There are a bunch of callsite where the ssk socket
lock is acquired using the full-blown version eligible for
the fast variant. Let's move to the latter.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mentioned cache was introduced to reduce the number of skb
allocation in atomic context, but the required complexity is
excessive.

This change remove the mentioned cache.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcin Wojtas says:

====================
ACPI MDIO support for Marvell controllers

The third version of the patchset main change is
dropping a clock handling optimisation patch
for mvmdio driver. Other than that it sets
explicit dependency on FWNODE_MDIO for CONFIG_FSL_XGMAC_MDIO
and applies minor cosmetic improvements (please see the
'Changelog' below).

The firmware ACPI description is exposed in the public github branch:
https://github.com/semihalf-wojtas-marcin/edk2-platforms/commits/acpi-mdio-r20210613
There is also MacchiatoBin firmware binary available for testing:
https://drive.google.com/file/d/1eigP_aeM4wYQpEaLAlQzs3IN_w1-kQr0

I'm looking forward to the comments or remarks.

Best regards,
Marcin

Changelog:
v2->v3
* Rebase on top of net-next/master.
* Drop "net: mvmdio: simplify clock handling" patch.
* 1/6 - fix code block comments.
* 2/6 - unchanged
* 3/6 - add "depends on FWNODE_MDIO" for CONFIG_FSL_XGMAC_MDIO
* 4/6 - drop mention about the clocks from the commit message.
* 5/6 - unchanged
* 6/6 - add Andrew's RB.

v1->v2
* 1/7 - new patch
* 2/7 - new patch
* 3/7 - new patch
* 4/7 - new patch
* 5/7 - remove unnecessary `if (has_acpi_companion())` and rebase onto
        the new clock handling
* 6/7 - remove deprecated comment
* 7/7 - no changes
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'has_phy' field from struct mvpp2_port is no longer used.
Remove it.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the MDIO and phylink are supported in the ACPI
world, enable to use them in the mvpp2 driver. Ensure a backward
compatibility with the firmware whose ACPI description does
not contain the necessary elements for the proper phy handling
and fall back to relying on the link interrupts instead.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introducing ACPI support for the mvmdio driver by adding
acpi_match_table with two entries:

* "MRVL0100" for the SMI operation
* "MRVL0101" for the XSMI mode
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize the newly added helper routine
for registering the MDIO bus via fwnode_
interface.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a new helper function that
wraps acpi_/of_ mdiobus_register() and allows its
usage via common fwnode_ interface.

Fall back to raw mdiobus_register() in case CONFIG_FWNODE_MDIO
is not enabled, in order to satisfy compatibility
in all future user drivers.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Document additional MAC configuration modes which can be processed
by the existing fwnode_ phylink helpers:

* "managed" standard ACPI _DSD property [1]
* "fixed-link" data-only subnode linked in the _DSD package via
  generic mechanism of the hierarchical data extension [2]

[1] https://www.uefi.org/sites/default/files/resources/_DSD-device-properties-UUID.pdf
[2] https://github.com/UEFI/DSD-Guide/blob/main/dsd-guide.pdfSigned-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the_virtio_vsock is not NULL before dereferencing it.

general protection fault, probably for non-canonical address 0xdffffc0000000071: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000388-0x000000000000038f]
CPU: 0 PID: 8452 Comm: syz-executor406 Not tainted 5.13.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:virtio_transport_seqpacket_allow+0xbf/0x210 net/vmw_vsock/virtio_transport.c:503
Code: e8 c6 d9 ab f8 84 db 0f 84 0f 01 00 00 e8 09 d3 ab f8 48 8d bd 88 03 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 06 0f 8e 2a 01 00 00 44 0f b6 a5 88 03 00 00
RSP: 0018:ffffc90003757c18 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000071 RSI: ffffffff88c908e7 RDI: 0000000000000388
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff88c90a06 R11: 0000000000000000 R12: 0000000000000000
R13: ffffffff88c90840 R14: 0000000000000000 R15: 0000000000000001
FS:  0000000001bee300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000082 CR3: 000000002847e000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 vsock_assign_transport+0x575/0x700 net/vmw_vsock/af_vsock.c:490
 vsock_connect+0x200/0xc00 net/vmw_vsock/af_vsock.c:1337
 __sys_connect_file+0x155/0x1a0 net/socket.c:1824
 __sys_connect+0x161/0x190 net/socket.c:1841
 __do_sys_connect net/socket.c:1851 [inline]
 __se_sys_connect net/socket.c:1848 [inline]
 __x64_sys_connect+0x6f/0xb0 net/socket.c:1848
 do_syscall_64+0x3a/0xb0 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x43ee69
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd49e7c788 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000400488 RCX: 000000000043ee69
RDX: 0000000000000010 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 0000000000402e50 R08: 0000000000000000 R09: 0000000000400488
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000402ee0
R13: 0000000000000000 R14: 00000000004ac018 R15: 0000000000400488

Fixes: 53efbba1 ("virtio/vsock: enable SEQPACKET for transport")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Reviewed-by: NStefano Garzarella <sgarzare@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since these strings are expected to be NUL-terminated and the buffers
are exactly sized (in vnic_client_data_len()) with no padding, strncpy()
can be safely replaced with strscpy() here, as strncpy() on
NUL-terminated string is considered deprecated[1]. This has the
side-effect of silencing a -Warray-bounds warning due to the compiler
being confused about the vlcd incrementing:

In file included from ./include/linux/string.h:253,
                 from ./include/linux/bitmap.h:10,
                 from ./include/linux/cpumask.h:12,
                 from ./include/linux/mm_types_task.h:14,
                 from ./include/linux/mm_types.h:5,
                 from ./include/linux/buildid.h:5,
                 from ./include/linux/module.h:14,
                 from drivers/net/ethernet/ibm/ibmvnic.c:35:
In function '__fortify_strncpy',
    inlined from 'vnic_add_client_data' at drivers/net/ethernet/ibm/ibmvnic.c:3919:2:
./include/linux/fortify-string.h:39:30: warning: '__builtin_strncpy' offset 12 from the object at 'v
lcd' is out of the bounds of referenced subobject 'name' with type 'char[]' at offset 12 [-Warray-bo
unds]
   39 | #define __underlying_strncpy __builtin_strncpy
      |                              ^
./include/linux/fortify-string.h:51:9: note: in expansion of macro '__underlying_strncpy'
   51 |  return __underlying_strncpy(p, q, size);
      |         ^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ibm/ibmvnic.c: In function 'vnic_add_client_data':
drivers/net/ethernet/ibm/ibmvnic.c:3883:7: note: subobject 'name' declared here
 3883 |  char name[];
      |       ^~~~

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings

Cc: Dany Madden <drt@linux.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Cc: Thomas Falcon <tlfalcon@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to commit 3b707c30 ("net: dev_is_mac_header_xmit() true for
ARPHRD_RAWIP"), add ARPHRD_IP6GRE to dev_is_mac_header_xmit(), to make
ip6gre compatible with act_mirred and __bpf_redirect().
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 0dca2c74.

The commit in question breaks hardware offload of flower filters.

Quoting Vladimir Oltean <olteanv@gmail.com>:

 fl_hw_replace_filter() and fl_reoffload() create a struct
 flow_cls_offload with a rule->match.mask member derived from the mask
 of the software classifier: &f->mask->key - that same mask that is used
 for initializing the flow dissector keys, and the one from which Boris
 removed the basic.n_proto member because it was bothering him.
Reported-by: NVadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: NBoris Sukholitko <boris.sukholitko@broadcom.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: f6396341 ("net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY")
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify the pr_info content from int to char * in sock_register() and
sock_unregister(), this looks more readable.

Fixed build error in ARCH=sparc64.
Signed-off-by: NYejune Deng <yejune.deng@gmail.com>
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Zhou Yanjie says:

====================
Fix for Ingenic MAC support.

1.Remove the unexpected "snps,dwmac" item in the example.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the unexpected "snps,dwmac" item in the example.

Fixes: 3b840106 ("dt-bindings: dwmac: Add bindings for new Ingenic SoCs.")
Signed-off-by: N周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If this 'kzalloc()' fails we must free some resources as in all the other
error handling paths of this function.

Fixes: 2e2deee7 ("net: hns3: add the RAS compatibility adaptation solution")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joakim Zhang says:

====================
net: fec: fix TX bandwidth fluctuations

This patch set intends to fix TX bandwidth fluctuations, any feedback would be appreciated.

---
ChangeLogs:
	V1: remove RFC tag, RFC discussions please turn to below:
	    https://lore.kernel.org/lkml/YK0Ce5YxR2WYbrAo@lunn.ch/T/
	V2: change functions to be static in this patch set. And add the
	t-b tag.
	V3: fix sparse warining: ntohs()->htons()
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we know that AVB is enabled by default, and the ENET IP design is
queue 0 for best effort, queue 1&2 for AVB Class A&B. Bandwidth of each
queue 1&2 set in driver is 50%, TX bandwidth fluctuated when selecting
tx queues randomly with FEC_QUIRK_HAS_AVB quirk available.

This patch adds ndo_select_queue callback to select queues for
transmitting to fix this issue. It will always return queue 0 if this is
not a vlan packet, and return queue 1 or 2 based on priority of vlan
packet.

You may complain that in fact we only use single queue for trasmitting
if we are not targeted to VLAN. Yes, but seems we have no choice, since
AVB is enabled when the driver probed, we can't switch this feature
dynamicly. After compare multiple queues to single queue, TX throughput
almost no improvement.

One way we can implemet is to configure the driver to multiple queues
with Round-robin scheme by default. Then add ndo_setup_tc callback to
enable/disable AVB feature for users. Unfortunately, ENET AVB IP seems
not follow the standard 802.1Qav spec. We only can program
DMAnCFG[IDLE_SLOPE] field to calculate bandwidth fraction. And idle
slope is restricted to certain valus (a total of 19). It's far away from
CBS QDisc implemented in Linux TC framework. If you strongly suggest to do
this, I think we only can support limited numbers of bandwidth and reject
others, but it's really urgly and wried.

With this patch, VLAN tagged packets route to queue 0/1/2 based on vlan
priority; VLAN untagged packets route to queue 0.
Tested-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frieder Schrempf reported a TX throuthput issue [1], it happens quite often
that the measured bandwidth in TX direction drops from its expected/nominal
value to something like ~50% (for 100M) or ~67% (for 1G) connections.

[1] https://lore.kernel.org/linux-arm-kernel/421cc86c-b66f-b372-32f7-21e59f9a98bc@kontron.de/

The issue becomes clear after digging into it, Net core would select
queues when transmitting packets. Since FEC have not impletemented
ndo_select_queue callback yet, so it will call netdev_pick_tx to select
queues randomly.

For i.MX6SX ENET IP with AVB support, driver default enables this
feature. According to the setting of QOS/RCMRn/DMAnCFG registers, AVB
configured to Credit-based scheme, 50% bandwidth of each queue 1&2.

With below tests let me think more:
1) With FEC_QUIRK_HAS_AVB quirk, can reproduce TX bandwidth fluctuations issue.
2) Without FEC_QUIRK_HAS_AVB quirk, can't reproduce TX bandwidth fluctuations issue.

The related difference with or w/o FEC_QUIRK_HAS_AVB quirk is that, whether we
program FTYPE field of TxBD or not. As I describe above, AVB feature is
enabled by default. With FEC_QUIRK_HAS_AVB quirk, frames in queue 0
marked as non-AVB, and frames in queue 1&2 marked as AVB Class A&B. It's
unreasonable if frames in queue 1&2 are not required to be time-sensitive.
So when Net core select tx queues ramdomly, Credit-based scheme would work
and lead to TX bandwidth fluctuated. On the other hand, w/o
FEC_QUIRK_HAS_AVB quirk, frames in queue 1&2 are all marked as non-AVB, so
Credit-based scheme would not work.

Till now, how can we fix this TX throughput issue? Yes, please remove
FEC_QUIRK_HAS_AVB quirk if you suffer it from time-nonsensitive networking.
However, this quirk is used to indicate i.MX6SX, other setting depends
on it. So this patch adds a new quirk FEC_QUIRK_HAS_MULTI_QUEUES to
represent i.MX6SX, it is safe for us remove FEC_QUIRK_HAS_AVB quirk
now.

FEC_QUIRK_HAS_AVB quirk is set by default in the driver, and users may
not know much about driver details, they would waste effort to find the
root cause, that is not we want. The following patch is a implementation
to fix it and users don't need to modify the driver.
Tested-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Improvement for DSA cross-chip setups

This series improves some aspects in multi-switch DSA tree topologies:
- better device tree validation
- better handling of MTU changes
- better handling of multicast addresses
- removal of some unused code
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With MRP hardware assist being supported only by the ocelot switch
family, which by design does not support cross-chip bridging, the
current match functions are at best a guess and have not been confirmed
in any way to do anything relevant in a multi-switch topology.

Drop the code and make the notifiers match only on the targeted switch
port.

Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dsa_slave_change_mtu() calls dsa_port_mtu_change() twice:
- it sends a cross-chip notifier with the MTU of the CPU port which is
  used to update the DSA links.
- it sends one targeted MTU notifier which is supposed to only match the
  user port on which we are changing the MTU. The "propagate_upstream"
  variable is used here to bypass the cross-chip notifier system from
  switch.c

But due to a mistake, the second, targeted notifier matches not only on
the user port, but also on the DSA link which is a member of the same
switch, if that exists.

And because the DSA links of the entire dst were programmed in a
previous round to the largest_mtu via a "propagate_upstream == true"
notification, then the dsa_port_mtu_change(propagate_upstream == false)
call that is immediately upcoming will break the MTU on the one DSA link
which is chip-wise local to the dp whose MTU is changing right now.

Example given this daisy chain topology:

   sw0p0     sw0p1     sw0p2     sw0p3     sw0p4
[  cpu  ] [  user ] [  user ] [  dsa  ] [  user ]
[   x   ] [       ] [       ] [   x   ] [       ]
                                  |
                                  +---------+
                                            |
   sw1p0     sw1p1     sw1p2     sw1p3     sw1p4
[  user ] [  user ] [  user ] [  dsa  ] [  dsa  ]
[       ] [       ] [       ] [       ] [   x   ]

ip link set sw0p1 mtu 9000
ip link set sw1p1 mtu 9000 # at this stage, sw0p1 and sw1p1 can talk
                           # to one another using jumbo frames
ip link set sw0p2 mtu 1500 # this programs the sw0p3 DSA link first to
                           # the largest_mtu of 9000, then reprograms it to
                           # 1500 with the "propagate_upstream == false"
                           # notifier, breaking communication between
                           # sw0p1 and sw1p1

To escape from this situation, make the targeted match really match on a
single port - the user port, and rename the "propagate_upstream"
variable to "targeted_match" to clarify the intention and avoid future
issues.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we have a cross-chip topology like this:

   sw0p0     sw0p1     sw0p2     sw0p3     sw0p4
[  cpu  ] [  user ] [  user ] [  dsa  ] [  user ]
                                  |
                                  +---------+
                                            |
   sw1p0     sw1p1     sw1p2     sw1p3     sw1p4
[  user ] [  user ] [  user ] [  dsa  ] [  dsa  ]

and we issue the following commands:

1. ip link set sw0p1 mtu 1700
2. ip link set sw1p1 mtu 1600

we notice the following happening:

Command 1. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 0, of 1700. This matches
sw0p0, sw0p3 and sw1p4 (all CPU ports and DSA links).
Then, it emits a targeted MTU notifier for the user port (sw0p1), again
with MTU 1700 (this doesn't matter).

Command 2. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 1, of 1600. This matches
the same group of ports as above, and decreases the MTU for the CPU port
and the DSA links from 1700 to 1600.

As a result, the sw0p1 user port can no longer communicate with its CPU
port at MTU 1700.

To address this, we should calculate the largest_mtu across all switches
that may share a CPU port, and only emit MTU notifiers with that value.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the notifier for adding a multicast MAC address matches on
the targeted port and on all DSA links in the system, be they upstream
or downstream links.

This leads to a considerable amount of useless traffic.

Consider this daisy chain topology, and a MDB add notifier emitted on
sw0p0. It matches on sw0p0, sw0p3, sw1p3 and sw2p4.

   sw0p0     sw0p1     sw0p2     sw0p3     sw0p4
[  user ] [  user ] [  user ] [  dsa  ] [  cpu  ]
[   x   ] [       ] [       ] [   x   ] [       ]
                                  |
                                  +---------+
                                            |
   sw1p0     sw1p1     sw1p2     sw1p3     sw1p4
[  user ] [  user ] [  user ] [  dsa  ] [  dsa  ]
[       ] [       ] [       ] [   x   ] [   x   ]
                                  |
                                  +---------+
                                            |
   sw2p0     sw2p1     sw2p2     sw2p3     sw2p4
[  user ] [  user ] [  user ] [  user ] [  dsa  ]
[       ] [       ] [       ] [       ] [   x   ]

But switch 0 has no reason to send the multicast traffic for that MAC
address on sw0p3, which is how it reaches switches 1 and 2. Those
switches don't expect, according to the user configuration, to receive
this multicast address from switch 1, and they will drop it anyway,
because the only valid destination is the port they received it on.
They only need to configure themselves to deliver that multicast address
_towards_ switch 1, where the MDB entry is installed.

Similarly, switch 1 should not send this multicast traffic towards
sw1p3, because that is how it reaches switch 2.

With this change, the heat map for this MDB notifier changes as follows:

   sw0p0     sw0p1     sw0p2     sw0p3     sw0p4
[  user ] [  user ] [  user ] [  dsa  ] [  cpu  ]
[   x   ] [       ] [       ] [       ] [       ]
                                  |
                                  +---------+
                                            |
   sw1p0     sw1p1     sw1p2     sw1p3     sw1p4
[  user ] [  user ] [  user ] [  dsa  ] [  dsa  ]
[       ] [       ] [       ] [       ] [   x   ]
                                  |
                                  +---------+
                                            |
   sw2p0     sw2p1     sw2p2     sw2p3     sw2p4
[  user ] [  user ] [  user ] [  user ] [  dsa  ]
[       ] [       ] [       ] [       ] [   x   ]

Now the mdb notifier behaves the same as the fdb notifier.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The difference between dsa_is_user_port and dsa_port_is_user is that the
former needs to look up the list of ports of the DSA switch tree in
order to find the struct dsa_port, while the latter directly receives it
as an argument.

dsa_is_user_port is already in widespread use and has its place, so
there isn't any chance of converting all callers to a single form.
But being able to do:
	dsa_port_is_user(dp)
instead of
	dsa_is_user_port(dp->ds, dp->index)

is much more efficient too, especially when the "dp" comes from an
iterator over the DSA switch tree - this reduces the complexity from
quadratic to linear.

Move these helpers from dsa2.c to include/net/dsa.h so that others can
use them too.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cross-chip notifiers work by comparing each ds->index against the
info->sw_index value from the notifier. The ds->index is retrieved from
the device tree dsa,member property.

If a single tree cross-chip topology does not declare unique switch IDs,
this will result in hard-to-debug issues/voodoo effects such as the
cross-chip notifier for one switch port also matching the port with the
same number from another switch.

Check in dsa_switch_parse_member_of() whether the DSA switch tree
contains a DSA switch with the index we're preparing to add, before
actually adding it.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the chackpatch.pl, no space before tabs.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the chackpatch.pl, comparison to NULL could
be written "!card".
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add support for module EEPROM read by page

Add support for ethtool_ops::get_module_eeprom_by_page() operation.

Patch #1 adds necessary field in device register.

Patch #2 documents possible MCIA status values so that more meaningful
error messages could be returned to user space via extack.

Patch #3 adds the actual implementation.
===================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for ethtool_ops::get_module_eeprom_by_page() which allows
user space to read transceiver module EEPROM based on passed parameters.

The I2C address is not validated in order to avoid module-specific code.
In case of wrong address, error will be returned from device's firmware.

Tested by comparing output with legacy method (ioctl) output.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Tested-by: NVadim Pasternak <vadimp@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Will be used to emit meaningful messages to user space via extack in a
subsequent patch.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add bank number to MCIA (Management Cable Info Access) register in order
to allow access to banked pages on EEPROMs using CMIS (Common Management
Interface Specification) memory map.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: add support for IPA v3.1

This series adds support for IPA v3.1, used by the Qualcomm
Snapdragon 835 (MSM8998).

The first patch adds "qcom,msm8998-ipa" to the DT binding.

The next four patches add code to ensure correct operation on
IPA v3.1:
  - Avoid touching unsupported inter-EE interrupt mask registers
  - Set the proper flags in the clock configuration register
  - Work around the lack of an IPA FLAVOR_0 register
  - Work around the lack of a GSI PARAM_2 register

The last patch defines configuration data for this version of IPA.

Many thanks are due to AngeloGioacchino Del Regno and Jami Kettunen,
both associated with SoMainline.  Angelo first posted code to
implement most of what was required for this, and Jami has been
helpful testing these changes on his hardware.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the MSM8998 SoC, which includes IPA version 3.1.

Originally proposed by AngeloGioacchino Del Regno.

Link: https://lore.kernel.org/netdev/20210211175015.200772-6-angelogioacchino.delregno@somainline.orgSigned-off-by: NAlex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to IPA v3.5.1, there is no HW_PARAM_2 GSI register, which we
use to determine the number of channels and endpoints per execution
environment.  In that case, we will just assume the number supported
is the maximum supported by the driver.

Introduce gsi_ring_setup() to encapsulate the code that determines
the number of channels and endpoints.

Update GSI_EVT_RING_COUNT_MAX so it is big enough to handle any
available channel for all supported hardware (IPA v4.9 can have 23
channels and 24 event rings).
Signed-off-by: NAlex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FLAVOR_0 version first appears in IPA v3.5, so avoid attempting
to read it for versions prior to that.

This register contains a concise definition of the number and
direction of endpoints supported by the hardware, and without it
we can't verify endpoint configuration in ipa_endpoint_config().
In this case, just indicate that any endpoint number is available
for use.

Originally proposed by AngeloGioacchino Del Regno.

Link: https://lore.kernel.org/netdev/20210211175015.200772-3-angelogioacchino.delregno@somainline.orgSigned-off-by: NAlex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For IPA v3.1, a workaround is needed to disable gating on a MISC
clock.  I have no further explanation, but this is what the
downstream code (msm-4.4) does.

This was suggested in a patch from AngeloGioacchino Del Regno.

Link: https://lore.kernel.org/netdev/20210211175015.200772-2-angelogioacchino.delregno@somainline.orgSigned-off-by: NAlex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: NDavid S. Miller <davem@davemloft.net>