HDMI 1.3 defines single link clocks up to 340 Mhz.
Refine the current dual link checks to only enable
dual link for DVI > 165 Mhz or HDMI > 340 Mhz if the
hw supports HDMI 1.3 (DCE3+).

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=44755Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We really only need to set it up once on init or resume
rather than on every mode set.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If the bpc is set from the connector is 0, we then use it later to adjust
in a special case the HDMI pixel clock, however if the bpc is 0, we end up
passing a 0 pixel clock into the code.

I'm not sure if this is the correct answer or if we should avoid the HDMI
clock adjustment for 0 values.

This fixes a divide by 0 on my Llano system with a HDMI monitor and hdmi
audio enabled.
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise each driver would need to keep the information inside
their own framebuffer object structure. Also add offsets[]. BOs
on the other hand are driver specific, so those can be kept in
driver specific structures.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43191Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's already called via the DPMS functions.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DP MST is DP multi-stream support, part of DP 1.2.

v2: switch to a helper macro as suggested by Michel.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Return the encoder id rather than a boolean.  This is needed
for differentiate between multiple DP bridge chips.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The logic was messy and hard to follow.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's handled via external clock.  It should already be protected
by the external ss flag, but add an explicit check just in case.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

v6 of the structure was programmed incorrectly:

  args.v6.ulCrtcPclkFreq.ulPixelClock = cpu_to_le32(clock / 10);

ulPixelClock is a 24-bit bitfield. This statement would thus
do a 32-bit swap of (clock / 10) and drop the top 8 bits which
are ... the LSB. Not what we want. Instead use masks & shifts.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Need to set the external transmitter type properly in
AdjustPixelClock to get the properly output.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise, no vblank interrupts.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=37522Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

For DP/eDP, always use the standard DP SS indices.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

If the ss clock is external, the CLK_REF bit needs to be set
in the SetPixelClock parameters.  This should fix DP failures
in the channel equalization loop.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Fusion hardware often has DP to VGA/LVDS/TMDS bridges to
handle non-DP encoders.  Internally we treat them mostly
like DP.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In DP mode, the DP ref clock can come from PPLL, DCPLL, or ext clock,
depending on the asic.  The crtc virtual pixel clock is derived from
the DP ref clock.

- DCE4: PPLL or ext clock
- DCE5: DCPLL or ext clock

Setting ATOM_PPLL_INVALID will cause SetPixelClock to skip
PPLL/DCPLL programming and only program the DP DTO for the
crtc virtual pixel clock.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- properly mask the ss type
- don't enable ss if type is external or percentage is 0
- if ss enabled and type is external, set ref_div_src to ext clock
- prefer ASIC_INTERNAL_SS_ON_DP to LCD_Info SS_Id for eDP
- fix ss amount calculation
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prefer min m to max p only on pre-r7xx asics.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36197Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prefer minm over maxp.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=35994Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Avoid touching the flip setup regs while
acceleration is running.  Set them at modeset
rather than during pageflip.  Touching these
regs while acceleration is active caused hangs
on pre-avivo chips.  These chips do not seem
to be affected, but better safe than sorry,
plus it avoids repeatedly reprogramming the
regs every flip.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

ntsc seems to work fine with either algo, some
pal TVs seem pickier.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=30832Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Typo in the aspect scale setup.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

... and switch it to container_of upcasting.

v2: converted new pageflip code-paths.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+.  Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.

v2: testing options

v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852
https://bugzilla.kernel.org/show_bug.cgi?id=24462
https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

agd5f: additional cleanups/fixes
Signed-off-by: NCédric Cano <ccano@interfaceconcept.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

New algo is used for r5xx+ and legacy is used for
r1xx-r4xx, rv515.

I've tested on all relevant GPUs and monitors that I
have access to and have found no problems.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=26562
https://bugzilla.kernel.org/show_bug.cgi?id=26552
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=32556Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Based on the vbios code.  This should hopefully
fix the pll problems on a number of avivo asics
once it's enabled.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

R6xx+ have per-block swappers.  BE content in the
framebuffer will now be swapped properly during scanout.
Untested, however, the same code is reported working in
the UMS ddx.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed.  Re-program
the mode first, then reset the dpms state.

This fixes the infamous atombios timeouts on resume.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Seems to cause problems on certain laptops

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=24462Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Tested-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The enter argument as implemented by commit 413d45d3 (drm, kdb, kms:
Add an enter argument to mode_set_base_atomic() API) should be more
descriptive as to what it does vs just passing 1 and 0 around.

There is no runtime behavior change as a result of this patch.
Reported-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: NDave Airlie <airlied@redhat.com>