We already assume that key is not NULL and dereference it in a few
other places before we check whether it is NULL, so the check is
unnecessary.  Remove it.

Fixes: 96fc6efb ("mac80211: IEEE 802.11 Extended Key ID support")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-8-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In case we got a fw restart while roaming from encrypted AP to
non-encrypted one, we might end up with hitting a warning on the pending
counter crypto_tx_tailroom_pending_dec having a non-zero value.

The following comment taken from net/mac80211/key.c explains the rational
for the delayed tailroom needed:

	/*
	* The reason for the delayed tailroom needed decrementing is to
	* make roaming faster: during roaming, all keys are first deleted
	* and then new keys are installed. The first new key causes the
	* crypto_tx_tailroom_needed_cnt to go from 0 to 1, which invokes
	* the cost of synchronize_net() (which can be slow). Avoid this
	* by deferring the crypto_tx_tailroom_needed_cnt decrementing on
	* key removal for a while, so if we roam the value is larger than
	* zero and no 0->1 transition happens.
	*
	* The cost is that if the AP switching was from an AP with keys
	* to one without, we still allocate tailroom while it would no
	* longer be needed. However, in the typical (fast) roaming case
	* within an ESS this usually won't happen.
	*/

The next flow lead to the warning eventually reported as a bug:
1. Disconnect from encrypted AP
2. Set crypto_tx_tailroom_pending_dec = 1 for the key
3. Schedule work
4. Reconnect to non-encrypted AP
5. Add a new key, setting the tailroom counter = 1
6. Got FW restart while pending counter is set ---> hit the warning

While on it, the ieee80211_reset_crypto_tx_tailroom() func was merged into
its single caller ieee80211_reenable_keys (previously called
ieee80211_enable_keys). Also, we reset the crypto_tx_tailroom_pending_dec
and remove the counters warning as we just reset both.
Signed-off-by: NLior Cohen <lior2.cohen@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-7-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

When we reach this point, the key cannot be NULL. Remove the condition
that suggests otherwise.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-6-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

"HE/HT/VHT" is a bit confusing since really the order of
development (and possible support) is different - change
this to "HT/VHT/HE".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-4-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

When the RFKILL subsystem isn't available, then rfkill_blocked()
always returns false. In the case of hardware rfkill this will
be wrong though, as if the hardware reported being killed then
it cannot operate any longer.

Since we only ever call the rfkill_sync work in this case, just
rename it to rfkill_block and always pass "true" for the blocked
parameter, rather than passing rfkill_blocked().

We rely on the underlying driver to still reject any new attempt
to bring up the device by itself.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-2-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This fixes was missed in parsing the vht capabilities max bw
support.
Signed-off-by: NMordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: e80d6425 ("mac80211: copy VHT EXT NSS BW Support/Capable data to station")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830114057.22197-1-luca@coelho.fiSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The boundary value used for the 6G band was incorrect as it would
result in invalid 6G channel number for certain frequencies.
Reported-by: NAmar Singhal <asinghal@codeaurora.org>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1567510772-24263-1-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This is useful for checking how much airtime is being used up by other
transmissions on the channel, e.g. by calculating (time_rx - time_bss_rx)
or (time_busy - time_bss_rx - time_tx)
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190828102042.58016-1-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Add NL80211_CMD_UPDATE_FT_IES to supported commands. In mac80211 drivers,
this can be implemented via existing NL80211_CMD_AUTHENTICATE and
NL80211_ATTR_IE, but non-mac80211 drivers have a separate command for
this. A driver supports FT if it either is mac80211 or supports this
command.
Signed-off-by: NMatthew Wang <matthewmwang@chromium.org>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190822174806.2954-1-matthewmwang@chromium.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently the for-loop will spin forever if variable supported is
non-zero because supported is never changed.  Fix this by adding in
the missing right shift of supported.

Addresses-Coverity: ("Infinite loop")
Fixes: 48cb3952 ("mac80211: minstrel_ht: improve rate probing for devices with static fallback")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190822122034.28664-1-colin.king@canonical.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.

Addresses-Coverity: ("Unused Value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Haiyang Zhang says:

====================
Add software backchannel and mlx5e HV VHCA stats

This patch set adds paravirtual backchannel in software in pci_hyperv,
which is required by the mlx5e driver HV VHCA stats agent.

The stats agent is responsible on running a periodic rx/tx packets/bytes
stats update.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HV VHCA stats agent is responsible on running a preiodic rx/tx
packets/bytes stats update. Currently the supported format is version
MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data
transfer from the VF to the PF.

The reporter fetch the statistics data from all opened channels, fill it
in a buffer and send it to mlx5_hv_vhca_write_agent.

As the stats layer should include some metadata per block (sequence and
offset), the HV VHCA layer shall modify the buffer before actually send it
over block 1.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Control agent is responsible over of the control block (ID 0). It should
update the PF via this block about every capability change. In addition,
upon block 0 invalidate, it should activate all other supported agents
with data requests from the PF.

Upon agent create/destroy, the invalidate callback of the control agent
is being called in order to update the PF driver about this change.

The control agent is an integral part of HV VHCA and will be created
and destroy as part of the HV VHCA init/cleanup flow.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HV VHCA is a layer which provides PF to VF communication channel based on
HyperV PCI config channel. It implements Mellanox's Inter VHCA control
communication protocol. The protocol contains control block in order to
pass messages between the PF and VF drivers, and data blocks in order to
pass actual data.

The infrastructure is agent based. Each agent will be responsible of
contiguous buffer blocks in the VHCA config space. This infrastructure will
bind agents to their blocks, and those agents can only access read/write
the buffer blocks assigned to them. Each agent will provide three
callbacks (control, invalidate, cleanup). Control will be invoked when
block-0 is invalidated with a command that concerns this agent. Invalidate
callback will be invoked if one of the blocks assigned to this agent was
invalidated. Cleanup will be invoked before the agent is being freed in
order to clean all of its open resources or deferred works.

Block-0 serves as the control block. All execution commands from the PF
will be written by the PF over this block. VF will ack on those by
writing on block-0 as well. Its format is described by struct
mlx5_hv_vhca_control_block layout.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add wrapper functions for HyperV PCIe read / write /
block_invalidate_register operations.  This will be used as an
infrastructure in the downstream patch for software communication.

This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This interface driver is a helper driver allows other drivers to
have a common interface with the Hyper-V PCI frontend driver.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Windows SR-IOV provides a backchannel mechanism in software for communication
between a VF driver and a PF driver.  These "configuration blocks" are
similar in concept to PCI configuration space, but instead of doing reads and
writes in 32-bit chunks through a very slow path, packets of up to 128 bytes
can be sent or received asynchronously.

Nearly every SR-IOV device contains just such a communications channel in
hardware, so using this one in software is usually optional.  Using the
software channel, however, allows driver implementers to leverage software
tools that fuzz the communications channel looking for vulnerabilities.

The usage model for these packets puts the responsibility for reading or
writing on the VF driver.  The VF driver sends a read or a write packet,
indicating which "block" is being referred to by number.

If the PF driver wishes to initiate communication, it can "invalidate" one or
more of the first 64 blocks.  This invalidation is delivered via a callback
supplied by the VF driver by this driver.

No protocol is implied, except that supplied by the PF and VF drivers.
Signed-off-by: NJake Oshins <jakeo@microsoft.com>
Signed-off-by: NDexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 tc flow handling for concurrent execution (Part 3)

This series includes updates to mlx5 ethernet and core driver:

Vlad submits part 3 of 3 part series to allow TC flow handling
for concurrent execution.

Vlad says:
==========

Structure mlx5e_neigh_hash_entry code that uses it are refactored in
following ways:

- Extend neigh_hash_entry with rcu and modify its users to always take
  reference to the structure when using it (neigh_hash_entry has already
  had atomic reference counter which was only used when scheduling neigh
  update on workqueue from atomic context of neigh update netevent).

- Always use mlx5e_neigh_update_table->encap_lock when modifying neigh
  update hash table and list. Originally, this lock was only used to
  synchronize with netevent handler function, which is called from bh
  context and cannot use rtnl lock for synchronization. Use rcu read lock
  instead of encap_lock to lookup nhe in atomic context of netevent even
  handler function. Convert encap_lock to mutex to allow creating new
  neigh hash entries while holding it, which is safe to do because the
  lock is no longer used in atomic context.

- Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on
  encap list to their rcu counterparts and extending encap structure
  with rcu_head to free the encap instances after rcu grace period. This
  allows fast traversal of list of encaps attached to nhe under rcu read
  lock protection.

- Take encap_table_lock when accessing encap entries in neigh update and
  neigh stats update code to protect from concurrent encap entry
  insertion or removal.

This approach leads to potential race condition when neigh update and
neigh stats update code can access encap and flow entries that are not
fully initialized or are being destroyed, or neigh can change state
without updating encaps that are created concurrently. Prevent these
issues by following changes in flow and encap initialization:

- Extend mlx5e_tc_flow with 'init_done' completion. Modify neigh update
  to wait for both encap and flow completions to prevent concurrent
  access to a structure that is being initialized by tc.

- Skip structures that failed during initialization: encaps with
  encap_id<0 and flows that don't have OFFLOADED flag set.

- To ensure that no new flows are added to encap when it is being
  accessed by neigh update or neigh stats update, take encap_table_lock
  mutex.

- To prevent concurrent deletion by tc, ensure that neigh update and
  neigh stats update hold references to encap and flow instances while
  using them.

With changes presented in this patch set it is now safe to execute tc
concurrently with neigh update and neigh stats update. However, these
two workqueue tasks modify same flow "tmp_list" field to store flows
with reference taken in temporary list to release the references after
update operation finishes and should not be executed concurrently with
each other.

Last 3 patches of this series provide 3 new mlx5 trace points to track
mlx5 tc requests and mlx5 neigh updates.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow tracing neigh state during neigh update task that is executed on
workqueue and is scheduled by neigh state change event.

Usage example:
 ># cd /sys/kernel/debug/tracing
 ># echo mlx5:mlx5e_rep_neigh_update >> set_event
 ># cat trace
    ...
    kworker/u48:7-2221  [009] ...1  1475.387435: mlx5e_rep_neigh_update:
netdev: ens1f0 MAC: 24:8a:07:9a:17:9a IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_connected=1

Added corresponding documentation in
    Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NDmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Allow tracing result of neigh used value update task that is executed
periodically on workqueue.

Usage example:
 ># cd /sys/kernel/debug/tracing
 ># echo mlx5:mlx5e_tc_update_neigh_used_value >> set_event
 ># cat trace
    ...
    kworker/u48:4-8806  [009] ...1 55117.882428: mlx5e_tc_update_neigh_used_value:
netdev: ens1f0 IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_used=1

Added corresponding documentation in
    Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NDmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Implemented following tracepoints:
1. Configure flower (mlx5e_configure_flower)
2. Delete flower (mlx5e_delete_flower)
3. Stats flower (mlx5e_stats_flower)

Usage example:
 ># cd /sys/kernel/debug/tracing
 ># echo mlx5:mlx5e_configure_flower >> set_event
 ># cat trace
    ...
    tc-6535  [019] ...1  2672.404466: mlx5e_configure_flower: cookie=0000000067874a55 actions= REDIRECT

Added corresponding documentation in
    Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: NDmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: NVlad Buslov <vladbu@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To remove dependency on rtnl lock and prevent neigh update code from
accessing uninitialized flows when executing concurrently with tc, extend
mlx5e_tc_flow with 'init_done' completion. Modify helper
mlx5e_take_all_encap_flows() to wait for flow completion after obtaining
reference to it. Modify mlx5e_tc_encap_flows_del() and
mlx5e_tc_encap_flows_add() to skip flows that don't have OFFLOADED flag
set, which can happen if concurrent flow initialization failed.

This commit finishes neigh update refactoring for concurrent execution
started in previous change in this series.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to remove dependency on rtnl lock and allow neigh update workqueue
task to execute concurrently with tc, refactor mlx5e_rep_neigh_update() for
concurrent execution:

- Lock encap table when accessing encap entry to prevent concurrent
  changes. To do this properly, the initial encap state check is moved from
  mlx5e_rep_neigh_update() into mlx5e_rep_update_flows() to be performed
  under encap_tbl_lock protection.

- Wait for encap to be fully initialized before accessing it by means of
  'res_ready' completion.

- Add mlx5e_take_all_encap_flows() helper which is used to construct a
  temporary list of flows and efi indexes that is used to access current
  encap data in flow which can be attached to multiple encaps
  simultaneously. Release the flows from temporary list after
  encap_tbl_lock critical section. This is necessary because
  mlx5e_flow_put() can't be called while holding encap_tbl_lock.

- Modify mlx5e_tc_encap_flows_add() and mlx5e_tc_encap_flows_del() to work
  with user-provided list of flows built by mlx5e_take_all_encap_flows(),
  instead of traversing encap flow list directly.

This is first step in complex neigh update refactoring, which is finished
by following commit in this series.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to remove dependency on rtnl lock and allow neigh used value
update workqueue task to execute concurrently with tc, refactor
mlx5e_tc_update_neigh_used_value() for concurrent execution:

- Lock encap table when accessing encap entry to prevent concurrent
  changes.

- Save offloaded encap flows to temporary list and release them after encap
  entry is updated. Add mlx5e_put_encap_flow_list() helper which is
  intended to be shared with neigh update code in following patch in this
  series. This is necessary because mlx5e_flow_put() can't be called while
  holding encap_tbl_lock.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on encap
list to their rcu counterparts and extending encap structure with rcu_head
to free the encap instances after rcu grace period. Use rcu read lock when
traversing encap list. Implement helper mlx5e_get_next_valid_encap()
function that is used by mlx5e_tc_update_neigh_used_value() to safely
iterate over valid entries of nhe->encap_list.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To remove dependency on rtnl lock, always take neigh update encap lock when
modifying neigh update hash table and list. Originally, this lock was only
used to synchronize with netevent handler function, which is called from bh
context and cannot use rtnl lock for synchronization. Take lock in encap
entry attach function to prevent concurrent modifications of neigh update
hash table and list.

Taking the encap lock when creating new nhe introduces a problem that we
need to allocate new entry with sleeping GFP_KERNEL flag while holding a
spinlock. However, since previous patch in this series has already
converted lookup in netevent handler function to user rcu read lock instead
of encap lock, we can safely convert the lock type to mutex.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To remove dependency on rtnl lock and to allow unlocked iteration over list
of neigh hash entries, extend nhe with rcu. Change operations on neigh list
to their rcu counterparts and free neigh hash entry with rcu timeout.

Introduce mlx5e_get_next_nhe() helper that is used to iterate over rcu
neigh list with reference to nhe taken.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Neigh entry has reference counter, however it is only used when scheduling
neigh update event. In all other cases reference to neigh entry is not
taken while working with it. Neigh code relies on synchronization provided
by rtnl lock and uses encap list size as implicit reference counter.

To remove dependency on rtnl lock, always take reference to neigh entry
while using it. Remove neigh entry from hash table and delete it only when
reference counter reaches zero. This can result spurious neigh update
events, when there is an event on entry that has zero encaps attached.
However, such events are rare and properly handled by neigh update handler.

Extend encap entry with reference to neigh hash entry in order to be able
to directly release it when encap is detached, instead of lookup nhe by key
through hash table. Extend nhe with reference to device priv structure to
guarantee correctness when nhe is used with stack devices, bond setup, in
which case it is non-trivial to determine correct device when releasing the
nhe.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

As a preparation for following refactoring that removes rtnl lock
dependency from neigh hash entry handlers, extract code that enqueues neigh
update work into standalone function. This commit doesn't change
functionality.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>