Our hardware supports inserting a specified VLAN header for each
function when sending packets. User can enable it with command
"ip link set <devname> vf  <vfid> vlan <vlan id>".
For this VLAN header is inserted by hardware, not from stack,
hardware also needs to strip it from received packets before
sending to stack.  In this case, driver needs to tell
hardware which VLAN to insert or strip.

The current VLAN initialization doesn't allow inserting
VLAN header by hardware, this patch modifies it, in order be
compatible with VLAN inserted base on port.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit bfcb79fc
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.

This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.

This patch needs backporting to the kernel v5.0+

Fixes: 332fbf57 ("net: hns3: add handling of hw ras errors using new set of commands")
Reported-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver is unloading, if there is a calling of ndo_open occurs
between phy_disconnect() and unregister_netdev(), it will end up
causing the kernel to eventually hit a NULL deref:

[14942.417828] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000048
[14942.529878] Mem abort info:
[14942.551166]   ESR = 0x96000006
[14942.567070]   Exception class = DABT (current EL), IL = 32 bits
[14942.623081]   SET = 0, FnV = 0
[14942.639112]   EA = 0, S1PTW = 0
[14942.643628] Data abort info:
[14942.659227]   ISV = 0, ISS = 0x00000006
[14942.674870]   CM = 0, WnR = 0
[14942.679449] user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000224ad6ad
[14942.695595] [0000000000000048] pgd=00000021e6673003, pud=00000021dbf01003, pmd=0000000000000000
[14942.723163] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[14942.729358] Modules linked in: hns3(O) hclge(O) pv680_mii(O) hnae3(O) [last unloaded: hclge]
[14942.738907] CPU: 1 PID: 26629 Comm: kworker/u4:13 Tainted: G           O      4.18.0-rc1-12928-ga960791-dirty #145
[14942.749491] Hardware name: Huawei Technologies Co., Ltd. D05/D05, BIOS Hi1620 FPGA TB BOOT BIOS B763 08/17/2018
[14942.760392] Workqueue: events_power_efficient phy_state_machine
[14942.766644] pstate: 80c00009 (Nzcv daif +PAN +UAO)
[14942.771918] pc : test_and_set_bit+0x18/0x38
[14942.776589] lr : netif_carrier_off+0x24/0x70
[14942.781033] sp : ffff0000121abd20
[14942.784518] x29: ffff0000121abd20 x28: 0000000000000000
[14942.790208] x27: ffff0000164d3cd8 x26: ffff8021da68b7b8
[14942.795832] x25: 0000000000000000 x24: ffff8021eb407800
[14942.801445] x23: 0000000000000000 x22: 0000000000000000
[14942.807046] x21: 0000000000000001 x20: 0000000000000000
[14942.812672] x19: 0000000000000000 x18: ffff000009781708
[14942.818284] x17: 00000000004970e8 x16: ffff00000816ad48
[14942.823900] x15: 0000000000000000 x14: 0000000000000008
[14942.829528] x13: 0000000000000000 x12: 0000000000000f65
[14942.835149] x11: 0000000000000001 x10: 00000000000009d0
[14942.840753] x9 : ffff0000121abaa0 x8 : 0000000000000000
[14942.846360] x7 : ffff000009781708 x6 : 0000000000000003
[14942.851970] x5 : 0000000000000020 x4 : 0000000000000004
[14942.857575] x3 : 0000000000000002 x2 : 0000000000000001
[14942.863180] x1 : 0000000000000048 x0 : 0000000000000000
[14942.868875] Process kworker/u4:13 (pid: 26629, stack limit = 0x00000000c909dbf3)
[14942.876464] Call trace:
[14942.879200]  test_and_set_bit+0x18/0x38
[14942.883376]  phy_link_change+0x38/0x78
[14942.887378]  phy_state_machine+0x3dc/0x4f8
[14942.891968]  process_one_work+0x158/0x470
[14942.896223]  worker_thread+0x50/0x470
[14942.900219]  kthread+0x104/0x130
[14942.903905]  ret_from_fork+0x10/0x1c
[14942.907755] Code: d2800022 8b400c21 f9800031 9ac32044 (c85f7c22)
[14942.914185] ---[ end trace 968c9e12eb740b23 ]---

So this patch fixes it by modifying the timing to do phy_connect_direct()
and phy_disconnect().

Fixes: 256727da ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hnae3_register_ae_dev() may fail, and it should return a error code
to its caller, so change hnae3_register_ae_dev() return type to int.

Also, when hnae3_register_ae_dev() return error, hns3_probe() should
do some error handling and return the error code.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After doing down/uninit/init/up in hclge_dcb, it is not necessary
to call dcb_ops->map_update in enet, so hclge_map_update can be
called directly in hclge_dcb.

This is for preparing to call hns3_nic_set_real_num_queue with
netdev down when user changes mqprio configuration.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently rss configuration set by user will be lost when setting
channel.

This patch fixes it by not setting rss configuration to default
if user has configured the rss.

Fixes: 09f2af64 ("net: hns3: add support to modify tqps number")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The HNAE3_INIT_CLIENT interface is also used when changing tc
configuration, vlan/mac hardware table does not need to be restored
when tc configuration changes.

This patch adds a HNAE3_RESTORE_CLIENT interface to restore the
vlan/mac hardware table when resetting.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool -L option with the combined parameter is for changing the number of
multi-purpose channels of the specified network device. Under the current
scheme, the user configuration information will be lost after the reset or
TC information changed.

This patch fixes this issue. By default, this configuration is set to the
minimum between the number of queues for each enabled TCs and the maximum
number support available in the hardware. When there is a user
configuration, regardless of the reset or TC information change, it should
keep the user's configuration while it is under the hardware limits,
otherwise set to the maximum number support available in the hardware.

Fixes: 09f2af64 ("net: hns3: add support to modify tqps number")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When triggering nic down, there is a time window between bringing down
the protocol stack and stopping the work task. If the net is up in the
time window, it may bring up the protocol stack again.

This patch fixes it by stop the work task at the beginning of
hns3_nic_net_stop(). To keep symmetrical, start the work task at the
end of hns3_nic_net_open().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints queue map information.

debugfs command:
echo dump queue map > cmd

Sample Command:
root@(none)# echo queue map > cmd
 local queue id | global queue id | vector id
          0              32             769
          1              33             770
          2              34             771
          3              35             772
          4              36             773
          5              37             774
          6              38             775
          7              39             776
          8              40             777
          9              41             778
         10              42             779
         11              43             780
         12              44             781
         13              45             782
         14              46             783
         15              47             784
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds handling for HNS3 hardware errors(non-standard)
which are reported through MSIX interrupts and not through
PCIe AER channel.

These MSIX reported hardware errors are handled using common
misc. interrupt handler. Hardware error related registers
cannot be cleared in context to the interrupt received as
they require *heavy* access to hardware using IMP(Integrated
Mangement Processor) commands. Hence, we defer the clearing
of such error events till later time.

Since, we have defered exact identification of errors we
will have to defer the level of receovery/reset which
might be required. Hence, a new reset type UNKNOWN reset
has been introduced which effectively defers the assertion
of the reset till we get hold of kind of errors at later
time.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch renames process_hw_error function to
handle_hw_ras_error function to match the purpose
of the function. This is because hw errors reported through
ras and msix interrupts will be handled separately.
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the Flow Director rules are stored in tcam blocks.
For each bit of tcam entry, the match value
depends on two input value(x, y).

debugfs command:
echo dump fd tcam > cmd

Sample output:
root@(none)# echo dump fd tcam > cmd
hns3 0000:7d:00.0: read result tcam key x(31):
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 08000000
hns3 0000:7d:00.0: 00000600
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: read result tcam key y(31):
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: f7ff0000
hns3 0000:7d:00.0: 0000f900
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 00000000
hns3 0000:7d:00.0: 0000fff8
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the debugfs framework to the driver and create a debugfs
command interface for each device.

example command:
"echo queue info > cmd" Query the packet forwarding queue information.
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.

This patch adds vport alive state checking support, in order
to support the above scenario.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support of ethtool -K to enable/disable
hardware GRO in HNS3 PF/VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 hardware Revision B(=0x21) supports Hardware GRO feature. This
patch enables this feature in the HNS3 PF/VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the .reset_prepare and .reset_done
ops from pci framework to support the PF FLR.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.

Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.

Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.

This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.

Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.

hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.

So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.

Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.

There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec399 ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the error recovery for the HNS hw errors.
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set of hw errors occurred in the HNS3 are reported to the
hns3 driver through PCIe AER and RAS.The error info will be
processed and appropriately recovered.
This patch adds error_detected callback and error processing.
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For mta table support has been dropped, remove the code for mta table.
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds switch for flow director with ethtool command
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for querying rule number and rule details
by ethtool commands.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for add and delete rule by ethtool commands.
HNS3 driver supports several flow types, include ETHER_FLOW,
IP_USER_FLOW, TCP_V4_FLOW, UDP_V4_FLOW, SCTP_V4_FLOW, IPV6_USER_FLOW,
TCP_V6_FLOW, UDP_V6_FLOW and SCTP_V6_FLOW.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds serdes parallel inner loopback support for self test.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In fact, our implementation of mac loopback is the implementation of app
loopback now. Current name is wrong. This patch renames mac loopback to
app loopback.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our loop mode includes mac loop, serdes loop and phy loop. Not all of them
are related with mac. This patch corrects their names.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>