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: NRainer Weikusat <rweikusat@mssgmbh.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an skb has nr_frags set to zero but its frag_list is not empty (as
it can happen if software LRO is enabled), and a previous
tcp_read_sock has consumed the linear part of the skb, then
__skb_splice_bits:

(a) incorrectly reports an error and

(b) forgets to update the offset to account for the linear part

Any of the two problems will cause the subsequent __skb_splice_bits
call (the one that handles the frag_list skbs) to either skip data,
or, if the unadjusted offset is greater then the size of the next skb
in the frag_list, make tcp_splice_read loop forever.
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tcp_mem array which contains limits on the total amount of memory
used by TCP sockets is calculated based on nr_all_pages.  On a 32 bits
x86 system, we should base this on the number of lowmem pages.
Signed-off-by: NMiquel van Smoorenburg <miquels@cistron.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an oops in several failure paths in key allocation. This
Oops occurs when freeing a key that has not been linked yet, so the
key->sdata is not set.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement missing EU regulatory domain for mac80211. Based on the
information in IEEE 802.11-2007 (specifically pages 1142, 1143 & 1148)
and ETSI 301 893 (V1.4.1).
With thanks to Johannes Berg.
Signed-off-by: NTony Vroon <tony@linx.net>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rerouting should only happen in LOCAL_OUT, in INPUT its useless
since the packet has already chosen its final destination.

Noticed by Alexey Dobriyan <adobriyan@gmail.com>.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexey Dobriyan <adobriyan@gmail.com> writes:
> Subject: ICMP sockets destruction vs ICMP packets oops

> After icmp_sk_exit() nuked ICMP sockets, we get an interrupt.
> icmp_reply() wants ICMP socket.
>
> Steps to reproduce:
>
> 	launch shell in new netns
> 	move real NIC to netns
> 	setup routing
> 	ping -i 0
> 	exit from shell
>
> BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
> IP: [<ffffffff803fce17>] icmp_sk+0x17/0x30
> PGD 17f3cd067 PUD 17f3ce067 PMD 0 
> Oops: 0000 [1] PREEMPT SMP DEBUG_PAGEALLOC
> CPU 0 
> Modules linked in: usblp usbcore
> Pid: 0, comm: swapper Not tainted 2.6.26-rc6-netns-ct #4
> RIP: 0010:[<ffffffff803fce17>]  [<ffffffff803fce17>] icmp_sk+0x17/0x30
> RSP: 0018:ffffffff8057fc30  EFLAGS: 00010286
> RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff81017c7db900
> RDX: 0000000000000034 RSI: ffff81017c7db900 RDI: ffff81017dc41800
> RBP: ffffffff8057fc40 R08: 0000000000000001 R09: 000000000000a815
> R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff8057fd28
> R13: ffffffff8057fd00 R14: ffff81017c7db938 R15: ffff81017dc41800
> FS:  0000000000000000(0000) GS:ffffffff80525000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
> CR2: 0000000000000000 CR3: 000000017fcda000 CR4: 00000000000006e0
> DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
> DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
> Process swapper (pid: 0, threadinfo ffffffff8053a000, task ffffffff804fa4a0)
> Stack:  0000000000000000 ffff81017c7db900 ffffffff8057fcf0 ffffffff803fcfe4
>  ffffffff804faa38 0000000000000246 0000000000005a40 0000000000000246
>  000000000001ffff ffff81017dd68dc0 0000000000005a40 0000000055342436
> Call Trace:
>  <IRQ>  [<ffffffff803fcfe4>] icmp_reply+0x44/0x1e0
>  [<ffffffff803d3a0a>] ? ip_route_input+0x23a/0x1360
>  [<ffffffff803fd645>] icmp_echo+0x65/0x70
>  [<ffffffff803fd300>] icmp_rcv+0x180/0x1b0
>  [<ffffffff803d6d84>] ip_local_deliver+0xf4/0x1f0
>  [<ffffffff803d71bb>] ip_rcv+0x33b/0x650
>  [<ffffffff803bb16a>] netif_receive_skb+0x27a/0x340
>  [<ffffffff803be57d>] process_backlog+0x9d/0x100
>  [<ffffffff803bdd4d>] net_rx_action+0x18d/0x250
>  [<ffffffff80237be5>] __do_softirq+0x75/0x100
>  [<ffffffff8020c97c>] call_softirq+0x1c/0x30
>  [<ffffffff8020f085>] do_softirq+0x65/0xa0
>  [<ffffffff80237af7>] irq_exit+0x97/0xa0
>  [<ffffffff8020f198>] do_IRQ+0xa8/0x130
>  [<ffffffff80212ee0>] ? mwait_idle+0x0/0x60
>  [<ffffffff8020bc46>] ret_from_intr+0x0/0xf
>  <EOI>  [<ffffffff80212f2c>] ? mwait_idle+0x4c/0x60
>  [<ffffffff80212f23>] ? mwait_idle+0x43/0x60
>  [<ffffffff8020a217>] ? cpu_idle+0x57/0xa0
>  [<ffffffff8040f380>] ? rest_init+0x70/0x80
> Code: 10 5b 41 5c 41 5d 41 5e c9 c3 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 53
> 48 83 ec 08 48 8b 9f 78 01 00 00 e8 2b c7 f1 ff 89 c0 <48> 8b 04 c3 48 83 c4 08
> 5b c9 c3 66 66 66 66 66 2e 0f 1f 84 00
> RIP  [<ffffffff803fce17>] icmp_sk+0x17/0x30
>  RSP <ffffffff8057fc30>
> CR2: 0000000000000000
> ---[ end trace ea161157b76b33e8 ]---
> Kernel panic - not syncing: Aiee, killing interrupt handler!

Receiving packets while we are cleaning up a network namespace is a
racy proposition. It is possible when the packet arrives that we have
removed some but not all of the state we need to fully process it.  We
have the choice of either playing wack-a-mole with the cleanup routines
or simply dropping packets when we don't have a network namespace to
handle them.

Since the check looks inexpensive in netif_receive_skb let's just
drop the incoming packets.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Gabriel Campana, the kmalloc() length arg
passed in by sctp_getsockopt_local_addrs_old() can overflow
if ->addr_num is large enough.

Therefore, enforce an appropriate limit.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>