Merge tag 'uniphier-dt64-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

UniPhier ARM64 SoC DT updates for v4.18

- add more properties to ethernet nodes

* tag 'uniphier-dt64-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: add syscon-phy-mode property to each ethernet node
  arm64: dts: uniphier: add clock-names and reset-names to ethernet node
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

UniPhier ARM SoC DT updates for v4.18

- add more properties to ethernet nodes

* tag 'uniphier-dt-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add syscon-phy-mode property to each ethernet node
  ARM: dts: uniphier: add required clocks and resets to Pro4 ethernet node
Signed-off-by: NOlof Johansson <olof@lixom.net>

mvebu dt64 for 4.18 (part 1)

 - Allow using Armada 3700 gpio controller as interrupt one too
 - Describe SPI flash on the EspressoBin
 - Mark ahci as dma-coherent for Armada 7K/8K
 - Add 10G interface support Armada 7K/8K based boards (including MacBin)

* tag 'mvebu-dt64-4.18-1' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: armada-37xx: mark the gpio controllers as irq controller
  arm64: dts: marvell: 7040-db: describe the 10G interface as fixed-link
  arm64: dts: marvell: 8040-db: describe the 10G interfaces as fixed-link
  arm64: dts: marvell: mcbin: enable the fourth network interface
  arm64: dts: marvell: mcbin: add 10G SFP support
  arm64: dts: marvell: mark CP110 ahci as dma-coherent
  arm64: dts: armada-3720-espressobin: wire up spi flash
Signed-off-by: NOlof Johansson <olof@lixom.net>

mvebu dt for 4.18 (part 1)

 - Update 32-bit Marvell EBU NAND DT nodes with new bindings
 - Add NAND pinctrl information for the Armada 98DX3236 and variants

* tag 'mvebu-dt-4.18-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: armada-xp-98dx: Add NAND pinctrl information
  ARM: dts: armada-39x: update NAND node with new bindings
  ARM: dts: armada-38x: update NAND node with new bindings
  ARM: dts: armada-375: update NAND node with new bindings
  ARM: dts: armada-370-xp: update NAND node with new bindings
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'tegra-for-4.18-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

ARM: tegra: Device tree changes for v4.18-rc1

Contains a fix for the high-speed UART on Toradex Apalis TK1 boards as
well as IOMMU enablement for various devices on Tegra30 and Tegra30.

* tag 'tegra-for-4.18-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: dts: tegra114: Add IOMMU nodes to Host1x and its clients
  ARM: dts: tegra30: Add IOMMU nodes to Host1x and its clients
  ARM: tegra: apalis-tk1: Fix high speed UART compatible
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'tegra-for-4.18-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

dt-bindings: tegra: Changes for v4.18-rc1

This contains the device tree bindings updates for the memory controller
hot resets that are implemented by driver patches in a different branch.

* tag 'tegra-for-4.18-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: Relocate Tegra20 memory controller bindings
  dt-bindings: arm: tegra: Document #reset-cells property of the Tegra20 MC
  dt-bindings: memory: tegra: Document #reset-cells property of the Tegra30 MC
  dt-bindings: arm: tegra: Remove duplicated Tegra30+ MC binding
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'davinci-for-v4.18/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

DaVinci device-tree updates for v4.18

* DA850 EVM gains USB support, SD card write-protect, card detect
  and some clean-up
* Support for gpio-ranges makes using gpios from DT much easier
* Lego EV3 clean-up

* tag 'davinci-for-v4.18/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-evm: add WP and CD to MMC
  ARM: dts: da850-lego-ev3: remove unnecessary gpio-keys properties
  ARM: dts: da850-evm: use phandles to extend nodes
  ARM: dts: da850: use gpio-ranges
  ARM: dts: da850-evm: Enable usb_phy, usb0 and usb1
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Amlogic 64-bit DT updates for v4.18
- AXG family: support more peripherals (wifi, eMMC, clocks)
- GX family: add/enable USB host support

* tag 'amlogic-dt64' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  dt-bindings: arm: amlogic: add support for the Tronsmart MXIII Plus
  dt-bindings: arm: amlogic: add support for the Meson8m2 SoC
  ARM64: dts: meson-axg: enable AP6255 wifi module
  ARM64: dts: meson: add MMC resets
  ARM64: dts: meson-axg: add an 32K alt aoclk
  ARM64: dts: meson-axg: add tdm pins
  ARM64: dts: meson-axg: add GPIO interrupt controller support
  ARM64: dts: meson-axg: enable the eMMC controller
  ARM64: dts: meson-gx: fix gxl clock controller compatible
  ARM64: dts: meson-axg: use hhi syscon for the clock controller
  ARM64: dts: meson-gx: sysctrl is the parent of the clock controller
  dt-bindings: clock: meson: update documentation with hhi syscon
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Amlogic 32-bit DT updates for v4.18
- add support for meson8m2 SoC
- new board: Tronsmart MXIII Plus using meson8m2 SoC
- odroid-c1: add IR

* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus
  ARM: dts: meson8: add the uart_A pins
  ARM: dts: meson: add support for the Meson8m2 SoC
  ARM: meson: add support for the Meson8m2 SoCs
  ARM: dts: meson8b: odroid-c1: enable the IR receiver
  ARM: dts: meson8b: odroid-c1: sort nodes alphabetically
  ARM: dts: meson8b: add the cortex-a5-pmu compatible PMU
  ARM: dts: meson8: add the cortex-a9-pmu compatible PMU
Signed-off-by: NOlof Johansson <olof@lixom.net>

ARM64: DT: Hisilicon SoC DT updates for 4.18v2

- Add mailbox, stub clock, CPU frequency scaling, thermal cooling
  management and pcie msi interruption support for hi3660
- Add LPC support for hip06 and hip07
- Add PCIe, usb and emmc support for hi3798cv200

* tag 'hisi-arm64-dt-for-4.18v2' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hi3798cv200: enable emmc support for poplar board
  arm64: dts: hi3798cv200: enable usb2 support for poplar board
  arm64: dts: hi3798cv200: enable PCIe support for poplar board
  arm64: dts: hisi: Enable Hisi LPC node for hip07
  arm64: dts: hisi: Enable Hisi LPC node for hip06
  arm64: dts: hi3660: Add pcie msi interrupt attribute
  arm64: dts: hi3660: Add thermal cooling management
  arm64: dts: hi3660: Add CPU frequency scaling support
  arm64: dts: hi3660: Add stub clock node
  arm64: dts: hi3660: Add mailbox node
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add pin control information for the NAND interface on the Armada
98DX3236 and variants.
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.

Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.

Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.

Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.

Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

This allows to reference these gpio controller as interrupt parent. Also
add a comment which cpu line names are managed by the controllers
because "nb" and "sb" usually doesn't appear in schematics, but MPPX_Y
do.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

This patch adds a fixed-link node to the 10G interface of the 7040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cage but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

This patch adds a fixed-link node to both 10G interfaces of the 8040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cages but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

This patch enables the fourth network interface on the Marvell
Macchiatobin. It is configured in the 2500Base-X PHY mode. The SFP cage
is also described.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

This patch adds the SFP cage description in the Marvell Armada 8040
mcbin, for both 10G interfaces.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
[Antoine: small reworks, commit message]
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

The legacy mode uses the write protect and card detect but DT does not.
This patch enables Write-Protect and Card-Detect pins for the MMC card, and
the gpio-ranges property sets the gpio pinmuxing for those respective pins.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Merge tag 'v4.18-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

All iommus got their clocks added and rk3399 got support for its
usb3-phy otg-port and better ajustment for the cpll child clocks.
On the board side, all rk3399 got their typec phys enabled - which
is needed for better usb support, the sapphire board got some more
properties moved to the excavator baseboard where they really belong,
kevin got a fix to use a real devicetree compatible and puma-haikou
got its hdmi port enabled.

* tag 'v4.18-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: enable hdmi on rk3399-puma-haikou
  arm64: dts: rockchip: use canonical compatible for touchpad/touchscreen on gru-kevin
  arm64: dts: rockchip: add clocks in iommu nodes
  arm64: dts: rockchip: add usb3-phy otg-port support for rk3399
  arm64: dts: rockchip: remove PCIe assigned-clocks in excavator baseboard
  arm64: dts: rockchip: move rk3399-sapphire PCIe to excavator baseboard
  arm64: dts: rockchip: assign clock rate for cpll child clocks on rk3399
  arm64: dts: rockchip: enable typec-phy0 for rk3399-puma-haikou
  arm64: dts: rockchip: enable typec-phy1 for rk3399-puma
  arm64: dts: rockchip: enable typec-phy for rk3399-firefly
  arm64: dts: rockchip: enable typec-phy for rk3399-sapphire
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Fixed pin numbers for uart4 on rk3288, iommu clocks and small changes
over multiple boards like default serial setting for rk3288-tinker,
output selection for the dp83867 on the phycore-som and the newly
added pwm-backlight delay properties for veyron boards.

* tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: default serial for rk3288 Tinker Board
  ARM: dts: rockchip: set PWM delay backlight settings for Minnie
  ARM: dts: rockchip: set PWM delay backlight settings for Veyron
  ARM: dts: rockchip: add clocks in iommu nodes
  ARM: dts: rockchip: Add dp83867 CLK_OUT muxing on rk3288-phycore-som
  ARM: dts: rockchip: fix uart4 pin-numbers for rk3288
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'juno-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt

ARMv8 Juno/Vexpress updates/cleanups for v4.18

1. Add the missing connections to the STM output port as all endpoint
   connections must be bidirectional.

2. Replace all the custom OF graph endpoint node names with the standard
   'endpoint'

3. Cleanup to replace all underscores('_') with hyphens('-') in the
   device node names

4. Syntactic restructuring of motherboard include file so that it can be
   included at the top of any other DTS file as it should be rather than
   existing include in the middle of the file at a specific location

* tag 'juno-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: juno/rtsm: re-structure motherboard includes
  arm64: dts: juno: replace '_' with '-' in node names
  arm64: dts: juno: Fix "debounce-interval" property misspelling
  arm64: dts: juno: fix OF graph endpoint node names
  arm64: dts: juno: fix missing Coresight STM graph connection
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt

ARMv7 Vexpress updates/cleanups for v4.18

1. Syntactic restructuring of motherboard include file so that it can be
   included at the top of any other DTS file as it should be rather than
   existing include in the middle of the file at a specific location

2. Use of standard GPIO controller bindings for few sysreg components
   like LED, MMC Write Protect/Card Detect and Flash Write Protect
   to fix some of the new DTC warnings

3. Cleanup to replace all underscores('_') with hyphens('-') in the
   device node names

* tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  ARM: dts: vexpress: replace '_' with '-' in node names
  ARM: dts: vexpress: use standard gpio bindings for sys_{led,mci,flash}
  ARM: dts: vexpress: Restructure motherboard includes
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'sti-dt-for-v4.18-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt

STi DT update:
 _ Fix complain about IRQ_TYPE_NONE_usage

* tag 'sti-dt-for-v4.18-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
  ARM: dts: stihxxx-b2120: Fix complain about IRQ_TYPE_NONE usage
  ARM: dts: stih410: Fix complain about IRQ_TYPE_NONE usage
  ARM: dts: stih407: Fix complain about IRQ_TYPE_NONE usage
  ARM: dts: stih407-pinctrl: Fix complain about IRQ_TYPE_NONE usage
  ARM: dts: stih407-family: Fix complain about IRQ_TYPE_NONE usage
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'v4.17-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt

- add clock and pinctrl nodes for mt2712e
- add High-Speed DMA and audio nodes for mt7622

* tag 'v4.17-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm64: dts: mt7622: add audio related device nodes
  arm64: dts: mt7622: add High-Speed DMA device nodes
  arm64: dts: mt2712: add pintcrl device node.
  arm64: dts: mt2712: add pintcrl file
  arm64: dts: add clock device nodes of MT2712
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'v4.17-next-dts32' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt

convert to SPDX IDs

mt7623:
- add audio, bluetooth, highspees DMA and SPI-NOR nodes
- fix invalid memory nodes by not using skeleton64.dtsi
- fix memory size for bananapi-r2
- fix dtc warnings
- refactor dts and dtsi to aviod code duplication
- add mt7623n and mt7623a reference boards

* tag 'v4.17-next-dts32' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
  arm: dts: mt7623: add MT7623N reference board with eMMC
  arm: dts: mt7623: add MT7623A reference boards
  arm: dts: mt7623: add MT7623A SoC level DTS
  arm: dts: mt7623: extend common file reused by all boards with MT7623 SoCs
  arm: dts: mt6323: move node mt6323 leds to mt6323.dtsi
  arm: dts: mt7623: add BTIF, HSDMA and SPI-NOR device nodes
  arm: dts: mt7623: fix all Warnings (unit_address_vs_reg)
  arm: dts: mt7623: fix available memory size on bananapi-r2
  arm: dts: mt7623: fix invalid memory node being generated
  arm: dts: mediatek: converted to using SPDX identifiers
  arm: dts: mediatek: modify audio related nodes for both MT2701 and MT7623
Signed-off-by: NOlof Johansson <olof@lixom.net>

It adds pinctrl device pinconf@8a21000, gpio-ranges for GPIO devices,
and then enables eMMC support for Hi3798CV200 Poplar board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

It adds usb2 phy devices, and enables ehci/ohci support for Hi3798CV200
Poplar board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

It adds combophy devices under peripheral controller and enables PCIe
support for Hi3798CV200 Poplar board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

The patch enables the HiSi LPC node for hip07, with
the IPMI child device.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

The patch enables the HiSi LPC node for hip06, with
IPMI and UART child devices.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Add pcie msi interrupt attribute for hi3660 SOC.
Signed-off-by: NYao Chen <chenyao11@huawei.com>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Add nodes and properties for thermal cooling management support.
Signed-off-by: NTao Wang <jean.wangtao@linaro.org>
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Add two CPU OPP tables, one table is corresponding to one cluster,
which allow CPU frequency scaling on hi3660 platforms.
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Add stub clock node for hi3660 platform.
Reviewed-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NKaihua Zhong <zhongkaihua@huawei.com>
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Add the mailbox controller node for hi3660 platform.
Signed-off-by: NKaihua Zhong <zhongkaihua@huawei.com>
Signed-off-by: NLeo Yan <leo.yan@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Merge tag 'samsung-dt64-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Samsung DTS ARM64 changes for v4.18

1. Fix DTC warnings.
2. Add mem-2-mem Scaler devices.

* tag 'samsung-dt64-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: dts: exynos: Add mem-2-mem Scaler devices
  arm64: dts: exynos: Remove unneeded address space mapping for soc node
  arm64: dts: exynos: Move syscon poweroff and restart nodes under the PMU
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Samsung DTS ARM changes for v4.18

1. Add support for USB OTG port on Origen board.
2. Allow earlycon on Rinato board.
3. Cleanup from obsolete properties.
4. Fix DTC warnings.
5. Remove Exynos5440 entirely.
6. Add mem-2-mem Scaler devices.

* tag 'samsung-dt-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Update x and y properties for mms114 touchscreen
  ARM: dts: exynos: Add mem-2-mem Scaler devices
  ARM: dts: s3c64xx: Remove skeleton.dtsi and fix DTC warnings for /memory
  ARM: dts: s3c24xx: Fix unnecessary address/size cells DTC warnings
  ARM: dts: s3c24xx: Remove skeleton.dtsi and fix DTC warning for /memory
  ARM: dts: exynos/s3c: Remove leading 0x and 0s from bindings notation
  ARM: dts: exynos: Remove Exynos5440
  ARM: dts: exynos: Remove unnecessary address/size properties in dp-controller of Exynos5
  ARM: dts: exynos: Bring order in fixed-regulators naming in Midas boards
  ARM: dts: exynos: Remove regulators node container in Origen and N710x
  ARM: dts: exynos: Remove unnecessary address/size properties in Origen
  ARM: dts: exynos: Remove unnecessary address/size properties in Midas boards
  ARM: dts: exynos: Fix invalid node referenced by i2c20 alias in Peach Pit and Pi
  ARM: dts: exynos: Move syscon poweroff and restart nodes under the PMU
  ARM: dts: exynos: Remove obsolete clock properties from power domains
  ARM: dts: exynos: Add serial path for Rinato board to get earlycon support
  ARM: dts: exynos: Add support for USB OTG port on Origen board
Signed-off-by: NOlof Johansson <olof@lixom.net>