Follow the convention of configuring padconf for all pins and not leaving
any 0x80000000 to leave them un-configured.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Use the gpio contants defined in bindings for active high/low
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Remove aliases that are either not used by bootloader or are provided via
included dtsi files.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The general device-tree rule is to not include nodes that do not have a driver
or bindings in a dts/dtsi. Remove the place-holder nodes from the Gateworks
Ventana boards until a time that a driver with proper bindings exists.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This alias is used by U-Boot to enable/disable the regulator depending
on baseboard type.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The spi-mxs driver does not allow full duplex SPI transfers. The
spi-gpio driver may be used as an alternative if this is required.

Make the choice between those drivers easier for the end user by
providing settings for both drivers.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The labels on the spidev nodes are not used and not required, so
remove them. The TX28 supports 3 chipselects on the SPI
interface. Make all those chipselects available to the user.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: NShengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: NShengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Passing '0x80000000' to the pin configuration means that kernel will skip the
IOMUXC_SW_PAD_CTL configuration and will use whathever values come from the
bootloader.

Instead of relying on the bootloader setup, let's configure it in the kernel to
have predictable settings.

'0x1b0b0' is the default POR value for all these pins and has also been verified
that the pins are using this value by manually inspecting the IOMUXC_SW_PAD_CTL
registers, so no functional change has been made.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the wa
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@02220000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:

device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"

Rename the child node name in order to avoid the warning.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add support for the "MX28LCD Seiko 4.3' WVGA" panel.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

imx6sx has the same LCDIF controller IP as in mx28, so add the proper
compatible strings.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Fixes "imx6q-pcie 1ffc000.pcie: missing *config* reg space"
error exposed by new versions of the designware pcie driver.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the i.MX1 APF9328 from Armadeus.
This change is intended to further remove non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add the IOMUX setting for the IR input, rather than relying on the
boot loader.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

HummingBoard after rev 2.0 and the production one starting rev 3.0 uses
gpio 3,5 (EIM_DA5 pad) as the gpio infra red receiver input.

Since the original Carrier1 board is obsolete and we are retiring it,
update the DT file for this.  This will mean IR reception will not
work on Carrier1 with this DT file.
Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Initial patch from Rabeeh, but with the electrical properties added.
Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The i.MX53 has a Cortex-A8 Performance Monitor Unit.

Add it to the dtsi.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds the battery backed real time clock connected to I2C1
to the device tree.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add support for the "MX28LCD Seiko 4.3' WVGA" panel.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Let's keep pinctrl nodes sorted.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add support for the Gateworks GW5520 board.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds simple-card support to the i.MX SoCs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the Freescale (Motorola) i.MX1 ADS board.
This change is intended to further remove non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add USB support for Freescale Vybrid tower. The USB hosts over-current
protection signal is not connected to the PHY's over- current
protection, hence we need to disable it.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add USB support for Colibri VF61 modules. The Colibri standard pinout
defines a pin for USB over-current. However, due to lack of pinmux
options, the USB hosts over-current protection signal of the Colibri
standard could not be connected to the PHY's over-current protection.
Hence we need to disable the over-current functionality of the USB
controller.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add device tree node for usbmisc which controls the non-core USB
registers. This is required to use the property to disable the over-
current detection.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This adds USB PHY and USB controller nodes. Vybrid SoCs have two
independent USB cores which each supports DR (dual role). However,
real OTG is not supported since the OTG ID pin is not available.

The PHYs are located within the anadig register range, hence we need
to change the length of the anadig registers.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>