dev_consume_skb_irq() should be called in wanxl_tx_intr() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in lmc_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.

Delete a redundant comment line in lmc_interrupt().
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Leslie Monis says:

====================
net: sched: pie: align PIE implementation with RFC 8033

The current implementation of the PIE queuing discipline is according to the
IETF draft [http://tools.ietf.org/html/draft-pan-aqm-pie-00] and the paper
[PIE: A Lightweight Control Scheme to Address the Bufferbloat Problem].
However, a lot of necessary modifications and enhancements have been proposed
in RFC 8033, which have not yet been incorporated in the source code of Linux.
This patch series helps in achieving the same.

Performance tests carried out using Flent [https://flent.org/]

Changes from v2 to v3:
  - Used div_u64() instead of direct division after explicit type casting as
    recommended by David

Changes from v1 to v2:
  - Excluded the patch setting PIE dynamically active/inactive as the test
    results were unsatisfactory
  - Fixed a scaling issue when adding more auto-tuning cases which caused
    local variables to underflow
  - Changed the long if/else chain to a loop as suggested by Stephen
  - Changed the position of the accu_prob variable in the pie_vars
    structure as recommended by Stephen
====================
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8033 replaces the IETF draft for PIE
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Random dropping of packets to achieve latency control may
introduce outlier situations where packets are dropped too
close to each other or too far from each other. This can
cause the real drop percentage to temporarily deviate from
the intended drop probability. In certain scenarios, such
as a small number of simultaneous TCP flows, these
deviations can cause significant deviations in link
utilization and queuing latency.

RFC 8033 suggests using a derandomization mechanism to avoid
these deviations.
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation scales the local alpha and beta
variables in the calculate_probability function by the same
amount for all values of drop probability below 1%.

RFC 8033 suggests using additional cases for auto-tuning
alpha and beta when the drop probability is less than 1%.

In order to add more auto-tuning cases, MAX_PROB must be
scaled by u64 instead of u32 to prevent underflow when
scaling the local alpha and beta variables in the
calculate_probability function.
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8033 suggests an initial value of 150 milliseconds for
the maximum time allowed for a burst of packets.
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8033 suggests a default value of 15 milliseconds for the
update interval.
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8033 suggests a default value of 15 milliseconds for the
target queue delay.
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8033 recommends a value of 16384 bytes for the queue
threshold.
Signed-off-by: NMohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: NDhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: NHrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: NManish Kumar B <bmanish15597@gmail.com>
Signed-off-by: NSachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Acked-by: NDave Taht <dave.taht@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable alloc_size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: aquantia: add hwmon support

This series adds HWMON support for the temperature sensor and the
related alarms on the 107/108/109 chips.

v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds HWMON support for the temperature sensor and the related
alarms on the 107/108/109 chips. This patch is based on work from
Nikita and Andrew. I added:
- support for changing alarm thresholds via sysfs
- move HWMON code to a separate source file to improve maintainability
- smaller changes like using IS_REACHABLE instead of ifdef
  (avoids problems if PHY driver is built in and HWMON is a module)

v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
Signed-off-by: NNikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename aquantia.c to aquantia_main.c to be prepared for adding new
functionality to separate source code files.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-02-22

This series contains updates to the ice driver only.

Bruce adds the __always_unused attribute to a parameter to avoid
compiler warnings when using -Wunused-parameter.  Fixed unnecessary
type-casting and the use of sizeof().  Fix the allocation of structs
that have become memory hogs, so allocate them in heaps and fix all the
associated references.  Fixed the "possible" numeric overflow issues
that were caught with static analysis.

Maciej fixes the maximum MTU calculation by taking into account double
VLAN tagging amd ensure that the operations are done in the correct
order.

Victor fixes the supported node calculation, where we were not taking
into account if there is space to add the new VSI or intermediate node
above that layer, then it is not required to continue the calculation.
Added a check for a leaf node presence for a given VSI, which is needed
before removing a VSI.

Jake fixes an issue where the VSI list is shared, so simply removing a
VSI from the list will cause issues for the other users who reference
the list.  Since we also free the memory, this could lead to
segmentation faults.

Brett fixes an issue where driver unload could cause a system reboot
when intel_iommu=on parameter is set.  The issue is that we are not
clearing the CAUSE_ENA bit for the appropriate control queues register
when freeing the miscellaneous interrupt vector.

Mitch is so kind, he prevented spamming the VF with link messages when
the link status really has not changed.  Updates the driver to use the
absolute vector ID and not the per-PF vector ID for the VF MSIx vector
allocation.

Lukasz fixes the ethtool pause parameter for the ice driver, which was
originally based off the link status but is now based off the PHY
configuration.  This is to resolve an issue where pause parameters could
be set while link was down.

Jesse updates the string that reports statistics so the string does not
get modified at runtime and cause reports of string truncation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function tc_dump_chain() obtains and releases block->lock on each iteration
of its inner loop that dumps all chains on block. Outputting chain template
info is fast operation so locking/unlocking mutex multiple times is an
overhead when lock is highly contested. Modify tc_dump_chain() to only
obtain block->lock once and dump all chains without releasing it.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Suggested-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using tcf_walker->stop flag to determine when tcf_walker->fn() was called
at least once is unreliable. Some classifiers set 'stop' flag on error
before calling walker callback, other classifiers used to call it with NULL
filter pointer when empty. In order to prevent further regressions, extend
tcf_walker structure with dedicated 'nonempty' flag. Set this flag in
tcf_walker->fn() implementation that is used to check if classifier has
filters configured.

Fixes: 8b64678e ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Suggested-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 787799a9 sets the SERDES interfaces of 6390 and 6390X to
1000BaseX, but this is only needed on 6390X, since there are SERDES
interfaces which can be used on lower ports on 6390.

This commit fixes this by returning to previous behaviour on 6390.
(Previous behaviour means that CMODE is not set at all if requested mode
is NA).

This is needed on Turris MOX, where the 88e6190 is connected to CPU in
2500BaseX mode.

Fixes: 787799a9 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: NMarek Behún <marek.behun@nic.cz>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per discussion with Daniel[1] and Eric[2], these SOCK_DEBUG() calles in
TCP are not needed now.
We'd better clean up it.

[1] https://patchwork.ozlabs.org/patch/1035573/
[2] https://patchwork.ozlabs.org/patch/1040533/Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

parameter state in the tcp_sacktag_bsearch() is not used.
So, it can be removed.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A test started warning on a string truncation. This led to an unfortunate
realization that we are likely not accounting for the stats length
correctly before this patch, so fix the issue by putting "port." in front
of all the PF stats, instead of magically prepending it at runtime.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethtool reported pause params based on the currently negotiated
link settings instead of current PHY config. User was not able
to turn off pause params because ethtool was incorrectly reporting
parameters as off when link was down even though PHY was configured
to support pause frames. Now pause params are taken from PHY config
instead of link status.
Signed-off-by: NLukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the PF driver sets up the VF MSI-X vector allocation, it needs to
use the hardware absolute vector ID, not the per-PF vector ID. Without
this change we see (apparent) TX hangs when using VFs on multiple PFs.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for a leaf node presence for a given VSI. This check is required
before removing a VSI since VSIs can't be removed with enabled queues
(with leaf nodes) from the FW scheduler tree unless its a reset.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the flush Tx pipe flag instead of getting an EAGAIN error when FW
times out in processing the disable Tx queue command.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On older devices like X710 and X722, the VF's ARQLEN register is cleared
on reset, so the VF driver uses that register to detect an unannounced
reset. Unfortunately, on devices controlled by ice, this register is NOT
cleared on reset. This causes the VF to miss resets, and even on
properly-announced resets, the VF driver complains that it didn't see
the reset.

To fix this, we'll do it in software. When we handle a VF reset (whether
triggered by software or VFLR), clear this register after the HW reset
is complete.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't send a link message to the VFs unless link actually changes state.
This avoids a small timing hole in some VF drivers that can cause an
apparent TX hang if they receive a link status message at the wrong time.

Although we have fixed the timing hole in the current VF driver, there
are still lots of drivers in the field that have this timing hole. Let's
not fall into it if we can avoid it.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_vsi_release we are always assigning a value to the local VF
variable. Change this to only be assigned if the VSI is a VF VSI.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When compiling and analyzing the driver on newer kernels, a static
analyzer warns about the following "numeric overflow" issues:

  "The result of expression: 'budget-1' generates 4-byte type while casting
   to a bigger size of 8-byte".

  "The result of expression: '*words-words_read' generates 4-byte type
   while casting to a bigger size of 8-byte".

Fix them both.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the kernel has the intel_iommu=on parameter set, on some
platforms removing the driver causes a system reboot. In initialization
we associate the control queue interrupts with the pf->hw_oicr_idx and
enable the interrupts by setting the CAUSE_ENA bit. The problem comes
on teardown because we are not clearing the CAUSE_ENA bit for the
control queues, but the vector at pf->hw_oicr_idx (miscellaneous
interrupt vector) gets disabled.

Fix this by clearing the CAUSE_ENA bit in the appropriate control queue
registers on when freeing the miscellaneous interrupt vector. Also,
move the call to ice_free_irq_msix_misc() to after ice_deinit_sw() in
ice_remove() because ice_deinit_sw() makes an AQ call, but
ice_free_irq_msix_misc() disables the miscellaneous vector and it's
associated interrupts.

Also, create two small helper functions to enable and disable the
control queue interrupts respectively.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When adding multiple VLANs to the same VSI, the ice_add_vlan code will
share the VSI list, so as not to create multiple unnecessary VSI lists.

Consider the following flow

  ice_add_vlan(hw, <VSI 0 VID 7, VSI 0 VID 8, VSI 0 VID 9>)

Where we add three VLAN filters for VIDs 7, 8, and 9, all for VSI 0.

The ice_add_vlan will create a single vsi_list and share it among all
the filters.

Later, if we try to remove a VLAN,

  ice_remove_vlan(hw, <VSI 0 VID 7>)

Then the removal code will update the vsi_list and remove VSI 0 from it.
But, since the vsi_list is shared, this breaks the list for the other
users who reference it. We actually even free the VSI list memory, and
may result in segmentation faults.

This is due to the way that VLAN rule share VSI lists with reference
counts, and is caused because we call ice_rem_update_vsi_list even when
the ref_cnt is greater than one.

To fix this, handle the case where ref_cnt is greater than one
separately. In this case, we need to remove the associated rule without
modifying the vsi_list, since it is currently being referenced by
another rule. Instead, we just need to decrement the VSI list ref_cnt.

The case for handling sharing of VSI lists with multiple VSIs is not
currently supported by this code. No such rules will be created today,
and this code will require changes if/when such code is added.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

struct ice_vsi_ctx has gotten large enough that function local declarations
of it on the stack are causing stack hogs.  Fix that by allocating the
structs on heap.  Cleanup some formatting issues in the code around these
changes and fix incorrect data type uses of returned functions in a couple
places.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With sizeof(), it is preferable to use the variable of type <type> instead
of sizeof(<type>).

There are multiple places where a temporary variable is used to hold a
'size' value which is then used for a subsequent alloc/memset. Get rid
of the temporary variable by calculating size as part of the alloc/memset
statement.

Also remove unnecessary type-cast.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VSI supported nodes are calculated in order to add the VSI parent or
intermediate nodes to the scheduler tree. If one of the node in below
layers (from VSI layer) has space to add the new VSI or intermediate node
above that layer then it's not required to continue the calculation further
for below layers.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently ICE_MAX_MTU subtracts only ETH_HLEN from max frame size and
adds ETH_FCS_LEN and VLAN_HLEN, which is not what was intended.
The ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN expression should be surrounded
with parentheses.

Wrap mentioned expression and take into account VLAN double tagging.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 87b0984e ("net: Add extack argument to ndo_fdb_add()") in
net-next added an extended parameter to the .ndo_fdb_add op and changed
ice_fdb_add() accordingly. Update the function header and add the
__always_unused attribute to the new parameter to avoid -Wunused-parameter
warnings.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We have no more in tree users of switchdev_port_attr_get() after
d0e698d5 ("Merge branch 'net-Get-rid-of-switchdev_port_attr_get'")
so completely remove the function signature and body.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the switch to phy_resolve_aneg_linkmode() we don't read from the
chip any longer what is advertised but use phydev->advertising directly.
For a fixed phy however this bitmap is empty so far, what results in
no common mode being found. This breaks DSA. Fix this by advertising
everything that is supported. For a normal phy this done by phy_probe().

Fixes: 5502b218 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>