Remove redundant checks and use iwl_is_ready_rf().
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is needed to avoid warning in ieee80211_restart_hw about hardware
scan in progress.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently we force scan complete at the end of iwl_scan_cancel_timeout
function. This cause race condition when we can get a new scan request
from mac80211 and complete it by iwl_bg_complete from older scan. Change
code to force scan complete only when really needed: device goes down,
interface is removed or scan timeout occurs.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assure we complete scan in mac80211 when we abort scanning (scan_abort
work) or scan timeout occurs (scan_check work). Currently
iwl_scan_cancel_timeout() procedure force scan finish in mac80211
at the end of timeout loop, so we can use it in proper work functions.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we do not get notification from hardware about scan complete, after
timeout do mac80211 scan completion anyway. This assure we end scan
in case of firmware hung.

Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assure (partially) we call ieee80211_scan_completed() only once when
scan was requested from mac80211.

Code path that first clear STATUS_SCANNING bit is responsible to call
ieee80211_scan_completed(). Before the call, we check if mac80211
really request the scan.

Still persist some cases when we behave wrong, that will be addressed
in the next patches.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since on timeout version of iwl_scan_cancel procedure we can sleep,
do not have to schedule abort_scan work to begin and perform scanning,
can do this directly. Also now, as we do not queue abort_scan from
restart work anymore, we can queue abort_scan to priv->workqueue.

Don't drop mutex when waiting for scan complete. Use STATUS_HW_SCAN bit
to check if scanning is currently pending, because STATUS_SCANNING will
be cleared only with priv->mutex taken.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we are not able to send abort command to firmware, notify mac80211
that we complete scan, as we will newer do it lately. Check for all
possible errors that low level sending command procedure does not check,
to assure we catch all failures cases.

Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Always cancel scan when stooping device and scan is currently pending,
we should newer have scan running after down device.

To assure we start scan cancel from restart work we have to schedule
abort_scan to different workqueue than priv->workqueue.

Patch fix not cancel scanning when restarting firmware, what is
one of the causes of wdev_cleanup_work warning (together with permanent
network connection lost) reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the scan completed flags handling so that we
can notify mac80211 about aborted scans with the
correct status. Also queue the scan_completed work
before the BT status update so that it won't see
the bits still set (unless a new scan was started
in which case that's fine.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rather than duplicating all the checks and even
in case of errors accepting the scan request
from mac80211, we can push the checks to the
caller and in all error cases reject the scan
request right away (rather than accepting and
then saying it was aborted).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a number of conf variables that are
unused, remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hdr pointer is left dangling after call to ieee80211_skb_resize. This
can cause guards around mesh path selection to fail.
Signed-off-by: NSteve deRosier <steve@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a path in nl80211_set_wiphy where result is tested but
uninitialized.

I am hitting this path when I attempt:

sh# iw dev wlan0 set channel 10
command failed: Unknown error 1069727332 (-1069727332)
Signed-off-by: NWilliam Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace sizeof(rtap_namespace_sizes) / sizeof(rtap_namespace_sizes[0])
with ARRAY_SIZE(rtap_namespace_sizes) in net/wireless/radiotap.c
Signed-off-by: NNikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with
ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/
sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in
drivers/net/wireless/ath/ath9k/ani.c
Signed-off-by: NNikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't generate calibration errors messages when not needed.
Signed-off-by: NFabio Rossi <rossi.f@inwind.it>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a typo introduced in "rt2x00: Add helper function for reporting tx
status" that results in an oops in rt2x00lib_txdone.
Reported-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We're handling both, the CSR_BEACON_DONE and the CSR_TWAKEUP interrupts
in rt61pci. However, these interrupts are masked out by default. Fix
this.

Found via pure code inspection.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't use all available interrupts in rt2800pci. Mask out all unused
interrupts to avoid waking up without having anything to do.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.

This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we're not using the AMPDU_BA_WINSIZE register to force the BlockAck
window size (we specify it in every TXWI) we should initialize it to 0.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The test if antenna diversity is at all enabled uses a local variable
'flags' to prepare the test condition, but uses 'ant->flags' when the test
is evaluated. The effect is that the diversity evaluation will never start.
I can see two solutions, use the 'flag' in the test condition or revert the
local flag change. My attached patch took alternative two.

Then the evaluation start but it will still not switch antenna. The problem
is a code section in rt2x00lib_config_antenna (). The effect of that code
section is that any change the diversity function perform will be
effectively shorten and no antenna selection command issued. The attached
patch will filter out any ANTENNA_SW_DIVERSITY setting but forward all
other
Signed-off-by: NLars Ericsson <lars_ericsson@telia.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To reduce scan time, enable fastcc for AR7010

(fastcc == fast channel change -- JWL)
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not maintain a persistent sdio_claim_host state. Instead,
claim host before doing IO and release host soon after.

This fixes several mmc deadlock scenarios, e.g. during
suspend/resume.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the duplicated code into single static function.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Clear the "start calib" flag only for new association,
The flag will be set in post_associate function to trigger
the runtime calibration. Set this flag to "0" will stop the
runtime sensitivity calibration
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_adjust_beacon_interval function is a bit
of black magic, so add comments to it describing
what it does. Also, in the case when there's no
beacon interval set, program the default into
the device (instead of adjusting, which results
in the max) since using the max in that case
interacts badly with dual-mode/PAN parameters.

Also update the PAN parameters accordingly and
use the same constant as here.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

In dual-mode, a number of scenarios need to be
considered, and the firmware can be very picky
about them. Adjust the timing (most importantly
the beacon interval) according to the different
modes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When the PAN context is unused, there's no
need to continually update it in the device.
So track which contexts are active (with the
special case that the WLAN context is always
active ...) and only send their commands to
the device when needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Even driver use rts/cts protection mode for aggregation packets by default.
Allow the protection mode to be configure through debugfs
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When the beacon interval needs to be changed,
all we need to do is send updated timing to
the device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When only the PAN side was active, we gave no
time to the WLAN context, which is OK unless
we are scanning, which always happens on the
WLAN context. Fix this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When sysassert happen, uCode will report the error code,
driver dump the information to dmesg. Here also remember
the last error code for future reference.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>