It adds device tree support for imx53 boards.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
LAKML-Reference: 1301921449-32194-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Most machine files include "devices-imxXX.h" which in turn includes
<mach/devices-common.h>.  The latter already includes many headers
that the machine files don't need to include again.

These were found by:

 $ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile
 $ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F

(but I kept linux/init.h, linux/kernel.h and linux/platform_device.h)

LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

On mx53_smd board only RX/TX pins are used on UART2.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Fix UART1 IOMUX settings and configure UART1 to work with only RX/TX pins.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Commit 816ad741 (ARM: i.MX53: Add full iomux support for mx53) renamed some of the pad names.

Make the changes accordingly so that mx53_loco and mx53_cmd can build without errors.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

1. Add Kconfig and Makefile entries
2. Add board definition
3. enable uart and fec for SMD board
Signed-off-by: NYong Shen <yong.shen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>