A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.

As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.

This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: NPierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Export phy_mii_ioctl, so network drivers can use it when built
as modules too.
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for new Myri-10G boards with PCI device id 9.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] cpu-bugs64.c: GCC 3.3 constraint workaround
  [MIPS] DEC: Initialise ioasic_ssr_lock

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (6173a): Documentation: Remove reference to dead "cpia_pp=" boot-time option
  Revert "V4L/DVB (6173a): Documentation: Remove reference to dead "cpia_pp=" boot-time option"

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] Avoid replaying inode buffer initialisation log items if on-disk version is newer.
  [XFS] Ensure file size updates have been completed before writing inode to disk.
  [XFS] On-demand reaping of the MRU cache

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SUNSAB]: Fix several bugs.

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: remove unused variables from drivers/ide/ppc/pmac.c
  ide: ST320413A has the same problem as ST340823A

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Fix timekeeping on PowerPC 601
  [POWERPC] Don't expose clock vDSO functions when CPU has no timebase
  [POWERPC] spusched: Fix null pointer dereference in find_victim

Randy Dunlap noticed an interesting "crashme" behaviour on his dual
Prescott Xeon setup, where he gets page faults with the error code
having a zero "user" bit, but the register state points back to user
mode.

This may be a CPU microcode buglet triggered by some strange instruction
pattern that crashme generates, and loading a microcode update seems to
possibly have fixed it.

Regardless, we really should trust the register state more than the
error code, since it's really the register state that determines whether
we can actually send a signal, or whether we're in kernel mode and need
to oops/kill the process in the case of a page fault.

Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix the definition of the ioasic_ssr_lock spinlock to include a proper 
initialisation.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Nested class devices used to have 'device' symlink point to a real
(physical) device instead of a parent class device.  When converting
subsystems to struct device we need to keep doing what class devices did if
CONFIG_SYSFS_DEPRECATED is Y, otherwise parts of udev break.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: NGreg KH <greg@kroah.com>
Tested-by: NAnssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes a crash caused by an interrupt coming in when an IRQ stack
is being torn down.  When this happens, handle_signal will loop, setting up
the IRQ stack again because the tearing down had finished, and handling
whatever signals had come in.

However, to_irq_stack returns a mask of pending signals to be handled, plus
bit zero is set if the IRQ stack was already active, and thus shouldn't be
torn down.  This causes a problem because when handle_signal goes around
the loop, sig will be zero, and to_irq_stack will duly set bit zero in the
returned mask, faking handle_signal into believing that it shouldn't tear
down the IRQ stack and return thread_info pointers back to their original
values.

This will eventually cause a crash, as the IRQ stack thread_info will
continue pointing to the original task_struct and an interrupt will look
into it after it has been freed.

The fix is to stop passing a signal number into to_irq_stack.  Rather, the
pending signals mask is initialized beforehand with the bit for sig already
set.  References to sig in to_irq_stack can be replaced with references to
the mask.

[akpm@linux-foundation.org: use UL]
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch proposes fixes to the reference counting of memory policy in the
page allocation paths and in show_numa_map().  Extracted from my "Memory
Policy Cleanups and Enhancements" series as stand-alone.

Shared policy lookup [shmem] has always added a reference to the policy,
but this was never unrefed after page allocation or after formatting the
numa map data.

Default system policy should not require additional ref counting, nor
should the current task's task policy.  However, show_numa_map() calls
get_vma_policy() to examine what may be [likely is] another task's policy.
The latter case needs protection against freeing of the policy.

This patch adds a reference count to a mempolicy returned by
get_vma_policy() when the policy is a vma policy or another task's
mempolicy.  Again, shared policy is already reference counted on lookup.  A
matching "unref" [__mpol_free()] is performed in alloc_page_vma() for
shared and vma policies, and in show_numa_map() for shared and another
task's mempolicy.  We can call __mpol_free() directly, saving an admittedly
inexpensive inline NULL test, because we know we have a non-NULL policy.

Handling policy ref counts for hugepages is a bit trickier.
huge_zonelist() returns a zone list that might come from a shared or vma
'BIND policy.  In this case, we should hold the reference until after the
huge page allocation in dequeue_hugepage().  The patch modifies
huge_zonelist() to return a pointer to the mempolicy if it needs to be
unref'd after allocation.

Kernel Build [16cpu, 32GB, ia64] - average of 10 runs:

		w/o patch	w/ refcount patch
	    Avg	  Std Devn	   Avg	  Std Devn
Real:	 100.59	    0.38	 100.63	    0.43
User:	1209.60	    0.37	1209.91	    0.31
System:   81.52	    0.42	  81.64	    0.34
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: NAndi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It turned out, that the user namespace is released during the do_exit() in
exit_task_namespaces(), but the struct user_struct is released only during the
put_task_struct(), i.e.  MUCH later.

On debug kernels with poisoned slabs this will cause the oops in
uid_hash_remove() because the head of the chain, which resides inside the
struct user_namespace, will be already freed and poisoned.

Since the uid hash itself is required only when someone can search it, i.e.
when the namespace is alive, we can safely unhash all the user_struct-s from
it during the namespace exiting.  The subsequent free_uid() will complete the
user_struct destruction.

For example simple program

   #include <sched.h>

   char stack[2 * 1024 * 1024];

   int f(void *foo)
   {
   	return 0;
   }

   int main(void)
   {
   	clone(f, stack + 1 * 1024 * 1024, 0x10000000, 0);
   	return 0;
   }

run on kernel with CONFIG_USER_NS turned on will oops the
kernel immediately.

This was spotted during OpenVZ kernel testing.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@openvz.org>
Acked-by: N"Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Surprisingly, but (spotted by Alexey Dobriyan) the uid hash still uses
list_heads, thus occupying twice as much place as it could.  Convert it to
hlist_heads.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@openvz.org>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kernel/user.c: Convert list_for_each to list_for_each_entry in
uid_hash_find()
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The do_split() function for htree dir blocks is intended to split a leaf
block to make room for a new entry.  It sorts the entries in the original
block by hash value, then moves the last half of the entries to the new
block - without accounting for how much space this actually moves.  (IOW,
it moves half of the entry *count* not half of the entry *space*).  If by
chance we have both large & small entries, and we move only the smallest
entries, and we have a large new entry to insert, we may not have created
enough space for it.

The patch below stores each record size when calculating the dx_map, and
then walks the hash-sorted dx_map, calculating how many entries must be
moved to more evenly split the existing entries between the old block and
the new block, guaranteeing enough space for the new entry.

The dx_map "offs" member is reduced to u16 so that the overall map size
does not change - it is temporarily stored at the end of the new block, and
if it grows too large it may be overwritten.  By making offs and size both
u16, we won't grow the map size.

Also add a few comments to the functions involved.

This fixes the testcase reported by hooanon05@yahoo.co.jp on the
linux-ext4 list, "ext3 dir_index causes an error"

Thanks to Andreas Dilger for discussing the problem & solution with me.
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Signed-off-by: NAndreas Dilger <adilger@clusterfs.com>
Tested-by: NJunjiro Okajima <hooanon05@yahoo.co.jp>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <linux-ext4@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is still some confusion and disagreement over what this interface should
actually do.  So it is best that we disable it in 2.6.23 until we get that
fully sorted out.

(sys_timerfd() was present in 2.6.22 but it was apparently broken, so here we
assume that nobody is using it yet).

Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Davide Libenzi <davidel@xmailserver.org>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

NFS unregisters sysctls only if V4 support is compiled in.  However, sysctl
table is not V4 specific, so unregister it always.

Steps to reproduce:

	[build nfs.ko with CONFIG_NFS_V4=n]
	modrobe nfs
	rmmod nfs
	ls /proc/sys

Unable to handle kernel paging request at ffffffff880661c0 RIP:
 [<ffffffff802af8e3>] proc_sys_readdir+0xd3/0x350
PGD 203067 PUD 207063 PMD 7e216067 PTE 0
Oops: 0000 [1] SMP
CPU 1
Modules linked in: lockd nfs_acl sunrpc
Pid: 3335, comm: ls Not tainted 2.6.23-rc3-bloat #2
RIP: 0010:[<ffffffff802af8e3>]  [<ffffffff802af8e3>] proc_sys_readdir+0xd3/0x350
RSP: 0018:ffff81007fd93e78  EFLAGS: 00010286
RAX: ffffffff880661c0 RBX: ffffffff80466370 RCX: ffffffff880661c0
RDX: 00000000000014c0 RSI: ffff81007f3ad020 RDI: ffff81007efd8b40
RBP: 0000000000000018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: ffffffff802a8570 R12: ffffffff880661c0
R13: ffff81007e219640 R14: ffff81007efd8b40 R15: ffff81007ded7280
FS:  00002ba25ef03060(0000) GS:ffff81007ff81258(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffff880661c0 CR3: 000000007dfaf000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process ls (pid: 3335, threadinfo ffff81007fd92000, task ffff81007d8a0000)
Stack:  ffff81007f3ad150 ffffffff80283f30 ffff81007fd93f48 ffff81007efd8b40
 ffff81007ee00440 0000000422222222 0000000200035593 ffffffff88037e9a
 2222222222222222 ffffffff80466500 ffff81007e416400 ffff81007e219640
Call Trace:
 [<ffffffff80283f30>] filldir+0x0/0xf0
 [<ffffffff80283f30>] filldir+0x0/0xf0
 [<ffffffff802840c7>] vfs_readdir+0xa7/0xc0
 [<ffffffff80284376>] sys_getdents+0x96/0xe0
 [<ffffffff8020bb3e>] system_call+0x7e/0x83

Code: 41 8b 14 24 85 d2 74 dc 49 8b 44 24 08 48 85 c0 74 e7 49 3b
RIP  [<ffffffff802af8e3>] proc_sys_readdir+0xd3/0x350
 RSP <ffff81007fd93e78>
CR2: ffffffff880661c0
Kernel panic - not syncing: Fatal exception
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NTrond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert asserts (BUGs) in dx_probe from bad on-disk data to recoverable
errors with helpful warnings.  With help catching other asserts from Duane
Griffin <duaneg@dghda.com>
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Acked-by: NDuane Griffin <duaneg@dghda.com>
Acked-by: NTheodore Ts'o <tytso@mit.edu>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The mask on i830 should be 0x70 always, later chips 0xF0 should be okay.
Signed-off-by: NDave Airlie <airlied@linux.ie>
Acked-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Cc: Michael Haas <laga@laga.ath.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reported in Kernel Bugzilla 9006

Fix an obvious bug in DPLL disable.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Xen ignores all updates to cr4, and some versions will kill the domain if
you try to change its value.  Just ignore all changes.
Signed-off-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a couple drivers that do not correctly terminate their pci_device_id
lists.  This results in garbage being spewed into modules.pcimap when the
module happens to not have 28 NULL bytes following the table, and/or the
last PCI ID is actually truncated from the table when calculating the
modules.alias PCI aliases, cause those unfortunate device IDs to not
auto-load.
Signed-off-by: NKees Cook <kees@ubuntu.com>
Acked-by: NCorey Minyard <minyard@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The shrinking of a virtual memory area that is mmap(2)'d to a memory
special file (device drivers/char/mspec.c) can cause a panic.

If the mapped size of the vma (vm_area_struct) is very large, mspec allocates
a large vma_data structure with vmalloc(). But such a vma can be shrunk by
an munmap(2).  The current driver uses the current size of each vma to
deduce whether its vma_data structure was allocated by kmalloc() or vmalloc().
So if the vma was shrunk it appears to have been allocated by kmalloc(),
and mspec attempts to free it with kfree().  This results in a panic.

This patch avoids the panic (by preserving the type of the allocation) and
also makes mspec work correctly as the vma is split into pieces by the
munmap(2)'s.

All vma's derived from such a split vma share the same vma_data structure that
represents all the pages mapped into this set of vma's.  The mpec driver
must be made capable of using the right portion of the structure for each
member vma.  In other words, it must index into the array of page addresses
using the portion of the array that represents the current vma. This is
enabled by storing the vma group's vm_start in the vma_data structure.

The shared vma_data's are not protected by mm->mmap_sem in the fork() case
so the reference count is left as atomic_t.
Signed-off-by: NCliff Wickman <cpw@sgi.com>
Acked-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently the rtc driver, rtc-ds1552.c uses an unsigned long to store the
base mmio address of the NVRAM/RTC.  This breaks on 32-bit systems with
larger physical addresses.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently the rtc driver, rtc-ds1742.c uses an unsigned long to store the
base mmio address of the NVRAM/RTC.  This breaks on systems like PowerPC
440, which is a 32-bit core with 36-bit physical addresses: IO on the
system, including the RTC, is typically above the 4GB point, and cannot fit
into an unsigned long.

This patch fixes the problem by replacing the unsigned long with a
resource_size_t.  Tested on Ebony (PPC440) (with additional patches to
instantiate the ds1742 platform device appropriately).
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

struct utsname is copied from master one without any exclusion.

Here is sample output from one proggie doing

	sethostname("aaaaaaaaaaaaaaaaaaaaaaaaaaaaaa");
	sethostname("bbbbbbbbbbbbbbbbbbbbbbbbbbbbbb");

and another

	clone(,, CLONE_NEWUTS, ...)
	uname()

	hostname = 'aaaaaaaaaaaaaaaaaaaaaaaaabbbbb'
	hostname = 'bbbaaaaaaaaaaaaaaaaaaaaaaaaaaa'
	hostname = 'aaaaaaaabbbbbbbbbbbbbbbbbbbbbb'
	hostname = 'aaaaaaaaaaaaaaaaaaaaaaaaaabbbb'
	hostname = 'aaaaaaaaaaaaaaaaaaaaaaaaaaaabb'
	hostname = 'aaabbbbbbbbbbbbbbbbbbbbbbbbbbb'
	hostname = 'bbbbbbbbbbbbbbbbaaaaaaaaaaaaaa'

Hostname is sometimes corrupted.

Yes, even _the_ simplest namespace activity had bug in it. :-(
Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 83144186 (Freezer: make kernel
threads nonfreezable by default) breaks freezing when attempting to resume
from an initrd, because the init (which is freezeable) spins while waiting
for another thread to run /linuxrc, but doesn't check whether it has been
told to enter the refrigerator.  The original patch replaced a call to
try_to_freeze() with a call to yield().  I believe a simple reversion is
wrong because if !CONFIG_PM_SLEEP, try_to_freeze() is a noop.  It should
still yield.
Signed-off-by: NNigel Cunningham <nigel@nigel.suspend2.net>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I found a type mismatch in UML that makes host block devices unusable as ubd
devices on x86_64 and other 64 bits systems (segfault of the mm subsystem):

In block/ioctl.c, the following lines show that the BLKGETSIZE ioctl expects
a pointer to a long:

	case BLKGETSIZE:
		if ((bdev->bd_inode->i_size >> 9) > ~0UL)
			return -EFBIG;
		return put_ulong(arg, bdev->bd_inode->i_size >> 9);

In arch/um/os-Linux/file.c, os_file_size calls it with an int.

The ioctl_list man page should be fixed as well.

Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sparc32:

drivers/block/DAC960.c: In function 'DAC960_V1_EnableMemoryMailboxInterface':
drivers/block/DAC960.c:1168: error: 'DMA_32BIT_MASK' undeclared (first use in this function)
drivers/block/DAC960.c:1168: error: (Each undeclared identifier is reported only

Cc: <dac@conglom-o.org>
Cc: <stable@kernel.org>
Cc: Alessandro Polverini <alex@nibbles.it>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recent changes to the timekeeping code broke support for the PowerPC 601
processor which doesn't have the usual timebase facility but a slightly
different thing called (yuck) the RTC.

This fixes it, boot tested on an old 601 based PowerMac 7200.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We forgot to remove the clock_gettime, clock_getres and get_tbfreq vDSO
calls on CPUs that have no timebase such as 601 or 403 (old CPUs that have
different mechanisms and for which the vDSO code will not work properly).
This fixes it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

find_victim can dereference a NULL pointer when iterating over the list
of victim spus because list_mutex only guarantees spu->ct to be stable,
but of course not to be non-NULL.

Also fix find_victim to not call spu_unbind_context without list_mutex
because that violates the above guarantee.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>