The state of the SDVO chip is more difficult to save than the LVDS so we do a
full mode set on the crtc to get SDVO operational again. The SDVOB/C register is
also stored just in case we have special bits set in the future.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

Currently we do whatever is done during suspend/resume but we might need some
more work for hibernation so keep them in separate functions.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

This patch activates the rebuilding of the gtt. Currently we reinitialize the
gtt by inserting the stolen pages again and map the rest to our scratch page.
Then we go about restoring the needed ranges. This is a bit overkill but right
now we don't have that much to restore so better safe than sorry.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

By having 'drm' and 'fb' in the fb screeninfo id, pm-utils will leave us
alone. Otherwise we'll have quirks up to our ears and resume will break.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

Both VGA and HDMI connectors are available on my Asus EeePC X101CH.
This patch will cause output to be shown on either when plugged in.
For both, it shows the leftmost 800x600, of the 1024x600 on LVDS.
Signed-off-by: NKero van Gelder <kero@chello.nl>
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

Remove unused defines that we'll never use and fix naming in some include guards
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

psb_intel_crtc_gamma_set() and psb_intel_crtc_destroy() aren't used outside of
psb_intel_display.c right now so no need to expose them.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

This makes it easier to read. We do the same for cdv so it becomes more
consistent as well.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

i9xx_clock() and i8xx_clock() did the same calc and psb_intel_clock() just
called i9xx_clock() so just move it all into psb_intel_clock().

The same calculation is duplicated in cdv_intel_display.c as well so maybe we
can share it later on.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

The use of pointer sender should be after the NULL check.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

Replaced calls kzalloc followed by memcpy with call to kmemdup.
Patch found using coccinelle.
Signed-off-by: NAlexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

commit f9f23a77(gma500: remove no_fb bits)
remove all the drm_psb_no_fb relations code in gma500 except this line code,
so remove it also.
Signed-off-by: NWang YanQing <udknight@gmail.com>
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>

[airlied: hack for now until we fix cma helpers on other OF platforms]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Thierry writes:
"Remove a duplicate implementation of the CEA VIC lookup and move the CEA
and other mode tables to drm_edid.c to make it more difficult to create
duplicates of the tables.

Add some helpers to pack CEA-861/HDMI AVI, audio and SPD infoframes into
binary buffers that can easily be written into hardware registers. A new
helper function makes it easy construct an AVI infoframe from a DRM
display mode.

Convert the Tegra and Radeon drivers to use the new HDMI helpers."
* 'drm/hdmi-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
  drm/radeon: Use generic HDMI infoframe helpers
  drm/tegra: Use generic HDMI infoframe helpers
  drm: Add EDID helper documentation
  drm: Add HDMI infoframe helpers
  video: Add generic HDMI infoframe helpers
  drm: Add some missing forward declarations
  drm: Move mode tables to drm_edid.c
  drm: Remove duplicate drm_mode_cea_vic()

Two regressions fixes from snowboarding land

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Revert hdmi HDP pin checks
  drm/i915: Handle untiled planes when computing their offsets

Thierry writes:
"Add support for 2 hardware overlays found on Tegra. These support YUV
pixel formats and can be used as video overlays. .mode_set_base() is
implemented and support for VBLANK and page-flipping is added.

A few minor bug fixes are also included and a new debugfs file allows
to inspect the framebuffers attached to the Tegra DRM device."

* 'drm/tegra-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
  drm/tegra: Add list of framebuffers to debugfs
  drm/tegra: Fix color expansion
  drm/tegra: Split DC_CMD_STATE_CONTROL register write
  drm/tegra: Implement page-flipping support
  drm/tegra: Implement VBLANK support
  drm/tegra: Implement .mode_set_base()
  drm/tegra: Add plane support
  drm/tegra: Remove bogus tegra_framebuffer structure
  drm: Add consistency check for page-flipping

This reverts

commit 8ec22b21
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri May 11 18:01:34 2012 +0100

    drm/i915/hdmi: Query the live connector status bit for G4x

and

commit b0ea7d37
Author: Damien Lespiau <damien.lespiau@intel.com>
Date:   Thu Dec 13 16:09:00 2012 +0000

    drm/i915/hdmi: Read the HPD status before trying to read the EDID

They reliably cause HDMI to not be detected on some systems (like my
ivb or the bug reporters gm45). To fix up the very slow unplug issues
we might want to fire up a 2nd detect cycle a few hundred ms after
each hotplug. But for now at least make displays work again.

I somewhat suspect that this is confined to HDMI connectors, since all
the machines I have with DP+ outputs work correctly.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52361
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org.kernel.org # for 8ec22b21Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This list is most useful to inspect whether framebuffer reference
counting works as expected. The code is loosely based on the i915
implementation.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

bpp stores the number of bytes per pixel, but color expansion needs to
be enabled for less than 24 bits per pixel.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

The Tegra TRM says that the ACT_REQ and UPDATE fields cannot be
programmed at the same time so they are updated in two consecutive
writes instead.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

All the necessary support bits like .mode_set_base() and VBLANK are now
available, so page-flipping case easily be implemented on top.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Implement support for the VBLANK IOCTL. Note that Tegra is somewhat
special in this case because it doesn't use the generic IRQ support
provided by the DRM core (DRIVER_HAVE_IRQ) but rather registers one
interrupt handler for each display controller.

While at it, clean up the way that interrupts are enabled to ensure
that the VBLANK interrupt only gets enabled when required.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

The sequence for replacing the scanout buffer is much shorter than a
full mode change operation so implementing this callback considerably
speeds up cases where only a new framebuffer is to be scanned out.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add support for the B and C planes which support RGB and YUV pixel
formats and can be used as overlays or hardware cursor. Currently 32-bit
XRGB as well as UYVY, YUV420 and YUV422 pixel formats are advertised.
Other formats should be easy to add but these are the most common ones
and should cover the majority of use-cases.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Tegra uses the CMA FB helpers so framebuffers passed to the driver need
to use the corresponding functions to access the underlying GEM objects.

This used to work because struct tegra_framebuffer was sufficiently
similar to struct drm_fb_cma but that isn't guaranteed to stay that way.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Driver implementations of the drm_crtc's .page_flip() function are
required to update the crtc->fb field on success to reflect that the new
framebuffer is now in use. This is important to keep reference counting
on the framebuffers balanced.

While at it, document this requirement to keep others from falling into
the same trap.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use the generic HDMI infoframe helpers to get rid of the duplicate
implementation in the radeon driver.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Use the generic HDMI infoframe helpers to get rid of the NVIDIA Tegra
reimplementation.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Add a reference section about the EDID helper functions to the DRM
documentation.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Add a generic helper to fill in an HDMI AVI infoframe with data
extracted from a DRM display mode.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Add generic helpers to pack HDMI infoframes into binary buffers.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The drm_file and drm_clip_rect structures are used throughout the file
but they are never declared nor pulled in through an include. Add
forward declarations to make them available.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The modes are only used from within drm_edid.c so we move them there to
avoid creating duplicates by multiple inclusion of drm_edid_modes.h. As
a side-effect we can also get rid of a few variables that keep track of
the number of entries in the tables and use ARRAY_SIZE() instead.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The same function had already been merged with a different name. Remove
the duplicate one but reuse some of its kerneldoc fragments for the
existing implementation.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

The summary:
. Add display mode check operaion to mixer driver
  - Mixer IP also can put certain restrictions on the proposed
    display modes and these restrictions need to be considered
    during mode negotiation, which happens immediately after
    edid parsing.
. Set correct mode for range of resolutions
  - With this patch, the mixer driver could find the correct mode
    for the range of resolutions upto 1080 vertical lines.
. Support extra resolution for hdmi
  - This patch programs the core and timing generator registers
    using the timing data provided in drm_display_mode without
    hard-coded configurations. So this patch adds additional PHY
    configs to allow us to support more permissible resolutions
    and refresh rates.
. Add device tree support for g2d
  - This patch adds just the compatible string for exynos5250 SoC
    so that with device tree enabling, this driver can be probed.
. And bug fixes and code cleanups.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: Add device tree based discovery support for G2D
  drm/exynos: hdmi: support extra resolutions using drm_display_mode timings
  drm/exynos: mixer: set correct mode for range of resolutions
  drm/exynos: implement display-mode-check callback in mixer driver
  drm/exynos: add display-mode-check operation to exynos_mixer_ops struct
  drm/exynos: release resources properly when fb creation is failed.
  drm/exynos: fix wrong pointer access at vm close.
  drm/exynos: Add missing braces around sizeof
  drm/exynos: consider exception case to fb handle creation
  drm/exynos: fix iommu address allocation order

The values of n, m1 and m2 needs to be subtracted by 2 before writing them to
the FP register. The dot clock calculation already thinks of these values in
register form so we must also specify them as such.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.

However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.

Fixes regression from commit c2c75131
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Jul 5 12:17:30 2012 +0200

    drm/i915: adjust framebuffer base address on gen4+

v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch adds device tree match table for Exynos G2D controller.
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>