Its meaning is to limit amount of error messages to be printed out when buffer
mismatch is occured.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The following command should return actual state of the test.
	% cat /sys/kernel/debug/dmatest/run

To wait for test done the user may perform a busy loop that checks the state.
	% while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ]
	> do
	> 	echo -n "."
	> 	sleep 1
	> done
	> echo
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Instead of doing
	modprobe dmatest ...
	modprobe -r dmatest
we allow user to run tests interactively.

The dmatest could be built as module or inside kernel. Let's consider those
cases.

1. When dmatest is built as a module...

After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest
folder with nodes will be created. They are the same as module parameters with
addition of the 'run' node that controls run and stop phases of the test.

Note that in this case test will not run on load automatically.

Example of usage:
	% echo dma0chan0 > /sys/kernel/debug/dmatest/channel
	% echo 2000 > /sys/kernel/debug/dmatest/timeout
	% echo 1 > /sys/kernel/debug/dmatest/iterations
	% echo 1 > /sys/kernel/debug/dmatest/run

After a while you will start to get messages about current status or error like
in the original code.

Note that running a new test will stop any in progress test.

2. When built-in in the kernel...

The module parameters that is supplied to the kernel command line will be used
for the first performed test. After user gets a control, the test could be
interrupted or re-run with same or different parameters. For the details see
the above section "1. When dmatest is built as a module..."

In both cases the module parameters are used as initial values for the test case.
You always could check them at run-time by running
	% grep -H . /sys/module/dmatest/parameters/*
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Better to keep test parameters separate from internal variables.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

We don't need to have them global and later we would like to protect access to
them as well.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The proposed change will remove usage of the module parameters as global
variables. In future it helps to run different test cases sequentially.

The patch introduces the run_threaded_test() and stop_threaded_test() functions
that could be used later outside of dmatest_init, dmatest_exit scope.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

This will help in future to hide a global variable usage.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

If user have the timeout alike issues and wants to cancel the thread
immediately, the current call of wait_event_freezable_timeout is preventing to
this until timeout is expired. Thus, user will experience the unnecessary
delays.

Adding kthread_should_stop() check inside wait_event_freezable_timeout() solves
that.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Looks like only the RAID channels are allowed to have irq coalescing support
in the existing code. Fixing that. The ioat3 cleanup code can handle memcpy
ops anyways
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Acked-by: NDan Williams <djbw@fb.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Making OP field a hex instead of integer to make it more readable. Also add
the dump out of the NEXT field.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Acked-by: NDan Williams <djbw@fb.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Removing the annotation with __exit and referencing with __exit_p()
present in dma driver module remove hooks.

Part of the __devexit and __devexit_p() purge.
Signed-off-by: NMaxin B. John <maxin.john@enea.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Fix this compiler warning:
warning: 'td_remove' defined but not used [-Wunused-function]
Signed-off-by: NMaxin B. John <maxin.john@enea.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

pdc_desc_get() is called from pd_prep_slave_sg, and the function is
called from interrupt context(e.g. Uart driver "pch_uart.c").
In fact, I saw kernel error message.
So, GFP_ATOMIC must be used not GFP_NOIO.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Fix the logic to allow mc programming of second transfer after first
has been done, by removing immediate return upon success and iterating
until we detect QFull or DMAC dying.
Reported-by: NAlvaro Moran <dirac3000@gmail.com>
Tested-by: NAlvaro Moran <dirac3000@gmail.com>
Signed-off-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Flush lazy MMU when DEBUG_PAGEALLOC is set
  x86/mm/cpa/selftest: Fix false positive in CPA self test
  x86/mm/cpa: Convert noop to functional fix
  x86, mm: Patch out arch_flush_lazy_mmu_mode() when running on bare metal
  x86, mm, paravirt: Fix vmalloc_fault oops during lazy MMU updates

Pull scheduler fixes from Ingo Molnar:
 "Misc fixlets"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cputime: Fix accounting on multi-threaded processes
  sched/debug: Fix sd->*_idx limit range avoiding overflow
  sched_clock: Prevent 64bit inatomicity on 32bit systems
  sched: Convert BUG_ON()s in try_to_wake_up_local() to WARN_ON_ONCE()s

Pull perf fixes from Ingo Molnar:
 "Misc fixlets"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix error return code
  ftrace: Fix strncpy() use, use strlcpy() instead of strncpy()
  perf: Fix strncpy() use, use strlcpy() instead of strncpy()
  perf: Fix strncpy() use, always make sure it's NUL terminated
  perf: Fix ring_buffer perf_output_space() boundary calculation
  perf/x86: Fix uninitialized pt_regs in intel_pmu_drain_bts_buffer()

Pull drm fixes from Dave Airlie:
 "One fix for a hotplug locking regressions, and one fix for an oops if
  you unplug the monitor at an inopportune moment on the udl device."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/fb-helper: Fix locking in drm_fb_helper_hotplug_event
  udl: handle EDID failure properly.

Pull m68knommu fix from Greg Ungerer:
 "This contains only a single compilation fix for ColdFire m68k targets
  that use local non-GPIOLIB support."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: define a local gpio_request_one() function

Pull watchdog fix from Wim Van Sebroeck:
 "It will fix compile errors for the at91rm9200_wdt driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: Revert the AT91RM9200_WATCHDOG dependency

Pull one more btrfs fix from Chris Mason:
 "This has a recent fix from Josef for our tree log replay code.  It
  fixes problems where the inode counter for the number of bytes in the
  file wasn't getting updated properly during fsync replay.

  The commit did get rebased this morning, but it was only to clean up
  the subject line.  The code hasn't changed."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: make sure nbytes are right after log replay

Merge tag 'trace-fixes-v3.9-rc-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull ftrace fixes from Steven Rostedt:
 "Namhyung Kim found and fixed a bug that can crash the kernel by simply
  doing: echo 1234 | tee -a /sys/kernel/debug/tracing/set_ftrace_pid

  Luckily, this can only be done by root, but still is a nasty bug."

* tag 'trace-fixes-v3.9-rc-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Move ftrace_filter_lseek out of CONFIG_DYNAMIC_FTRACE section
  tracing: Fix possible NULL pointer dereferences

Nothing is using it yet, but this will allow us to delay the open-time
checks to use time, without breaking the normal UNIX permission
semantics where permissions are determined by the opener (and the file
descriptor can then be passed to a different process, or the process can
drop capabilities).
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Compiling the at91rm9200_wdt.c driver without at91rm9200
support was leading to several errors:

drivers/built-in.o: In function `at91_wdt_close':
at91_adc.c:(.text+0xc9fe4): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91_wdt_write':
at91_adc.c:(.text+0xca004): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91wdt_shutdown':
at91_adc.c:(.text+0xca01c): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91wdt_suspend':
at91_adc.c:(.text+0xca038): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91_wdt_open':
at91_adc.c:(.text+0xca0cc): undefined reference to `at91_st_base'
drivers/built-in.o:at91_adc.c:(.text+0xca2c8): more undefined references to
`at91_st_base' follow

So, reverting the modification of the "depends" Kconfig line
introduced by patch a6a1bcd3 (watchdog: at91rm9200: add DT support)
seems to be the good solution.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Revert commit 62a3ddef ("vfs: fix spinning prevention in prune_icache_sb").

This commit doesn't look right: since we are looking at the tail of the
list (sb->s_inode_lru.prev) if we want to skip an inode, we should put
it back at the head of the list instead of the tail, otherwise we will
keep spinning on it.

Discovered when investigating why prune_icache_sb came top in perf
reports of a swapping load.
Signed-off-by: NSuleiman Souhlal <suleiman@google.com>
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Anatol Pomozov identified a race condition that hits module unloading
and re-loading.  To quote Anatol:

 "This is a race codition that exists between kset_find_obj() and
  kobject_put().  kset_find_obj() might return kobject that has refcount
  equal to 0 if this kobject is freeing by kobject_put() in other
  thread.

  Here is timeline for the crash in case if kset_find_obj() searches for
  an object tht nobody holds and other thread is doing kobject_put() on
  the same kobject:

    THREAD A (calls kset_find_obj())     THREAD B (calls kobject_put())
    splin_lock()
                                         atomic_dec_return(kobj->kref), counter gets zero here
                                         ... starts kobject cleanup ....
                                         spin_lock() // WAIT thread A in kobj_kset_leave()
    iterate over kset->list
    atomic_inc(kobj->kref) (counter becomes 1)
    spin_unlock()
                                         spin_lock() // taken
                                         // it does not know that thread A increased counter so it
                                         remove obj from list
                                         spin_unlock()
                                         vfree(module) // frees module object with containing kobj

    // kobj points to freed memory area!!
    kobject_put(kobj) // OOPS!!!!

  The race above happens because module.c tries to use kset_find_obj()
  when somebody unloads module.  The module.c code was introduced in
  commit 6494a93d"

Anatol supplied a patch specific for module.c that worked around the
problem by simply not using kset_find_obj() at all, but rather than make
a local band-aid, this just fixes kset_find_obj() to be thread-safe
using the proper model of refusing the get a new reference if the
refcount has already dropped to zero.

See examples of this proper refcount handling not only in the kref
documentation, but in various other equivalent uses of this pattern by
grepping for atomic_inc_not_zero().

[ Side note: the module race does indicate that module loading and
  unloading is not properly serialized wrt sysfs information using the
  module mutex.  That may require further thought, but this is the
  correct fix at the kobject layer regardless. ]
Reported-analyzed-and-tested-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While trying to track down a tree log replay bug I noticed that fsck was always
complaining about nbytes not being right for our fsynced file.  That is because
the new fsync stuff doesn't wait for ordered extents to complete, so the inodes
nbytes are not necessarily updated properly when we log it.  So to fix this we
need to set nbytes to whatever it is on the inode that is on disk, so when we
replay the extents we can just add the bytes that are being added as we replay
the extent.  This makes it work for the case that we have the wrong nbytes or
the case that we logged everything and nbytes is actually correct.  With this
I'm no longer getting nbytes errors out of btrfsck.

Cc: stable@vger.kernel.org
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This patch attempts to fix:

	https://bugzilla.kernel.org/show_bug.cgi?id=56461

The symptom is a crash and messages like this:

	chrome: Corrupted page table at address 34a03000
	*pdpt = 0000000000000000 *pde = 0000000000000000
	Bad pagetable: 000f [#1] PREEMPT SMP

Ingo guesses this got introduced by commit 611ae8e3 ("x86/tlb:
enable tlb flush range support for x86") since that code started to free
unused pagetables.

On x86-32 PAE kernels, that new code has the potential to free an entire
PMD page and will clear one of the four page-directory-pointer-table
(aka pgd_t entries).

The hardware aggressively "caches" these top-level entries and invlpg
does not actually affect the CPU's copy.  If we clear one we *HAVE* to
do a full TLB flush, otherwise we might continue using a freed pmd page.
(note, we do this properly on the population side in pud_populate()).

This patch tracks whenever we clear one of these entries in the 'struct
mmu_gather', and ensures that we follow up with a full tlb flush.

BTW, I disassembled and checked that:

	if (tlb->fullmm == 0)
and
	if (!tlb->fullmm && !tlb->need_flush_all)

generate essentially the same code, so there should be zero impact there
to the !PAE case.
Signed-off-by: NDave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Artem S Tashkinov <t.artem@mailcity.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are remaining target-pending items for v3.9-rc7 code.

  The tcm_vhost patches are more than I'd usually include in a -rc7
  pull, but are changes required for v3.9 to work correctly with the
  pending vhost-scsi-pci QEMU upstream series merge.  (Paolo CC'ed)

  Plus Asias's conversion to use vhost_virtqueue->private_data + RCU for
  managing vhost-scsi endpoints has gotten alot of review + testing over
  the past weeks, and MST has ACKed the full series.

  Also, there is a target patch to fix a long-standing bug within
  control CDB handling with Standby/Offline/Transition ALUA port access
  states, that had been incorrectly rejecting the control CDBs required
  for LUN scan to work during these port group states.  CC'ing to
  stable."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Fix incorrect fallthrough of ALUA Standby/Offline/Transition CDBs
  tcm_vhost: Send bad target to guest when cmd fails
  tcm_vhost: Add vhost_scsi_send_bad_target() helper
  tcm_vhost: Fix tv_cmd leak in vhost_scsi_handle_vq
  tcm_vhost: Remove double check of response
  tcm_vhost: Initialize vq->last_used_idx when set endpoint
  tcm_vhost: Use vq->private_data to indicate if the endpoint is setup
  tcm_vhost: Use ACCESS_ONCE for vs->vs_tpg[target] access

Pull SCSI fixes from James Bottomley:
 "This is a set of ten bug fixes (and two consisting of copyright year
  update and version number change) pretty much all of which involve
  either a crash or a hang except the removal of the random sleep from
  the qla2xxx driver (which is a coding error so bad, we want it gone
  before anyone has a chance to copy it)."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] lpfc: fix potential NULL pointer dereference in lpfc_sli4_rq_put()
  [SCSI] libsas: fix handling vacant phy in sas_set_ex_phy()
  [SCSI] ibmvscsi: Fix slave_configure deadlock
  [SCSI] qla2xxx: Update the driver version to 8.04.00.13-k.
  [SCSI] qla2xxx: Remove debug code that msleeps for random duration.
  [SCSI] qla2xxx: Update copyright dates information in LICENSE.qla2xxx file.
  [SCSI] qla2xxx: Fix crash during firmware dump procedure.
  [SCSI] Revert "qla2xxx: Add setting of driver version string for vendor application."
  [SCSI] ipr: dlpar failed when adding an adapter back
  [SCSI] ipr: fix addition of abort command to HRRQ free queue
  [SCSI] st: Take additional queue ref in st_probe
  [SCSI] libsas: use right function to alloc smp response
  [SCSI] ipr: ipr_test_msi() fails when running with msi-x enabled adapter

Pull CIFS fix from Steve French:
 "Fixes a regression in cifs in which a password which begins with a
  comma is parsed incorrectly as a blank password"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Allow passwords which begin with a delimitor

As ftrace_filter_lseek is now used with ftrace_pid_fops, it needs to
be moved out of the #ifdef CONFIG_DYNAMIC_FTRACE section as the
ftrace_pid_fops is defined when DYNAMIC_FTRACE is not.

Cc: stable@vger.kernel.org
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Currently set_ftrace_pid and set_graph_function files use seq_lseek
for their fops.  However seq_open() is called only for FMODE_READ in
the fops->open() so that if an user tries to seek one of those file
when she open it for writing, it sees NULL seq_file and then panic.

It can be easily reproduced with following command:

  $ cd /sys/kernel/debug/tracing
  $ echo 1234 | sudo tee -a set_ftrace_pid

In this example, GNU coreutils' tee opens the file with fopen(, "a")
and then the fopen() internally calls lseek().

Link: http://lkml.kernel.org/r/1365663302-2170-1-git-send-email-namhyung@kernel.org

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: NNamhyung Kim <namhyung@kernel.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Pull sound fixes from Takashi Iwai:
 "This contains a few small ASoC fixes (wm8903, wm5102, samsung-i2s,
  tegra, and soc-compress) and an endian fix for NI USB-audio devices,
  update for Mark's e-mail address.

  No scary changes, AFAIS."

* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  MAINTAINERS: Update e-mail address
  ASoC: wm5102: Correct lookup of arizona struct in SYSCLK event
  ASoC: wm8903: Fix the bypass to HP/LINEOUT when no DAC or ADC is running
  ALSA: usb-audio: fix endianness bug in snd_nativeinstruments_*
  ASoC: tegra: Don't claim to support PCM pause and resume
  ASoC: Samsung: set drvdata before adding secondary device
  ASoC: Samsung: return error if drvdata is not set
  ASoC: compress: Cancel delayed power down if needed
  ASoC: core: Fix to check return value of snd_soc_update_bits_locked()

Merge tag 'asoc-maintainers-v3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

MAINTAINERS: Update e-mail address

Update the e-mail address I use for subsystems.

Update the e-mail address I use for subsystems.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Merge tag 'asoc-v3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Updates for v3.9

A few updates, more than I'd like, fixing some relatively small issues
but mostly driver specific ones.  Nothing wildly exciting so if it
doesn't make v3.9 it won't be the end of the world but it'd be nice.

When CONFIG_DEBUG_PAGEALLOC is set page table updates made by
kernel_map_pages() are not made visible (via TLB flush)
immediately if lazy MMU is on. In environments that support lazy
MMU (e.g. Xen) this may lead to fatal page faults, for example,
when zap_pte_range() needs to allocate pages in
__tlb_remove_page() -> tlb_next_batch().
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: konrad.wilk@oracle.com
Link: http://lkml.kernel.org/r/1365703192-2089-1-git-send-email-boris.ostrovsky@oracle.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

If the pmd is not present, _PAGE_PSE will not be set anymore.
Fix the false positive.
Reported-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1365687369-30802-1-git-send-email-aarcange@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>