The current PL011 driver transmits a dummy character when the UART
is opened, to assert the TX IRQ for the first time
(see pl011_startup()).  The UART is put in loopback mode temporarily,
so the receiver presumably shouldn't see anything.

However...

At least some platforms containing a PL011 send characters down the
wire even when loopback mode is enabled.  This means that a
spurious NUL character may be seen at the receiver when the PL011 is
opened through the TTY layer.

The current code also temporarily sets the baud rate to maximum and
the character width to the minimum, to that the dummy TX completes
as quickly as possible.  If this is seen by the receiver it will
result in a framing error and can knock the receiver out of sync --
turning subsequent output into garbage until synchronisation
is reestablished.  (Particularly problematic during boot with systemd.)

To avoid spurious transmissions, this patch removes assumptions about
whether the TX IRQ will fire until at least one TX IRQ has been seen.

Instead, the UART will unmask the TX IRQ and then slow-start via
polling and timer-based soft IRQs initially.  If the TTY layer writes
enough data to fill the FIFO to the interrupt threshold in one go,
the TX IRQ should assert, at which point the driver changes to
fully interrupt-driven TX.

In this way, the TX IRQ is activated as a side-effect instead of
being done deliberately.

This should also mean that the driver works on the SBSA Generic
UART[1] (a cut-down PL011) without invasive changes.  The Generic
UART lacks some features needed for the dummy TX approach to work
(FIFO disabling and loopback).

[1] Server Base System Architecture (ARM-DEN-0029-v2.3)
    http://infocenter.arm.com/
    (click-thru required :/)
Signed-off-by: NDave Martin <Dave.Martin@arm.com>
Tested-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All instances of "ttyPS" use this macro except for this one. Convert
it.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Spreadtrum UART is accessed with mmio; declare the proper iotype.
Also prevent userspace from assigning any other iotype via
ioctl(TIOCSSERIAL).
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The transmitter is expected to be controlled by the UART's RTS pin.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Support for IRDA was added in 2009 in commit v2.6.31-rc1~399^2~2. There
are no in-tree users.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix indention, remove old address of the FSF, remove in-file changelog,
mention Freescale.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no benefit in keeping this information in RAM when it's not
used any more, so better use function local variables instead.

These members are unused since c0d1c6b0 ("serial: imx: Fix the
reporting of interrupts")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This if (0) exists since the driver was introduced in commit
c49bde83eb6a ([ARM PATCH] 1956/2: Re: Motorola i.MX serial driver)
back in 2004.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The writeable bits in the USR2 register are all "write 1 to
clear" so only write the bits that actually should be cleared.

Fixes: f1f836e4 ("serial: imx: Add Rx Fifo overrun error message")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we have a native 8250 driver carrying the Intel MID serial devices the
specific support is not needed anymore. This patch removes it for Intel MID.

Note that the console device name is changed from ttyMFDx to ttySx.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Penwell supports 3 HSUART ports which are 8250 compatible. The patch adds
necessary bits to the driver.

The functions have intel_mid_* prefix due to more than one platform will use
this code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The HSU DMA is developed to support High Speed UART controllers found in
particular on Intel MID platforms such as Intel Medfield.

The existing implementation is tighten to the drivers/tty/serial/mfd.c driver
and has a lot of disadvantages. Besides that we would like to get rid of the
old HS UART driver in regarding to extending the 8250 which supports generic
DMAEngine API. That's why the current driver has been developed.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed misspelling of 'Medfield'
Signed-off-by: NJoseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Current code uses the alias id as array subscript of ar933x_console_ports.
So the valid id is 0 ... CONFIG_SERIAL_AR933X_NR_UARTS - 1.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of ignoring errors returned by devm_gpiod_get_index use
devm_gpiod_get_index_optional which results in slightly more strict
error handling which is good.

Also use the fourth parameter to devm_gpiod_get_index_optional to be
able to drop the explicit direction setting.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Drivers using mctrl-gpio must not pass invalid values for struct
mctrl_gpios *. All drivers were fixed in this regard and so some checks
can go away or be simplified.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If mctrl_gpio_init returns an error code this value should be forwarded and
the driver must not simply ignore this failure.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

mctrl_gpio_init is fully aware of being optional. If it returns an error
code this indicates a real error that must not be ignored.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

mctrl_gpio_init at present doesn't return NULL. (It might be used in the
future when no gpios are to be used indicating success.) Properly pass
error returned and also make driver probing fail on error.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UBRC is a read-only register, so we should not store and restore it inside
imx_flush_buffer().
Reported-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

this patch fixes following sparse warnings:

bcm63xx_uart.c:857:43: warning: Using plain integer as NULL pointer
bcm63xx_uart.c:871:35: warning: Using plain integer as NULL pointer
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Without this the module does not load automatically whenever suitable
platform device appears.
Reported-by: NJerome Blin <jerome.blin@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Building sprd_serial.o when CONFIG_PM_SLEEP is not defined triggers
these warnings:
    drivers/tty/serial/sprd_serial.c:755:12: warning: ‘sprd_suspend’ defined but not used [-Wunused-function]
     static int sprd_suspend(struct device *dev)
                ^
    drivers/tty/serial/sprd_serial.c:764:12: warning: ‘sprd_resume’ defined but not used [-Wunused-function]
     static int sprd_resume(struct device *dev)
                ^

Let's compile these functions only when CONFIG_PM_SLEEP is defined.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make of_device_id array const.
Signed-off-by: NSanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No functional changes.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redudant calls to the PCI for changing a power state since it's done by bus
code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the current kernel, the CONFIG_PPC_OF is always 'y' for the ppc
arch. So we don't need to check it with other ppc specific options.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.

Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As more ARM platforms are moving into ARCH_MULTIPLATFORM, we can now
have integrator and versatile in the same kernel, and first one selects
this driver, causing a Kconfig warning:

warning: (ARCH_INTEGRATOR_AP) selects SERIAL_AMBA_PL010 which has unmet direct dependencies (TTY && HAS_IOMEM && ARM_AMBA && (BROKEN || !ARCH_VERSATILE))

It turns out that it has not been broken on versatile for a long time,
so we can remove the statement here.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a tricky story of the new atomic state handling and the legacy
code fighting over each another. The bug at hand is an underrun of the
framebuffer reference with subsequent hilarity caused by the load
detect code. Which is peculiar since the the exact same code works
fine as the implementation of the legacy setcrtc ioctl.

Let's look at the ingredients:

- Currently our code is a crazy mix of legacy modeset interfaces to
  set the parameters and half-baked atomic state tracking underneath.
  While this transition is going we're using the transitional plane
  helpers to update the atomic side (drm_plane_helper_disable/update
  and friends), i.e. plane->state->fb. Since the state structure owns
  the fb those functions take care of that themselves.

  The legacy state (specifically crtc->primary->fb) is still managed
  by the old code (and mostly by the drm core), with the fb reference
  counting done by callers (core drm for the ioctl or the i915 load
  detect code). The relevant commit is

  commit ea2c67bb
  Author: Matt Roper <matthew.d.roper@intel.com>
  Date:   Tue Dec 23 10:41:52 2014 -0800

      drm/i915: Move to atomic plane helpers (v9)

- drm_plane_helper_disable has special code to handle multiple calls
  in a row - it checks plane->crtc == NULL and bails out. This is to
  match the proper atomic implementation which needs the crtc to get
  at the implied locking context atomic updates always need. See

  commit acf24a39
  Author: Daniel Vetter <daniel.vetter@ffwll.ch>
  Date:   Tue Jul 29 15:33:05 2014 +0200

      drm/plane-helper: transitional atomic plane helpers

- The universal plane code split out the implicit primary plane from
  the CRTC into it's own full-blown drm_plane object. As part of that
  the setcrtc ioctl (which updated both the crtc mode and primary
  plane) learned to set crtc->primary->crtc on modeset to make sure
  the plane->crtc assignments statate up to date in

  commit e13161af
  Author: Matt Roper <matthew.d.roper@intel.com>
  Date:   Tue Apr 1 15:22:38 2014 -0700

      drm: Add drm_crtc_init_with_planes() (v2)

  Unfortunately we've forgotten to update the load detect code. Which
  wasn't a problem since the load detect modeset is temporary and
  always undone before we drop the locks.

- Finally there is a organically grown history (i.e. don't ask) around
  who sets the legacy plane->fb for the various driver entry points.
  Originally updating that was the drivers duty, but for almost all
  places we've moved that (plus updating the refcounts) into the core.
  Again the exception is the load detect code.

Taking all together the following happens:
- The load detect code doesn't set crtc->primary->crtc. This is only
  really an issue on crtcs never before used or when userspace
  explicitly disabled the primary plane.

- The plane helper glue code short-circuits because of that and leaves
  a non-NULL fb behind in plane->state->fb and plane->fb. The state
  fb isn't a real problem (it's properly refcounted on its own), it's
  just the canary.

- Load detect code drops the reference for that fb, but doesn't set
  plane->fb = NULL. This is ok since it's still living in that old
  world where drivers had to clear the pointer but the core/callers
  handled the refcounting.

- On the next modeset the drm core notices plane->fb and takes care of
  refcounting it properly by doing another unref. This drops the
  refcount to zero, leaving state->plane now pointing at freed memory.

- intel_plane_duplicate_state still assume it owns a reference to that
  very state->fb and bad things start to happen.

Fix this all by applying the same duct-tape as for the legacy setcrtc
ioctl code and set crtc->primary->crtc properly.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reported-and-tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull GPIO fixes from Linus Walleij:
 "Two GPIO fixes:

   - Fix a translation problem in of_get_named_gpiod_flags()

   - Fix a long standing container_of() mistake in the TPS65912 driver"

* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: tps65912: fix wrong container_of arguments
  gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node

Merge branch 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal

Pull thermal management fixes from Eduardo Valentin:
 "Specifics:

   - Several fixes in tmon tool.

   - Fixes in intel int340x for _ART and _TRT tables.

   - Add id for Avoton SoC into powerclamp driver.

   - Fixes in RCAR thermal driver to remove race conditions and fix fail
     path

   - Fixes in TI thermal driver: removal of unnecessary code and build
     fix if !CONFIG_PM_SLEEP

   - Cleanups in exynos thermal driver

   - Add stubs for include/linux/thermal.h.  Now drivers using thermal
     calls but that also work without CONFIG_THERMAL will be able to
     compile for systems that don't care about thermal.

  Note: I am sending this pull on Rui's behalf while he fixes issues in
  his Linux box"

* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: int340x_thermal: Ignore missing _ART, _TRT tables
  thermal/intel_powerclamp: add id for Avoton SoC
  tools/thermal: tmon: silence 'set but not used' warnings
  tools/thermal: tmon: use pkg-config to determine library dependencies
  tools/thermal: tmon: support cross-compiling
  tools/thermal: tmon: add .gitignore
  tools/thermal: tmon: fixup tui windowing calculations
  tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
  tools/thermal: tmon: add min/max macros
  tools/thermal: tmon: add --target-temp parameter
  thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
  thermal: rcar: Make error and remove paths symmetrical with init
  thermal: rcar: Fix race condition between init and interrupt
  thermal: Introduce dummy functions when thermal is not defined
  ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
  thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP

Pull md fixes from Neil Brown:
 "Three md fixes:

   - fix a read-balance problem that was reported 2 years ago, but that
     I never noticed the report :-(

   - fix for rare RAID6 problem causing incorrect bitmap updates when
     two devices fail.

   - add __ATTR_PREALLOC annotation now that it is possible"

* tag 'md/4.0-fixes' of git://neil.brown.name/md:
  md: mark some attributes as pre-alloc
  raid5: check faulty flag for array status during recovery.
  md/raid1: fix read balance when a drive is write-mostly.

Pull arch/metag fix from James Hogan:
 "This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
  macros for metag which have always been erronously returning the PC
  and stack pointer of the task's kernel context rather than from its
  user context saved at entry from userland into the kernel, which
  affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"

* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
  metag: Fix KSTK_EIP() and KSTK_ESP() macros

Pull x86 fixes from Ingo Molnar:
 "A CR4-shadow 32-bit init fix, plus two typo fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too
  x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup()
  x86/cpu/intel: Fix trivial typo in intel_tlb_table[]

Pull timer fixes from Ingo Molnar:
 "Three clockevents/clocksource driver fixes"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: pxa: Fix section mismatch
  clocksource: mtk: Fix race conditions in probe code
  clockevents: asm9260: Fix compilation error with sparc/sparc64 allyesconfig

Pull perf fixes from Ingo Molnar:
 "Two kprobes fixes and a handful of tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Make sparc64 arch point to sparc
  perf symbols: Define EM_AARCH64 for older OSes
  perf top: Fix SIGBUS on sparc64
  perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag
  perf tools: Fix pthread_attr_setaffinity_np build error
  perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check
  perf bench: Fix order of arguments to memcpy_alloc_mem
  kprobes/x86: Check for invalid ftrace location in __recover_probed_insn()
  kprobes/x86: Use 5-byte NOP when the code might be modified by ftrace