Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 23 3月, 2018 5 次提交
    • P
      powerpc/powernv: Provide a way to force a core into SMT4 mode · 7672691a
      由 Paul Mackerras 提交于 
      POWER9 processors up to and including "Nimbus" v2.2 have hardware
bugs relating to transactional memory and thread reconfiguration.
One of these bugs has a workaround which is to get the core into
SMT4 state temporarily.  This workaround is only needed when
running bare-metal.

This patch provides a function which gets the core into SMT4 mode
by preventing threads from going to a stop state, and waking up
those which are already in a stop state.  Once at least 3 threads
are not in a stop state, the core will be in SMT4 and we can
continue.

To do this, we add a "dont_stop" flag to the paca to tell the
thread not to go into a stop state.  If this flag is set,
power9_idle_stop() just returns immediately with a return value
of 0.  The pnv_power9_force_smt4_catch() function does the following:

1. Set the dont_stop flag for each thread in the core, except
   ourselves (in fact we use an atomic_inc() in case more than
   one thread is calling this function concurrently).
2. See how many threads are awake, indicated by their
   requested_psscr field in the paca being 0.  If this is at
   least 3, skip to step 5.
3. Send a doorbell interrupt to each thread that was seen as
   being in a stop state in step 2.
4. Until at least 3 threads are awake, scan the threads to which
   we sent a doorbell interrupt and check if they are awake now.

This relies on the following properties:

- Once dont_stop is non-zero, requested_psccr can't go from zero to
  non-zero, except transiently (and without the thread doing stop).
- requested_psscr being zero guarantees that the thread isn't in
  a state-losing stop state where thread reconfiguration could occur.
- Doing stop with a PSSCR value of 0 won't be a state-losing stop
  and thus won't allow thread reconfiguration.
- Once threads_per_core/2 + 1 (i.e. 3) threads are awake, the core
  must be in SMT4 mode, since SMT modes are powers of 2.

This does add a sync to power9_idle_stop(), which is necessary to
provide the correct ordering between setting requested_psscr and
checking dont_stop.  The overhead of the sync should be unnoticeable
compared to the latency of going into and out of a stop state.

Because some objected to incurring this extra latency on systems where
the XER[SO] bug is not relevant, I have put the test in
power9_idle_stop inside a feature section.  This means that
pnv_power9_force_smt4_catch() WILL NOT WORK correctly on systems
without the CPU_FTR_P9_TM_XER_SO_BUG feature bit set, and will
probably hang the system.

In order to cater for uses where the caller has an operation that
has to be done while the core is in SMT4, the core continues to be
kept in SMT4 after pnv_power9_force_smt4_catch() function returns,
until the pnv_power9_force_smt4_release() function is called.
It undoes the effect of step 1 above and allows the other threads
to go into a stop state.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      7672691a
    • P
      powerpc: Add CPU feature bits for TM bug workarounds on POWER9 v2.2 · b5af4f27
      由 Paul Mackerras 提交于 
      This adds a CPU feature bit which is set for POWER9 "Nimbus" DD2.2
processors which will be used to enable the hypervisor to assist
hardware with the handling of checkpointed register values while the
CPU is in suspend state, in order to work around hardware bugs.  The
hardware assistance for these workarounds introduced a new hardware
bug relating to the XER[SO] bit.  We add a separate feature bit for
this bug in case future chips fix it while still requiring the
hypervisor assistance with suspend state.

When the dt_cpu_ftrs subsystem is in use, the software assistance can
be enabled using a "tm-suspend-hypervisor-assist" node in the device
tree, and a "tm-suspend-xer-so-bug" node enables the workarounds for
the XER[SO] bug.  In the absence of such nodes, a quirk enables both
for POWER9 "Nimbus" DD2.2 processors.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      b5af4f27
    • P
      powerpc: Free up CPU feature bits on 64-bit machines · 9bbf0b57
      由 Paul Mackerras 提交于 
      This moves all the CPU feature bits that are only used on 32-bit
machines to the top 20 bits of the CPU feature word and arranges
for them to be defined only in 32-bit builds.  The features that
are common to 32-bit and 64-bit machines are moved to bits 0-11
of the CPU feature word.  This means that for 64-bit platforms,
bits 44-63 can now be used for new features that only exist on
64-bit machines.  (These bit numbers are counting from the right,
i.e. the LSB is bit 0.)

Because CPU_FTR_L3_DISABLE_NAP moved from the low 16 bits to the high
16 bits, we have to adjust some assembly code.  Also, CPU_FTR_EMB_HV
moved from the high 16 bits to the low 16 bits.

Note that CPU_FTR_REAL_LE only applies to 64-bit chips, because only
64-bit chips (POWER6, 7, 8, 9) have a true little-endian mode that is
a CPU execution mode as opposed to being a page attribute.

With this we now have 20 free CPU feature bits on 64-bit machines.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      9bbf0b57
    • P
      powerpc: Book E: Remove unused CPU_FTR_L2CSR bit · dd0efb3f
      由 Paul Mackerras 提交于 
      The CPU_FTR_L2CSR bit is never tested anywhere, so let's reclaim the
bit.

The last usage was removed in 86d63363 ("powerpc/e500mc: Remove
dead L2 flushing code in idle_e500.S") (Jun 2015).
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      dd0efb3f
    • P
      powerpc: Use feature bit for RTC presence rather than timebase presence · c0d64cf9
      由 Paul Mackerras 提交于 
      All PowerPC CPUs other than the original PPC601 have a timebase
register rather than the "real-time clock" (RTC) register that the
PPC601 (and the original POWER and POWER2 CPUs) had.  Currently
we have a CPU feature bit to indicate the presence of the timebase,
but it makes more sense to use a bit to indicate the unusual
situation rather than the common situation.  This therefore defines
a CPU_FTR_USE_RTC bit in place of the CPU_FTR_USE_TB bit, and
arranges for it to be set on PPC601 systems.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      c0d64cf9
  3. 12 2月, 2018 3 次提交
    • A
      unify {de,}mangle_poll(), get rid of kernel-side POLL... · 7a163b21
      由 Al Viro 提交于 
      except, again, POLLFREE and POLL_BUSY_LOOP.

With this, we finally get to the promised end result:

 - POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
   stray instances of ->poll() still using those will be caught by
   sparse.

 - eventpoll.c and select.c warning-free wrt __poll_t

 - no more kernel-side definitions of POLL... - userland ones are
   visible through the entire kernel (and used pretty much only for
   mangle/demangle)

 - same behavior as after the first series (i.e. sparc et.al. epoll(2)
   working correctly).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      7a163b21
    • L
      vfs: do bulk POLL* -> EPOLL* replacement · a9a08845
      由 Linus Torvalds 提交于 
      This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      a9a08845
    • M
      xtensa: fix build with KASAN · f8d0cbf2
      由 Max Filippov 提交于 
      The commit 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT
usage") removed KASAN_SHADOW_SCALE_SHIFT definition from
include/linux/kasan.h and added it to architecture-specific headers,
except for xtensa. This broke the xtensa build with KASAN enabled.
Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h

Reported by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage")
Acked-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
      f8d0cbf2
  5. 11 2月, 2018 3 次提交
  7. 10 2月, 2018 1 次提交
  9. 09 2月, 2018 4 次提交
    • J
      KVM: PPC: Book3S: Add MMIO emulation for VMX instructions · 09f98496
      由 Jose Ricardo Ziviani 提交于 
      This patch provides the MMIO load/store vector indexed
X-Form emulation.

Instructions implemented:
lvx: the quadword in storage addressed by the result of EA &
0xffff_ffff_ffff_fff0 is loaded into VRT.

stvx: the contents of VRS are stored into the quadword in storage
addressed by the result of EA & 0xffff_ffff_ffff_fff0.
Reported-by: NGopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Reported-by: NBalamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: NJose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
      09f98496
    • A
      KVM: PPC: Book3S HV: Branch inside feature section · d20fe50a
      由 Alexander Graf 提交于 
      We ended up with code that did a conditional branch inside a feature
section to code outside of the feature section. Depending on how the
object file gets organized, that might mean we exceed the 14bit
relocation limit for conditional branches:

  arch/powerpc/kvm/built-in.o:arch/powerpc/kvm/book3s_hv_rmhandlers.S:416:(__ftr_alt_97+0x8): relocation truncated to fit: R_PPC64_REL14 against `.text'+1ca4

So instead of doing a conditional branch outside of the feature section,
let's just jump at the end of the same, making the branch very short.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
      d20fe50a
    • D
      KVM: PPC: Book3S HV: Make HPT resizing work on POWER9 · 790a9df5
      由 David Gibson 提交于 
      This adds code to enable the HPT resizing code to work on POWER9,
which uses a slightly modified HPT entry format compared to POWER8.
On POWER9, we convert HPTEs read from the HPT from the new format to
the old format so that the rest of the HPT resizing code can work as
before.  HPTEs written to the new HPT are converted to the new format
as the last step before writing them into the new HPT.

This takes out the checks added by commit bcd3bb63 ("KVM: PPC:
Book3S HV: Disable HPT resizing on POWER9 for now", 2017-02-18),
now that HPT resizing works on POWER9.

On POWER9, when we pivot to the new HPT, we now call
kvmppc_setup_partition_table() to update the partition table in order
to make the hardware use the new HPT.

[paulus@ozlabs.org - added kvmppc_setup_partition_table() call,
 wrote commit message.]
Tested-by: NLaurent Vivier <lvivier@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
      790a9df5
    • P
      KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code · 05f2bb03
      由 Paul Mackerras 提交于 
      This fixes the computation of the HPTE index to use when the HPT
resizing code encounters a bolted HPTE which is stored in its
secondary HPTE group.  The code inverts the HPTE group number, which
is correct, but doesn't then mask it with new_hash_mask.  As a result,
new_pteg will be effectively negative, resulting in new_hptep
pointing before the new HPT, which will corrupt memory.

In addition, this removes two BUG_ON statements.  The condition that
the BUG_ONs were testing -- that we have computed the hash value
incorrectly -- has never been observed in testing, and if it did
occur, would only affect the guest, not the host.  Given that
BUG_ON should only be used in conditions where the kernel (i.e.
the host kernel, in this case) can't possibly continue execution,
it is not appropriate here.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
      05f2bb03
  11. 08 2月, 2018 4 次提交
  13. 07 2月, 2018 20 次提交