scaler_id may be negative as shown by conditions later in the function,
so don't use it as an array index in that case.

v2:
- Remove ps_ctrl while at it (Ville).
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-2-git-send-email-imre.deak@intel.com

Following a GPU hang, we break out of the request loop in order to
unlock the struct_mutex for use by the GPU reset. However, if we retire
all the requests at that moment, we cannot identify the guilty request
after performing the reset.

v2: Not automatically retiring requests forces us to recheck for
available ringspace.

Fixes: f4457ae7 ("drm/i915: Prevent leaking of -EIO from i915_wait_request()")
Testcase: igt/gem_reset_stats/ban-*
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-4-git-send-email-chris@chris-wilson.co.uk

In order to reduce the workload of the caller, we do not want to
actually have to retire requests of others when checking the busy status
of this object. This applies to both busy/wait ioctls as the wait ioctl
has a semantically equivalent mode to the busy ioctl.

At the present time, this is only a minor improvement to reduce the
workload of the busy ioctl under the struct_mutex which helps to reduce
its impact upon contention of struct_mutex. However, since it is mostly
a victim in highly contended scenarios, the impact is very minor until
we can eliminate the struct_mutex requirement for busy-ioctl in the near
future.

v2: Mention the patches intended limited impact. It is just paving the
way for greater changes whilst reducing the impact of a bugfix in the
next patch.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-3-git-send-email-chris@chris-wilson.co.uk

The get-reset-stats ioctls wasn't waiting for a pending reset before
reporting its statistics, and so was ignoring a hang generated by the
context that should have been reported against said context.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-2-git-send-email-chris@chris-wilson.co.uk

The get-reset-stats ioctl reports upon the statistics (number of hangs,
be it as a victim or the guilty party) of a particular context. It is
semantically better as being part of i915_gem_context.c user interface,
as opposed to the hardware level access of intel_uncore.c
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-1-git-send-email-chris@chris-wilson.co.uk

The coding style documentation says the following about typedefs:

"In general, a pointer, or a struct that has elements that can
reasonably be directly accessed should _never_ be a typedef."

intel_limit_t falls in that category, so just use "struct intel_limit"
instead.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-3-git-send-email-ander.conselvan.de.oliveira@intel.com

Those are only used for defining struct intel_limit, so use anonymous
structs instead.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-2-git-send-email-ander.conselvan.de.oliveira@intel.com

Just use "struct dpll" everywhere. That's actually shorter than
intel_clock_t.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-1-git-send-email-ander.conselvan.de.oliveira@intel.com

Issue: VIZ-7772
Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Reviewed-by: peter.antoine@intel.com
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462531373-34819-2-git-send-email-nicholas.hoath@intel.com

Load guc firmware from file with major_minor number
in filename instead of using symolic link with only
major number.

This change is so that new firmwares can only be used
with a kernel change. This in case there is a regression
with a new firmware, it won't be used by default without
some testing.

Issue: VIZ-7713
Signed-off-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: peter.antoine@intel.com
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Another day, another long overdue conversion. Not much to update inside
intel_overlay.c, but still

   text	   data	    bss	    dec	    hex	filename
6309547	3578778	 696320	10584645	 a18245	vmlinux
6309291	3578778	 696320	10584389	 a18145	vmlinux

a couple of hundred bytes of pointer misdirection.

Whilst here, rename the ioctl entry points to include the _ioctl suffix
so that the user entry points are clear (following the idiom).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463053403-25086-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

SKL DPLLs shouldn't be called DPPLs.

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 2edd6443 ("drm/i915: Use a table to initilize shared dplls")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462993473-8254-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>

To be used for more efficient Gen range checking.

v2: Remove spurious chunk. (Chris Wilson)
v3: Rebase.
v4: Renamed from INTEL_GEN_RANGE and added GEN_FOREVER.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462874228-6601-1-git-send-email-tvrtko.ursulin@linux.intel.com

It just makes more work for the compiler and generates more code.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

This way optimization from a previous patch works even better.

v2: Rebase.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>

If we allow it a dedicated flag in dev_priv we enable the
compiler to nicely optimize conditions like IS_HASSWELL ||
IS_BROADWELL.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

If instead of numerical comparison me make these test a
bitmask, we enable the compiler to optimize all instances
of IS_GENx || IS_GENy.

v2: Make bit zero of gen mask mean gen 1.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Pass drm_i915_private to the uncore init/fini routines and their
subservients as it is their native type.

   text    data     bss     dec     hex filename
6309978 3578778  696320 10585076         a183f4 vmlinux
6309530 3578778  696320 10584628         a18234 vmlinux

a modest 400 bytes of saving, but 60 lines of code deleted!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462885804-26750-1-git-send-email-chris@chris-wilson.co.uk

Move the intel_enable_gtt() call to happen before we touch the GTT
during resume. Right now it's done way too late. Before
commit ebb7c78d ("agp/intel-gtt: Only register fake agp driver for gen1")
it was actually done earlier on account of also getting called from
the resume hook of the fake agp driver. With the fake agp driver
no longer getting registered we must move the call up.

The symptoms I've seen on my 830 machine include lowmem corruption,
other kinds of memory corruption, and straight up hung machine during
or just after resume. Not really sure what causes the memory corruption,
but so far I've not seen any with this fix.

I think we shouldn't really need to call this during init, but we have
been doing that so I've decided to keep the call. However moving that
call earlier could be prudent as well. Doing it right after the
intel-gtt probe seems appropriate.

Also tested this on 946gz,elk,ilk and all seemed quite happy with
this change.

v2: Reorder init_hw vs. enable_hw functions (Chris)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: ebb7c78d ("agp/intel-gtt: Only register fake agp driver for gen1")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462559755-353-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

arch/x86/kernel/early-quirks.c: In function ‘intel_graphics_stolen’:
arch/x86/kernel/early-quirks.c:539:9: warning: format ‘%llx’ expects
argument of type ‘long long unsigned int’, but argument 2 has type ‘phys_addr_t’ [-Wformat=]
         "0x%llx-0x%llx\n", base, base + size - 1);
         ^
arch/x86/kernel/early-quirks.c:539:9: warning: format ‘%llx’ expects
argument of type ‘long long unsigned int’, but argument 3 has type ‘phys_addr_t’ [-Wformat=]

v2: Use %pa for addresses

Fixes: ee0629cf (drm/i915: Function per early graphics quirk)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v1
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462811982-1567-1-git-send-email-chris@chris-wilson.co.uk

When the crtc is enabled but !active, we should still compute the
watermarks as if the planes were visible. That would make it more
likely that the we can later transition to active without errors.

Add a FIXME to remind people that we're doing the wrong thing now.
We should perhaps just move the wm computation for each individual plane
into the .check_plane hook, and later we'd just combine the results from
all active planes.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461940278-17122-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Use the cdclk we're going to be using when the pipe gets enabled to
compute the IPS linetime watermark. The current cdclk frequency is
irrelevant at this point since it can still change.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461940278-17122-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

   text	   data	    bss	    dec	    hex	filename
6309351	3578714	 696320	10584385	 a18141	vmlinux
6308391	3578714	 696320	10583425	 a17d81	vmlinux

Almost 1KiB of code reduction.

v2: More s/INTEL_INFO()->gen/INTEL_GEN()/ and IS_GENx() conversions

   text	   data	    bss	    dec	    hex	filename
6304579	3578778	 696320	10579677	 a16edd	vmlinux
6303427	3578778	 696320	10578525	 a16a5d	vmlinux

Now over 1KiB!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462545621-30125-3-git-send-email-chris@chris-wilson.co.uk

Move all of the constant assignments up front and into a common
function. This is primarily to ensure the backpointers are set as early
as possible for later use during initialisation.

v2: Use a constant struct so that all the similar values are set
together.
v3: Sanitize the engine's IMR to disable any potential interrupt before
we are ready (enabled in init_hw).
v4: Ignore the engine's IMR, to be resolved later
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462545621-30125-2-git-send-email-chris@chris-wilson.co.uk

I have noticed some of our interrupt handlers use both dev and
dev_priv while they could get away with only dev_priv in the
huge majority of cases.

Tidying that up had a cascading effect on changing functions
prototypes, so relatively big churn factor, but I think it is
for the better.

For example even where changes cascade out of i915_irq.c, for
functions prefixed with intel_, genX_ or <plat>_, it makes more
sense to take dev_priv directly anyway.

This allows us to eliminate local variables and intermixed usage
of dev and dev_priv where only one is good enough.

End result is shrinkage of both source and the resulting binary.

i915.ko:

 - .text         000b0899
 + .text         000b0619

Or if we look at the Gen8 display irq chain:

 -00000000000006ad t gen8_irq_handler
 +0000000000000663 t gen8_irq_handler
   -0000000000000028 T intel_opregion_asle_intr
   +0000000000000024 T intel_opregion_asle_intr
   -000000000000008c t ilk_hpd_irq_handler
   +000000000000007f t ilk_hpd_irq_handler
   -0000000000000116 T intel_check_page_flip
   +0000000000000112 T intel_check_page_flip
   -000000000000011a T intel_prepare_page_flip
   +0000000000000119 T intel_prepare_page_flip
   -0000000000000014 T intel_finish_page_flip_plane
   +0000000000000013 T intel_finish_page_flip_plane
   -0000000000000053 t hsw_pipe_crc_irq_handler
   +000000000000004c t hsw_pipe_crc_irq_handler
   -000000000000022e t cpt_irq_handler
   +0000000000000213 t cpt_irq_handler

So small shrinkage but it is all fast paths so doesn't harm.

Situation is similar in other interrupt handlers as well.

v2: Tidy intel_queue_rps_boost_for_request as well. (Chris Wilson)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.

v2: Deal with VBT code reorganization
    Deal with DRM_DP_DUAL_MODE_UNKNOWN
    Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
    Accept both DP and HDMI dvo_port in VBT as my BSW
    at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)

Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Reported-by: NTore Anderson <tore@fud.no>
Fixes: 7a0baa62 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>

To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.

v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
    helper getting passed the type, we wouldn't actually have to
    check at all in the driver, but the check eliminates the debug
    output more honest

Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>

Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.

Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.

Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.

v2: Store adaptor type under indel_hdmi->dp_dual_mode
    Deal with DRM_DP_DUAL_MODE_UNKNOWN
    Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
    and use it for type1 adaptors as well

Cc: stable@vger.kernel.org
Reported-by: NTore Anderson <tore@fud.no>
Fixes: 7a0baa62 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>

Add a helper which aids in the identification of DP dual mode
(aka. DP++) adaptors. There are several types of adaptors
specified: type 1 DVI, type 1 HDMI, type 2 DVI, type 2 HDMI

Type 1 adaptors have a max TMDS clock limit of 165MHz, type 2 adaptors
may go as high as 300MHz and they provide a register informing the
source device what the actual limit is. Supposedly also type 1 adaptors
may optionally implement this register. This TMDS clock limit is the
main reason why we need to identify these adaptors.

Type 1 adaptors provide access to their internal registers and the sink
DDC bus through I2C. Type 2 adaptors provide this access both via I2C
and I2C-over-AUX. A type 2 source device may choose to implement either
of these methods. If a source device implements the I2C-over-AUX
method, then the driver will obviously need specific support for such
adaptors since the port is driven like an HDMI port, but DDC
communication happes over the AUX channel.

This helper should be enough to identify the adaptor type (some
type 1 DVI adaptors may be a slight exception) and the maximum TMDS
clock limit. Another feature that may be available is control over
the TMDS output buffers on the adaptor, possibly allowing for some
power saving when the TMDS link is down.

Other user controllable features that may be available in the adaptors
are downstream i2c bus speed control when using i2c-over-aux, and
some control over the CEC pin. I chose not to provide any helper
functions for those since I have no use for them in i915 at this time.
The rest of the registers in the adaptor are mostly just information,
eg. IEEE OUI, hardware and firmware revision, etc.

v2: Pass adaptor type to helper functions to ease driver implementation
    Fix a bunch of typoes (Paulo)
    Add DRM_DP_DUAL_MODE_UNKNOWN for the case where we don't (yet) know
    the type (Paulo)
    Reject 0x00 and 0xff DP_DUAL_MODE_MAX_TMDS_CLOCK values (Paulo)
    Adjust drm_dp_dual_mode_detect() type2 vs. type1 detection to
    ease future LSPCON enabling
    Remove the unused DP_DUAL_MODE_LAST_RESERVED define
v3: Fix kernel doc function argument descriptions (Jani)
    s/NONE/UNKNOWN/ in drm_dp_dual_mode_detect() docs
    Add kernel doc for enum drm_dp_dual_mode_type
    Actually build the docs
    Fix more typoes
v4: Adjust code indentation of type2 adaptor detection (Shashank)
    Add debug messages for failurs cases (Shashank)
v5: EXPORT_SYMBOL(drm_dp_dual_mode_read) (Paulo)

Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1462542412-25533-1-git-send-email-ville.syrjala@linux.intel.com

This makes it easier to debug issues like https://bugs.freedesktop.org/show_bug.cgi?id=93477Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Chris Wilson <|chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/843f4327-1574-cf8e-0776-adbb0d58c2c0@mblankhorst.nlReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit 3543995a.

I mixed up maintainers and thought Linus' ack was for the mfd tree.
But Lee Jones (the real maintainer) wants to merge this through the
mfd tree, so revert here.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Allowing register copies where the source and destination are both
whitelisted should be safe, and is useful.  For example, Mesa uses
this to load the command streamer math registers with data from the
pipeline statistics counters.

v2: Reject writes to OACONTROL (and reads as well :(
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v1
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1462521014-13595-1-git-send-email-chris@chris-wilson.co.uk

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Version 1.01.

This firmware is made for Kabylake platform so it doesn't
need the stepping workaround that we had before.

v2: Rebased on top of latest nightly with min version
    required change.
v3: With right CSR_VERSION (Patrik).

Cc: Christophe Prigent <christophe.prigent@intel.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com> (v1)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461707991-15336-1-git-send-email-rodrigo.vivi@intel.com

As i915_ppgtt_init() is not used outside of i915_gem_gtt.c we can make
it static.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1462443767-5194-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NMatthew Auld <matthew.auld@intel.com>

If the command parser is not active, then it is appropriate to report it
as operating at version 0 as no higher mode is supported. This greatly
simplifies userspace querying for the command parser as we then do not
need to second guess when it will be active (a mixture of module
parameters and generational support, which may change over time).

v2: s/comand/command/ misspelling in comment
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1462368336-21230-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

LPT is pch, so might run into the fdi bandwidth constraint (especially
since it has only 2 lanes). But right now we just force pipe_bpp back
to 24, resulting in a nice loop (which we bail out with a loud
WARN_ON). Fix this.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93477Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462264381-7573-1-git-send-email-daniel.vetter@ffwll.ch

Only has one user and is nothing more than a shim on top of
i915_vma_unbind, so let's just get rid of it.

Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Suggested-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461842691-27575-1-git-send-email-matthew.auld@intel.com

They use dev_priv exclusively so pass it in instead of dev
for smaller source and binary.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461844620-35360-1-git-send-email-tvrtko.ursulin@linux.intel.com

Right now MST audio is causing too many kernel panics to really keep
around in the kernel. On top of that, even after fixing said panics it's
still basically non-functional (at least on all the setups I've tested
it on). Revert until we have a proper solution for this.

This reverts commit 3d52ccf5.
Signed-off-by: NLyude <cpaul@redhat.com>
Fixes: 3d52ccf5 ("drm/i915: start adding dp mst audio")
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462287692-28570-1-git-send-email-cpaul@redhat.com