Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 27 4月, 2016 2 次提交
  3. 14 4月, 2016 2 次提交
  5. 15 2月, 2016 3 次提交
  7. 04 2月, 2016 2 次提交
  9. 02 12月, 2015 2 次提交
  11. 17 10月, 2015 2 次提交
  13. 04 10月, 2015 4 次提交
  15. 09 8月, 2015 2 次提交
  17. 23 7月, 2015 1 次提交
  19. 31 5月, 2015 1 次提交
  21. 25 5月, 2015 1 次提交
    • C
      usb: host: xhci: add mutex for non-thread-safe data · a00918d0
      由 Chris Bainbridge 提交于 
      Regression in commit 638139eb ("usb: hub: allow to process more usb
hub events in parallel")

The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.

This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to

commit 6fecd4f2 ("USB: separate usb_address0 mutexes for each bus")

With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.

Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.

Fixes multiple boot errors:

[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device

And:

[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device

And:

[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device

And:

[ 11.018386] usb 1-3: device descriptor read/all, error -110

And:

[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command

Tested with 200 reboots, resulting in no USB hub init related errors.

Fixes: 638139eb ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.comSigned-off-by: NChris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      a00918d0
  23. 10 5月, 2015 1 次提交
    • M
      xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256 · 18cc2f4c
      由 Mathias Nyman 提交于 
      Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)

With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.

A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and  and Split transaction errors for LS/FS
interrupt devices.

Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.

The default size used to be 64 TRBs per segment

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      18cc2f4c
  25. 11 3月, 2015 1 次提交
  27. 07 3月, 2015 2 次提交
    • M
      xhci: Workaround for PME stuck issues in Intel xhci · b8cb91e0
      由 Mathias Nyman 提交于 
      The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.

Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks

Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      b8cb91e0
    • A
      xhci: fix reporting of 0-sized URBs in control endpoint · 45ba2154
      由 Aleksander Morgado 提交于 
      When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.

The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.

This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.

This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.

Cc: <stable@vger.kernel.org>
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      45ba2154
  29. 25 2月, 2015 2 次提交
  31. 25 1月, 2015 1 次提交
  33. 10 1月, 2015 2 次提交
  35. 03 12月, 2014 2 次提交
  37. 22 11月, 2014 1 次提交
  39. 04 10月, 2014 3 次提交
  41. 24 9月, 2014 2 次提交
  43. 02 8月, 2014 1 次提交
    • H
      xhci: Blacklist using streams on the Etron EJ168 controller · 8f873c1f
      由 Hans de Goede 提交于 
      Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.

The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.

This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.

But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.

The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.

Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.

https://bugzilla.redhat.com/show_bug.cgi?id=1121288
https://bugzilla.kernel.org/show_bug.cgi?id=80101

Cc: stable@vger.kernel.org # 3.15
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      8f873c1f