In case a subtree did not match we currently stop backtracking and return
NULL (root table from fib_lookup). This could yield in invalid routing
table lookups when using subtrees.

Instead continue to backtrack until a valid subtree or node is found
and return this match.

Also remove unneeded NULL check.
Reported-by: NTeco Boot <teco@inf-net.nl>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David Lamparter <equinox@diac24.net>
Cc: <boutier@pps.univ-paris-diderot.fr>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While investigating about strange increase of retransmit rates
on hosts ~24 days after boot, Van found hystart was disabled
if ca->epoch_start was 0, as following condition is true
when tcp_time_stamp high order bit is set.

(s32)(tcp_time_stamp - ca->epoch_start) < HZ

Quoting Van :

 At initialization & after every loss ca->epoch_start is set to zero so
 I believe that the above line will turn off hystart as soon as the 2^31
 bit is set in tcp_time_stamp & hystart will stay off for 24 days.
 I think we've observed that cubic's restart is too aggressive without
 hystart so this might account for the higher drop rate we observe.
Diagnosed-by: NVan Jacobson <vanj@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

br_sysfs_if.c is for sysfs attributes of bridge ports, while br_sysfs_br.c
is for sysfs attributes of bridge itself. Correct the comment here.
Signed-off-by: NWang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 17a6e9f1 ("tcp_cubic: fix clock dependency") added an
overflow error in bictcp_update() in following code :

/* change the unit from HZ to bictcp_HZ */
t = ((tcp_time_stamp + msecs_to_jiffies(ca->delay_min>>3) -
      ca->epoch_start) << BICTCP_HZ) / HZ;

Because msecs_to_jiffies() being unsigned long, compiler does
implicit type promotion.

We really want to constrain (tcp_time_stamp - ca->epoch_start)
to a signed 32bit value, or else 't' has unexpected high values.

This bugs triggers an increase of retransmit rates ~24 days after
boot [1], as the high order bit of tcp_time_stamp flips.

[1] for hosts with HZ=1000

Big thanks to Van Jacobson for spotting this problem.
Diagnosed-by: NVan Jacobson <vanj@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we are reading an uninitialized value for the max_delay
variable when snooping an MLD query message of invalid length and would
update our timers with that.

Fixing this by simply ignoring such broken MLD queries (just like we do
for IGMP already).

This is a regression introduced by:
"bridge: disable snooping if there is no querier" (b00589af)
Reported-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AddressSanitizer [1] dynamic checker pointed a potential
out of bound access in leaf_walk_rcu()

We could allocate one more slot in tnode_new() to leave the prefetch()
in-place but it looks not worth the pain.

Bug added in commit 82cfbb00 ("[IPV4] fib_trie: iterator recode")

[1] :
https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernelReported-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev->ndo_neigh_setup() might need some of the values of neigh_parms, so
populate them before calling it.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 91657eaf ("xfrm: take net hdr len into account for esp payload
size calculation") introduced a possible interger overflow in
esp{4,6}_get_mtu() handlers in case of x->props.mode equals
XFRM_MODE_TUNNEL. Thus, the following expression will overflow

  unsigned int net_adj;
  ...
  <case ipv{4,6} XFRM_MODE_TUNNEL>
         net_adj = 0;
  ...
  return ((mtu - x->props.header_len - crypto_aead_authsize(esp->aead) -
           net_adj) & ~(align - 1)) + (net_adj - 2);

where (net_adj - 2) would be evaluated as <foo> + (0 - 2) in an unsigned
context. Fix it by simply removing brackets as those operations here
do not need to have special precedence.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Benjamin Poirier <bpoirier@suse.de>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: NBenjamin Poirier <bpoirier@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vlan devices are LLTX and don't update their own trans_start, so if
dev_trans_start has to be called with a vlan device then 0 or a stale
value will be returned. Currently the bonding is the only such user, and
it's needed for proper arp monitoring when the slaves are vlans.
Fix this by extracting the vlan's real device trans_start.
Suggested-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes we might have stacked vlans on top of each other, and we're
interested in the first non-vlan real device on the path, so transform
vlan_dev_real_dev to go over the stacked vlans and extract the first
non-vlan device.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop the semicolon at the end of the list_for_each_entry loop header.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NetLabel has the ability to selectively assign network security labels
to outbound traffic based on either the LSM's "domain" (different for
each LSM), the network destination, or a combination of both.  Depending
on the type of traffic, local or forwarded, and the type of traffic
selector, domain or address based, different hooks are used to label the
traffic; the goal being minimal overhead.

Unfortunately, there is a bug such that a system using NetLabel domain
based traffic selectors does not correctly label outbound local traffic
that is not assigned to a socket.  The issue is that in these cases
the associated NetLabel hook only looks at the address based selectors
and not the domain based selectors.  This patch corrects this by
checking both the domain and address based selectors so that the correct
labeling is applied, regardless of the configuration type.

In order to acomplish this fix, this patch also simplifies some of the
NetLabel domainhash structures to use a more common outbound traffic
mapping type: struct netlbl_dommap_def.  This simplifies some of the code
in this patch and paves the way for further simplifications in the
future.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's possible to assign an invalid value to the net.core.somaxconn
sysctl variable, because there is no checks at all.

The sk_max_ack_backlog field of the sock structure is defined as
unsigned short. Therefore, the backlog argument in inet_listen()
shouldn't exceed USHRT_MAX. The backlog argument in the listen() syscall
is truncated to the somaxconn value. So, the somaxconn value shouldn't
exceed 65535 (USHRT_MAX).
Also, negative values of somaxconn are meaningless.

before:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
net.core.somaxconn = 65536
$ sysctl -w net.core.somaxconn=-100
net.core.somaxconn = -100

after:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
error: "Invalid argument" setting key "net.core.somaxconn"
$ sysctl -w net.core.somaxconn=-100
error: "Invalid argument" setting key "net.core.somaxconn"

Based on a prior patch from Changli Gao.
Signed-off-by: NRoman Gushchin <klamm@yandex-team.ru>
Reported-by: NChangli Gao <xiaosuo@gmail.com>
Suggested-by: NEric Dumazet <edumazet@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5c766d64 ("ipv4: introduce address lifetime") leaves the ifa
resource that was allocated via inet_alloc_ifa() unfreed when returning
the function with -EINVAL. Thus, free it first via inet_free_ifa().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When userspace passes a large priority value
the assignment of the unsigned value hopt->prio
to  signed int cl->prio causes cl->prio to become negative and the
comparison is with TC_HTB_NUMPRIO is always false.

The result is that HTB crashes by referencing outside
the array when processing packets. With this patch the large value
wraps around like other values outside the normal range.

See: https://bugzilla.kernel.org/show_bug.cgi?id=60669Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creation of TIPC internal server socket fails,
we get an oops with the following dump:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffffa0011f49>] tipc_close_conn+0x59/0xb0 [tipc]
PGD 13719067 PUD 12008067 PMD 0
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: tipc(+)
CPU: 4 PID: 4340 Comm: insmod Not tainted 3.10.0+ #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
task: ffff880014360000 ti: ffff88001374c000 task.ti: ffff88001374c000
RIP: 0010:[<ffffffffa0011f49>]  [<ffffffffa0011f49>] tipc_close_conn+0x59/0xb0 [tipc]
RSP: 0018:ffff88001374dc98  EFLAGS: 00010292
RAX: 0000000000000000 RBX: ffff880012ac09d8 RCX: 0000000000000000
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffff880014360000
RBP: ffff88001374dcb8 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa0016fa0
R13: ffffffffa0017010 R14: ffffffffa0017010 R15: ffff880012ac09d8
FS:  0000000000000000(0000) GS:ffff880016600000(0063) knlGS:00000000f76668d0
CS:  0010 DS: 002b ES: 002b CR0: 000000008005003b
CR2: 0000000000000020 CR3: 0000000012227000 CR4: 00000000000006e0
Stack:
ffff88001374dcb8 ffffffffa0016fa0 0000000000000000 0000000000000001
ffff88001374dcf8 ffffffffa0012922 ffff88001374dce8 00000000ffffffea
ffffffffa0017100 0000000000000000 ffff8800134241a8 ffffffffa0017150
Call Trace:
[<ffffffffa0012922>] tipc_server_stop+0xa2/0x1b0 [tipc]
[<ffffffffa0009995>] tipc_subscr_stop+0x15/0x20 [tipc]
[<ffffffffa00130f5>] tipc_core_stop+0x1d/0x33 [tipc]
[<ffffffffa001f0d4>] tipc_init+0xd4/0xf8 [tipc]
[<ffffffffa001f000>] ? 0xffffffffa001efff
[<ffffffff8100023f>] do_one_initcall+0x3f/0x150
[<ffffffff81082f4d>] ? __blocking_notifier_call_chain+0x7d/0xd0
[<ffffffff810cc58a>] load_module+0x11aa/0x19c0
[<ffffffff810c8d60>] ? show_initstate+0x50/0x50
[<ffffffff8190311c>] ? retint_restore_args+0xe/0xe
[<ffffffff810cce79>] SyS_init_module+0xd9/0x110
[<ffffffff8190dc65>] sysenter_dispatch+0x7/0x1f
Code: 6c 24 70 4c 89 ef e8 b7 04 8f e1 8b 73 04 4c 89 e7 e8 7c 9e 32 e1 41 83 ac 24
b8 00 00 00 01 4c 89 ef e8 eb 0a 8f e1 48 8b 43 08 <4c> 8b 68 20 4d 8d a5 48 03 00
00 4c 89 e7 e8 04 05 8f e1 4c 89
RIP  [<ffffffffa0011f49>] tipc_close_conn+0x59/0xb0 [tipc]
RSP <ffff88001374dc98>
CR2: 0000000000000020
---[ end trace b02321f40e4269a3 ]---

We have the following call chain:

tipc_core_start()
    ret = tipc_subscr_start()
        ret = tipc_server_start(){
                  server->enabled = 1;
                  ret = tipc_open_listening_sock()
              }

I.e., the server->enabled flag is unconditionally set to 1, whatever
the return value of tipc_open_listening_sock().

This causes a crash when tipc_core_start() tries to clean up
resources after a failed initialization:

    if (ret == failed)
        tipc_subscr_stop()
            tipc_server_stop(){
                if (server->enabled)
                    tipc_close_conn(){
                        NULL reference of con->sock-sk
                        OOPS!
                }
            }

To avoid this, tipc_server_start() should only set server->enabled
to 1 in case of a succesful socket creation. In case of failure, it
should release all allocated resources before returning.

Problem introduced in commit c5fa7b3c
("tipc: introduce new TIPC server infrastructure") in v3.11-rc1.
Note that it won't be seen often; it takes a module load under memory
constrained conditions in order to trigger the failure condition.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.

Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a race in IPv6 automatic addess assignment. The address is created
with zero lifetime when it's added to various address lists. Before it gets
assigned the correct lifetime, there's a window where a new address may be
configured. This causes the semi-initiated address to be deleted in
addrconf_verify.

This was discovered as a reference leak caused by concurrent run of
__ipv6_ifa_notify for both RTM_NEWADDR and RTM_DELADDR with the same
address.

Fix this by setting the lifetime before the address is added to
inet6_addr_lst.

A few notes:

1. In addrconf_prefix_rcv, by setting update_lft to zero, the
   if (update_lft) { ... } condition is no longer executed for newly
   created addresses. This is okay, as the ifp fields are set in
   ipv6_add_addr now and ipv6_ifa_notify is called (and has been called)
   through addrconf_dad_start.

2. The removal of the whole block under ifp->lock in inet6_addr_add is okay,
   too, as tstamp is initialized to jiffies in ipv6_add_addr.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should
hold the last time garbage collector was run so that we should
update it whenever fib6_run_gc() calls fib6_clean_all(), not only
if we got there from ip6_dst_gc().
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.

This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.

Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The change made to rsc_parse() in
0dc1531a "svcrpc: store gss mech in
svc_cred" should also have been propagated to the gss-proxy codepath.
This fixes a crash in the gss-proxy case.
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

mech_oid.data is an array, not kmalloc()'d memory.

Cc: stable@vger.kernel.org
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

Uninitialized stack data was being used as the destination for memcpy's.

Longer term we'll just delete some of this code; all we're doing is
skipping over xdr that we don't care about.

Cc: stable@vger.kernel.org
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

Cc: stable@vger.kernel.org
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

Since we enabled auto-tuning for sunrpc TCP connections we do not
guarantee that there is enough write-space on each connection to
queue a reply.

If memory pressure causes the window to shrink too small, the request
throttling in sunrpc/svc will not accept any requests so no more requests
will be handled.  Even when pressure decreases the window will not
grow again until data is sent on the connection.
This means we get a deadlock:  no requests will be handled until there
is more space, and no space will be allocated until a request is
handled.

This can be simulated by modifying svc_tcp_has_wspace to inflate the
number of byte required and removing the 'svc_sock_setbufsize' calls
in svc_setup_socket.

I found that multiplying by 16 was enough to make the requirement
exceed the default allocation.  With this modification in place:
   mount -o vers=3,proto=tcp 127.0.0.1:/home /mnt
would block and eventually time out because the nfs server could not
accept any requests.

This patch relaxes the request throttling to always allow at least one
request through per connection.  It does this by checking both
  sk_stream_min_wspace() and xprt->xpt_reserved
are zero.
The first is zero when the TCP transmit queue is empty.
The second is zero when there are no RPC requests being processed.
When both of these are zero the socket is idle and so one more
request can safely be allowed through.

Applying this patch allows the above mount command to succeed cleanly.
Tracing shows that the allocated write buffer space quickly grows and
after a few requests are handled, the extra tests are no longer needed
to permit further requests to be processed.

The main purpose of request throttling is to handle the case when one
client is slow at collecting replies and the send queue gets full of
replies that the client hasn't acknowledged (at the TCP level) yet.
As we only change behaviour when the send queue is empty this main
purpose is still preserved.
Reported-by: NBen Myers <bpm@sgi.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

If there is no querier on a link then we won't get periodic reports and
therefore won't be able to learn about multicast listeners behind ports,
potentially leading to lost multicast packets, especially for multicast
listeners that joined before the creation of the bridge.

These lost multicast packets can appear since c5c23260
("bridge: Add multicast_querier toggle and disable queries by default")
in particular.

With this patch we are flooding multicast packets if our querier is
disabled and if we didn't detect any other querier.

A grace period of the Maximum Response Delay of the querier is added to
give multicast responses enough time to arrive and to be learned from
before disabling the flooding behaviour again.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "pvc" struct has a hole after pvc.sap_family which is not cleared.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.

Cc: stable@vger.kernel.org
Reported-by: NChris Wright <chrisw@sous-sol.org>
Tested-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a P2P GO interface goes down, cfg80211 doesn't properly
tear it down, leading to warnings later. Add the GO interface
type to the enumeration to tear it down like AP interfaces.
Otherwise, we leave it pending and mac80211's state can get
very confused, leading to warnings later.

Cc: stable@vger.kernel.org
Reported-by: NIlan Peer <ilan.peer@intel.com>
Tested-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.

Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.

Work around this by ignoring the HT primary channel information in
beacons if we're already connected.

Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.

Cc: stable@vger.kernel.org [3.10]
Acked-by: NAndy Isaacson <adi@hexapodia.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

TX status notification can get lost, or the frames could
get stuck on the queue, so don't wait for the callback
from the driver forever and instead time out after half
a second.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit "3d9646d0 mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop.  When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely.  Replace goto with
break and carry on.  This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking.  Thanks to Derek Atkins
as an extra pair of debugging eyes.

Cc: stable@kernel.org
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, it is not possible to use neither NLM_F_EXCL nor
NLM_F_REPLACE from genetlink. This is due to this checking in
genl_family_rcv_msg:

	if (nlh->nlmsg_flags & NLM_F_DUMP)

NLM_F_DUMP is NLM_F_MATCH|NLM_F_ROOT. Thus, if NLM_F_EXCL or
NLM_F_REPLACE flag is set, genetlink believes that you're
requesting a dump and it calls the .dumpit callback.

The solution that I propose is to refine this checking to
make it stricter:

	if ((nlh->nlmsg_flags & NLM_F_DUMP) == NLM_F_DUMP)

And given the combination NLM_F_REPLACE and NLM_F_EXCL does
not make sense to me, it removes the ambiguity.

There was a patch that tried to fix this some time ago (0ab03c2b
netlink: test for all flags of the NLM_F_DUMP composite) but it
tried to resolve this ambiguity in *all* existing netlink subsystems,
not only genetlink. That patch was reverted since it broke iproute2,
which is using NLM_F_ROOT to request the dump of the routing cache.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is inspired by a5cc68f3 "af_key: fix info leaks in notify
messages".  There are some struct members which don't get initialized
and could disclose small amounts of private information.
Acked-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Loading a firmware into a target is typically called firmware
download, not firmware upload. So we rename the netlink API to
NFC_CMD_FW_DOWNLOAD in order to avoid any terminology confusion from
userspace.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is similar to the race Linus had reported, but in this case
it's an older bug: nl80211_prepare_wdev_dump() uses the wiphy
index in cb->args[0] as it is and thus parses the message over
and over again instead of just once because 0 is the first valid
wiphy index. Similar code in nl80211_testmode_dump() correctly
offsets the wiphy_index by 1, do that here as well.

Cc: stable@vger.kernel.org
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make sure the reserved fields, and padding (if any), are
fully initialized.

Based upon a patch by Dan Carpenter and feedback from
Joe Perches.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain circumstances, such as an HCI driver using __hci_cmd_sync_ev
with HCI_EV_CMD_COMPLETE as the expected completion event there is the
chance that hci_event_packet will call hci_req_cmd_complete twice (once
for the explicitly looked after event and another time in the actual
handler of cmd_complete).

In the case of __hci_cmd_sync_ev this introduces a race where the first
call wakes up the blocking __hci_cmd_sync_ev and lets it complete.
However, by the time that a second __hci_cmd_sync_ev call is already in
progress the second hci_req_cmd_complete call (from the previous
operation) will wake up the blocking function prematurely and cause it
to fail, as witnessed by the following log:

[  639.232195] hci_rx_work: hci0 Event packet
[  639.232201] hci_req_cmd_complete: opcode 0xfc8e status 0x00
[  639.232205] hci_sent_cmd_data: hci0 opcode 0xfc8e
[  639.232210] hci_req_sync_complete: hci0 result 0x00
[  639.232220] hci_cmd_complete_evt: hci0 opcode 0xfc8e
[  639.232225] hci_req_cmd_complete: opcode 0xfc8e status 0x00
[  639.232228] __hci_cmd_sync_ev: hci0 end: err 0
[  639.232234] __hci_cmd_sync_ev: hci0
[  639.232238] hci_req_add_ev: hci0 opcode 0xfc8e plen 250
[  639.232242] hci_prepare_cmd: skb len 253
[  639.232246] hci_req_run: length 1
[  639.232250] hci_sent_cmd_data: hci0 opcode 0xfc8e
[  639.232255] hci_req_sync_complete: hci0 result 0x00
[  639.232266] hci_cmd_work: hci0 cmd_cnt 1 cmd queued 1
[  639.232271] __hci_cmd_sync_ev: hci0 end: err 0
[  639.232276] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-61)
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

None of the BlueFRITZ! devices with manufacurer ID 31 (AVM Berlin)
support HCI_Read_Local_Supported_Commands. It is safe to use the
manufacturer ID (instead of e.g. a USB ID specific quirk) because the
company never created any newer controllers.

< HCI Command: Read Local Supported Comm.. (0x04|0x0002) plen 0 [hci0] 0.210014
> HCI Event: Command Status (0x0f) plen 4 [hci0] 0.217361
      Read Local Supported Commands (0x04|0x0002) ncmd 1
        Status: Unknown HCI Command (0x01)
Reported-by: NJörg Esser <jackfritt@boh.de>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Tested-by: NJörg Esser <jackfritt@boh.de>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>