Refactor setting of VHT enabled rates in preparation of adding
some more logic there.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove the flags parameter which should be set to sync or async
according to whether this is called during sta init or not.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Info about VHT/HT rates wasn't printed properly when dumping
the rate scale table. Fix that and print more info. While at it
fix some other minor issues in the printing and prevent
overflowing the print buffer.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove code that is not needed and always allow MIMO when
in tight mode. In loose mode, we should avoid MIMO since BT
can use the other antenna to Rx while we Tx.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code limiting the AMPDU length due to BT traffic was
duplicated. Remove the redundant code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Tests have shown that we should start AMPDU even when BT
is active. So remove that constraint.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In loose BT Coex scheme, the aggregation size doesn't need to
be limited.

To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mvm doesn't support HT GF so drop all relevant code in rs.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The data in MailBox comes direclty from the BT core.
We should use the data processed by the WiFi fw that is
appended to the MailBox in the BT Coex notification.
Also decide on whether the Coex type based on the input
from the the firmware and not hard coded.

Also fix the SMPS SISO threshold to 2 (it was 3).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

VHT introduces MCS8 and MCS9. Update the expected tpt tables
to include these. Previous expected values for 20/40 MHz
are incorrect in certain cases so fix these as well.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Tested-by: NEfi Tubul <efi.tubul@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current code didn't handle well the case where we're in SISO using
ANT B and there's a BT load. Switch to ANT A in this case.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The XXX_SWITCH_ANTENNA1/2 actions keep track of switching between
3 single antennas or between 3 pairs in case of MIMO2 on a MIMO3 device.
As current and future chips will have at most 2 antennas drop these.
While at it also convert the actions into enums and cleanup
the code a bit.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

clean it up
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current and future chips supported by mvm will only have a maximum
of 2 antennas so all the MIMO3 related code and states can be dropped.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

rs_get_tbl_info_from_mcs() mistakenly clears
the rate histories window, overriding its initialization
values (i.e. filling it with 0, instead of -1).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some more cleanups of unused fields and their initializations.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This isn't very informative and can be deduced from rate_scale_table.
Remove as a preparation for dropping iwl_rs_rate_info.ieee.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

rs_ht_to_legacy and ant_toggle_lookup are arrays that
represent some state-machine. initialize them explicitly
with designated initialization to make them more clear
and avoid errors.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The traffic load monitoring isn't used anymore to decide whether
a Tx aggregation on a specific TID should be started.
No point in collecting these statistics. Remove the relevant code.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The rate scale windows are cleared twice as part of the init.
Cleanup this duplication in both mvm and dvm.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The LQ command argument isn't needed, it's always taken from the
station struct that's already passed, remove the argument.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

If someone wants to disable AMPDU, there is the 11n_disable
module parameter.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.

[same fix as for iwlegacy, thanks Stanislaw!]
Signed-off-by: NMoshe Benji <Moshe.Benji@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Another step in the rate control / BT Coex integration
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Otherwise WiFi would kill BT.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This holds for existing BA agreements.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to avoid NIC destruction due to high temperature,
CT kill will power down the NIC.

To avoid this, thermal throttling will decrease throughput
to prevent the NIC from reaching the temperature at which
CT kill is performed.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In commit 33223542
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"

I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.

Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a bug that causes the rate scaling to get stuck
when it has to use single-stream rates with a peer that
can do GF and SGI; the two are incompatible so we can't
use them together, but that causes the algorithm to not
work at all, it always rejects updates.

Disable greenfield for now to prevent that problem. The
MVM driver currently only works on devices that don't
support greenfield anyway, but better be safe and not
allow us to forget about this.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.

To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.

If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.

Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.

While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Newer firmware revisions have a completely new
firmware API. This is the new driver for this
new API.

I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.

Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Amit Beka <amit.beka@intel.com>
Cc: Amnon Paz <amnonx.paz@intel.com>
Cc: Assaf Krauss <assaf.krauss@intel.com>
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Dor Shaish <dor.shaish@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Eytan Lifshitz <eytan.lifshitz@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Update Copyright notices to 2013.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since we will have several forms of NVM (EEPROM, OTP, etc.)
and they will have different layouts, make the parsed data
more generic. This allows functional code to be independent
of a specific layout.

Also change some variables and function names from having
"eeprom" to "nvm" in their name.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a bug that causes the rate scaling to get stuck
when it has to use single-stream rates with a peer that
can do GF and SGI; the two are incompatible so we can't
use them together, but that causes the algorithm to not
work at all, it always rejects updates.

Disable greenfield for now to prevent that problem.

Cc: stable@vger.kernel.org
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EEPROM reading/parsing code is all mixed in
the driver today, and the EEPROM is parsed only
when we access data from it. This is problematic
because the NVM needs to be parsed and that is
independent of reading it. Also, the NVM format
for new devices will be different and probably
require a new parser.

Therefore refactor the reading and parsing and
create two independent components. Reading the
EEPROM requires direct hardware accesses and
therefore access to the transport, but parsing
is independent and can be done on an NVM blob.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since we're working on another mode/driver
inside iwlwifi, move the current one into a
subdirectory to more cleanly separate the
code. While at it, rename all the files.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.

Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>